Page 1
®
CCQ1400A-4
Color CCD Camera
with 4 mm Lens
Installation/
Operation Manual
C1969M-A (1/02)
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150
International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120
Page 2
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P encolsure, it is designed for indoor use only
and it must not be installed where exposed to rain and moisture.
3. Only use replacement parts recommended by Pelco.
4. When used with the CCQ1400A-4 cameras with audio, the Pelco PCMQ14A Observation System is capable of being used as a
two-way intercom system. Applications other than the intended use as a two-way intercom communications system may vio-
late Federal wiretapping laws. No systems may be used to monitor audio without the express knowledge of the parties
being monitored. A warning notice has been included as a part of this manual. Photocopying of this notice is permitted and encouraged. Signs
CCQ1400A-4 intercom system. Pelco assumes no liability for equipment being used for purposes other than the intended use
as a two-way intercom system.
5. Do not attempt to disassemble the unit.
6. Do not remove screws or cover.
7. There are no user-serviceable parts inside.
8. Do not install any of the system parts where they will be exposed to water, excessive dust or excessive vibration.
The product and/or manual may bear the following marks:
must
be posted and plainly visible at all entrances to public and private premises utilizing the PMCQ14A/
This symbol indicates that dangerous voltage constituting a risk of electric shock is
present within this unit.
This symbol indicates that there are important operating and maintenance instructions
in the literature accompanying this unit.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.
2 Pelco Manual C1969M-A (1/02)
Page 3
DESCRIPTION
OVERVIEW
The CCQ1400A-4 color CCD camera with 4 mm lens is designed for use with the PMCQ14A 14-inch color quad monitor.
A mini-DIN 6 connector in the back of the camera matches the connector on the back of the monitor. Power, alarm, audio and video
contacts are all provided at this connector.
MODELS
CCQ1400A-KIT Camera assembly with audio, consisting of one CCQ1400A-4 camera, one WMQ8 bracket and one
CCQCABLE-60 cable.
CCQ1400A-4 1/4-inch color CCD camera with 4 mm lens, 12 VDC, with a microphone and speaker
INSTALLATION
INSTALLATION TIPS
• Do not locate components or cable where they will get wet.
NO SHARP BENDS
• Lay cable loosely in attic or under floor.
• Do not tightly bundle with other wires.
•Avoid sharp bends in the cable.
• Do not directly staple the cable to any surface.
•Try to locate cable away from power lines and fluorescent fixtures.
• If a power line or fixture is in the way, take the cable across it at right angles.
• Do not run cables parallel to fixtures or power lines.
STORE EXTRA CABLE
SERPENTINE FASHION
• The cable is 60 feet long. Do not try to shorten it.
• Extra cable should be spread out serpentine style.
•Avoid coiling up extra cable.
CROSS AC POWER LINES AND FLORESCENT
FIXTURES AT RIGHT ANGLES
NO STAPLES
AC
VIDEO
UNPACKING
The camera is shipped as a camera only or as a kit. Unpack and inspect the contents carefully.
Camera Kit Camera Only
1 Camera 1 Camera
1 Camera bracket
1 Camera bracket base
1 Cable
Pelco Manual C1969M-A (1/02) 3
Page 4
INSTALLING THE CAMERA
1. Assemble and mount the camera and bracket.
NOTE:
screws for masonry or hollow wall mounting, be sure to use #6 or 4 mm hardware.
2. Run cables. Refer to
The screws provided are intended for wood. If it is necessary to substitute
Installation Tips
.
BALL JOINT
THUMB NUT
SET SCREW
CAMERA
BRACKET
20106
MICROPHONE
MONITOR
MIC
THUMB NUT
SET SCREW
ALARM
BRACKET BASE
20103
MIC
MONITOR
ALARM
IN GND
MONITOR
20105
3. Connect cable to camera. Insert plug with the arrow facing up.
MIC
ALARM
IN GND
4. Connect alarm contacts, if used.
5. Connect cable to one of the CH IN jacks on the back of the monitor
(refer to Figure 1).
6. Set impedance switch to the 75-ohm position,unless another video
device is connected to the IN/OUT jacks (refer to Figure 1).
IN GND
N.C. OR N.O. CONTACT
20107
7. Connect AC power to monitor (refer to Figure 1).
8. Turn on MAIN switch on the back of the monitor (refer to Figure 1). Then press the POWER button on the front of the monitor.
9. Test according to the checkout procedure in Table A.
CAMERA 1 CAMERA 2 CAMERA 3 CAMERA 4
FOCUS
SCREEN
TO AC
OUTLET
A/C INLET
MAIN
ALTERNA TE ALARM CONT ACT
(WHEN CONTACTS ON THE
CAMERA ARE NOT USED)
75 Hi 75 Hi 75 Hi 75 Hi 75 Hi
IN
IN/OUT
CH 1
CH 1 CH 2 CH 3 CH 4 TRIG
VIDEO AUDIO
MONITOR
CH 3 CH 4CH 2
OUT
*NOT USED IN STANDARD INSTALLATION. CONTACT
PELCO IF REMOTE CONTROL IS REQUIRED.
OUT
REMOTE
*
IN
OUT
TO VCR (WHEN AUDIO
IS NOT USED)
TO VCR (OPTIONAL)
IF AUDIO IS USED
TO VCR
TRIGGER
Figure 1. Connections at the Back of the Monitor
4 Pelco Manual C1969M-A (1/02)
Page 5
CHECKOUT
Table A. Checkout Procedure When Adding a Camera to the System
This procedure assumes that power is on and that the full monitor checkout has been performed.
STEP PROCEDURE RESULTS
1 Calibrate camera.
2 At the monitor, press the CH button for the channel
the new camera is using.
3 Press the ZOOM/FREEZE button.
Use arrow keys to move the highlighted area.
Press the QUAD/MENU button.
Press the QUAD/MENU or the ZOOM/FREEZE button.
4 Put an object in the area being observed by the
camera.
While holding the RESET/ALT button, press the
ZOOM/FREEZE button.
Remove the object from the observed area.
Press the ALT + FREEZE button.
5 Perform this step if the camera is equipped for the
audio function.
Have a person stand near the camera and speak.
Increase the volume control on the monitor,
if necessary.
Press and hold the AUDIO/TALK button on the
monitor.
Talk in a normal voice.
Release the AUDIO/TALK button.
6 Perform this step if the alarm contacts are
connected to a detection switch.
Momentarily activate the alarm contacts.
Press the RESET button on the front of the monitor.
The CCQ1400A-4 camera is factory set for back focus.
No further calibration is needed.
See camera image full screen.
Zoom area is highlighted in the center of the screen.
The highlighted area moves to different parts of the screen.
The image zooms to show the selected area full screen.
See the selected channel image full screen (normal).
See the object on the screen. Any movement will be seen.
See the object frozen on the screen. No movement will be
seen.
The object remains on the screen.
The object disappears and movement is once again seen.
Hear the person at the camera speaking.
The person at the camera should hear you.
Hear the person or other sounds near the camera.
ALM flashes at the top of the monitor screen.
ALM goes away.
7 Checkout is complete.
Pelco Manual C1969M-A (1/02) 5
Page 6
TECHNICAL SPECIFICATIONS
ELECTRICAL
Input Voltage: 12 VDC, +/-2 VDC
Power
Consumption: 2 watts
Signal Format: NTSC
Scanning System: 2:1 interlace
Sync System: Internal
Horizontal
Resolution: 330 TV lines (center)
Image Size Area: 4.57 mm (H) x 3.90 mm (V)
Picture Elements: 512 (H) x 492 (V)
Electronic Iris: 1/60 to 1/100,000 second
Video Output: 1.0 Vp-p, +/-10%, 75 ohms
Auto White Bal.: Electronic auto tracking
Minimum
Illumination: 0.9 lux at 30 IRE, f1.2
GENERAL
Lens: C/CS Mount, F2.0, 4 mm lens
Dimensions: 2.00 (W) x 4.00 (L) x 2.38 (H) inches (5.08 x 10.16 x 6.05 cm)
Weight: 0.5 lb (0.22 kg)
ENVIRONMENTAL
Operating T emp.: 14° to 131°F (-10° to 55°C)
Storage T emp.: 4° to 158°F (-20° to 70°C)
Humidity 35% to 80%, non-condensing
(Design and product specifications subject to change without notice.)
THE FOLLOWING PAGE MAY BE CO PIE D.
6 Pelco Manual C1969M-A (1/02)
Page 7
Notice:
Audio Monitoring
on these Premises
Page 8
REGULATORY NOTICES
Note: This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
®
• Three years on Genex
• Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
•Two years on standard motorized or fixed focal length lenses.
•Two years on Legacy
fixed dome products.
•Two years on Spectra
continuous motion applications.
•Two years on Esprit
• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
Series products (multiplexers, server, and keyboard).
®
, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
®
, Esprit®, ExSite™, and PS20 scanners, including when used in
®
and WW5700 Series window wiper (excluding wiper blades).
™
Series distributed network-based video products.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
REVISION HISTORY
Manual # Date Comments
C1969M 2/00 Original version.
C1969M-A 1/02 Revised camera drawings because of redesign. Added specification for minimum illumination. Removed models without
audio.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 2002, Pelco.
Endura and ExSite are trademarks of Pelco. All rights reserved.
8 Pelco Manual C1969M-A (1/02)
Loading...