Pelco C1959M User Manual

PMC21A
21-Inch Color Monitor
Installation/
Operation Manual
C1959M (6/99)
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120

CONTENTS

LIST OF ILLUSTRATIONS

Section Page
IMPORTANT SAFEGUARDS AND WARNINGS ................................................................3
DESCRIPTION ...................................................................................................................3
INSTALLATION................................................................................................................... 3
OPERATION ...................................................................................................................... 5
FRONT PANEL CONTROLS......................................................................................5
PASSIVE LOOPING ...................................................................................................5
MAINTENANCE ................................................................................................................. 6
SPECIFICATIONS..............................................................................................................6
WARRANTY AND RETURN INFORMATION .................................................................... 8
Figure Page
1 Bezel Rack Mount Installation ............................................................................3
2 Rear Panel Connections .................................................................................... 4
3 One Monitor with External Video Equipment ..................................................... 4
4 Monitor Looping with External Video Equipment ............................................... 4
5 S-VHS Video (Y/C) Input Connections ...............................................................5
6 Front Panel Controls ..........................................................................................5
7 PMC21A Dimension Drawing.............................................................................7
8 Bezel Rack Mount Dimension Drawing ..............................................................7

LIST OF TABLES

Table Page
AVideo Coaxial Cable Requirements ................................................................... 4
2 Pelco Manual C1959M (6/99)

IMPORTANT SAFEGUARDS AND WARNINGS

Observe the following warnings before installing and using this product.
1. Installation and servicing should be done by qualified installation and service person­nel only.
2. Installation should be done according to all local and national electrical and mechani­cal codes, using only approved materials.
3. Use only installation methods and materials capable of supporting four times the maxi­mum specified load.
4. A CCC-approved power cord must be used to power this equipment when used in China.
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

DESCRIPTION

The PMC21A is a high-resolution color monitor that can be used in desktop applications or rack mounted using the bezel rack mount that is provided as a standard accessory. The rack mount is constructed of steel, has a black finish, and occupies 11 rack unit spaces. It is supplied with eight flat-head screws to attach the rack mount to the monitor, and four 10-32 screws to attach the rack mount to a console.
The monitor supports NTSC and PAL video, as well as 120 VAC and 230 VAC input power. An automatic switching system makes all the necessary changes for adapting to the re­quired formats. Manual selection is not required. A separate power cord is supplied for each voltage input.

INSTALLATION

CAUTION:
not install this
monitor in a location having excessive heat or in any way that obstructs the ventilation openings in the cabinet. Premature component failure or cabinet damage may result.
NOTE:
Installation of the monitor and rack mount into the console may require two persons.
Do
The PMC21A features audio input and output, and has a steel housing and front panel con­trols. The S-VHS high-resolution video (420 horizontal lines at center) and digital comb filter circuitry add to the superior picture quality.
To install the monitor in a rack, start at step 1. Otherwise, start at step 3.
1. Slide the bezel rack mount onto the monitor from the rear and attach it to the monitor with the eight M5 flat-head screws provided.
2. Place the PMC21A monitor and rack mount into the console, align the mounting holes of the rack mount with the mounting holes in the console, and insert and tighten the four 10-32 screws provided. The face of the monitor protrudes approximately 4.8 inches (12.2 cm) from the front of the rack.
FLATHEAD SCREW (8)
BEZEL RACK MOUNT
PMC21A MONITOR

Figure 1. Bezel Rack Mount Installation

Pelco Manual C1959M (6/99) 3
3. Connect the equipment as shown in Figures 2 through 5. Refer to Table A for the type of video coaxial cable to use.
Table A. Video Coaxial Cable Requirements
Cable Type* Maximum Distance
RG59/U 750 ft (229 m)
RG6/U 1,000 ft (305 m)
RG11/U 1,500 ft (457 m)
*Minimum cable requirements:
75 ohms impedance All-copper center conductor All-copper braided shield with 95% braid coverage
4. Set the IMPEDANCE switch on the monitor(s) to HIGH if the VIDEO OUT connection is used. Otherwise, set the switch(es) to the 75-OHM position.
5. Plug the appropriate power cord into the AC INLET connection on the rear panel of the monitor (refer to Figure 2). Plug the other end into a power receptacle.
AC INLET
AUDIO OUT JACK (RCA)
CAMERA INPUT JACK (BNC)
S-VHS IN
AUDIO
VIDEO OUT JACK (BNC)
OUT
CAMERA
INPUT
IN
75 HIGH
IMPEDANCE
VIDEO
OUT
AUDIO
S-VHS JACK
AUDIO IN JACK (RCA)
IMPEDANCE SWITCH (75/HIGH)

Figure 2. Rear Panel Connections

OUT
S-VHS IN
AUDIO
CAMERA
INPUT
IN
75 HIGH
IMPEDANCE
VIDEO
OUT

Figure 3. One Monitor with External Video Equipment

MAXIMUM OF THREE MONITORS
OUT
CAMERA
INPUT
IN
75 HIGH
IMPEDANCE
VIDEO
OUT
CAMERA
AUDIO
OUT
CAMERA
INPUT
IN
75 HIGH
IMPEDANCE
VIDEO
OUT
OUT
AUDIO
IN
CAMERA
VCR
CAMERA
INPUT
VCR
75 HIGH
IMPEDANCE
VIDEO
OUT

Figure 4. Monitor Looping with External Video Equipment

4 Pelco Manual C1959M (6/99)

OPERATION

FRONT PANEL CONTROLS

OUT
S-VHS IN
AUDIO
CAMERA
INPUT
75 HIGH
IN
IMPEDANCE
VIDEO
OUT
VCR

Figure 5. S-VHS Video (Y/C) Input Connections

Refer to Figure 6 for front panel controls.
1. Press the POWER switch to turn the monitor on. The power LED lamp above the switch will illuminate when the power is applied.
2. Press the VIDEO/S-VHS switch to select the S-VHS mode if the S-VHS input jack on the rear of the monitor is used. Otherwise, select the VIDEO mode. The mode is mo­mentarily displayed on the upper right portion of the monitor screen at the time it is se­lected.
3. Adjust the VOLUME control for the desired audio level. Turn the control clockwise to in­crease and counterclockwise to decrease.
4. Adjust the CONT. control for the desired overall contrast. Proper adjustment will allow maximum gradations between the darkest and lightest picture contrast. Turn the con­trol clockwise to increase and counterclockwise to decrease.
5. Adjust the BRIGHT control for the desired overall display brightness. This control is also useful to compensate for differences in surrounding area lighting. Turn the control clockwise to increase and counterclockwise to decrease.
6. Adjust the COLOR control to set the color saturation level. Turn the control clockwise to increase and counterclockwise to decrease.
7. Adjust the SHARP control to obtain the clearest picture.
8. Adjust the TINT control for the proper color phase or flesh tones. When turned clock­wise, the skin tone becomes greenish. When turned counterclockwise, skin tone be­comes reddish.

PASSIVE LOOPING

Passive looping is accomplished when two or three monitors are connected in series (see Figure 4) and a looping signal is sent through the IN and OUT connectors of one monitor and to the next in series. Unless you want to view the monitor(s), none of them need to be turned on for passive looping to function.
VIDEO/S-VHS
PMC21A
TNT SHARP COLOR BRIGHT CONT. VOLUME POWER

Figure 6. Front Panel Controls

POWER LED LAMP
Pelco Manual C1959M (6/99) 5

MAINTENANCE

If the quality of the picture is poor and cannot be improved by making adjustments on the front control panel, inspect all system connections and cable runs.
To reduce the risk of electrical shock, do not remove the cover or the back. No user-service­able parts are inside. Refer servicing to qualified personnel or contact the Pelco Customer Service Department for assistance. Refer to the
Clean the cabinet with a cloth slightly dampened with mild household detergent only. Use a soft cloth for drying. Some household aerosol sprays, cleaning agents, solvents, or polishes may damage the cabinet finish. Never use strong solvents such as thinner or benzene.

SPECIFICATIONS

ELECTRICAL
Input Voltage: 110-240 VAC, 50/60 Hz
Power Consumption: 70 watts
Horizontal Resolution: 420 lines (center)
Picture Tube: 21.0 inches (53.34 cm) measured diagonally
Viewable Picture Size: 20.5 inches (52.07 cm) measured diagonally
300 lines (corners)
Warranty and Return Information
section.
Input Signal: Composite video, negative sync
Terminals
Video Input Level/ Impedance: 1.0 Vp-p/75 ohms Video Output Level/ Impedance: 1.0 Vp-p/75 ohms Audio Input Level/ Impedance: 0.3 Vrms/25K ohms (over) Audio Output Level/ Impedance: 0.3 Vrms/4.7K ohms (under)
Subcarrier Frequency Sync Range: 3.579549 MHz ±200 Hz
High Voltage: 25 ±1.2 kV
GENERAL
Connectors
Camera Input/ Video Output: BNC S-VHS Input: 4-pin mini DIN Audio Input/ Output: RCA
AC Power Cord: One power cord with grounded plug for 120 VAC
Y: 1.0 Vp-p C: 0.286 Vp-p
4.433619 MHz ±200 Hz at room temperature
One “Euro”-style grounded power cord for 230 VAC
6 Pelco Manual C1959M (6/99)
Construction
Monitor: Steel cabinet Bezel Rack Mount: Steel
Finish
Monitor: Black with black bezel around screen Bezel Rack Mount: Black
Dimensions
Monitor: See Figure 7 Bezel Rack Mount: See Figure 8
Unit Weight: 52 lb (23.6 kg)
ENVIRONMENTAL
Operating Temperature: 32° to 106°F (0° to 41°C) Humidity: 10% to 95% (non-condensing)
(Design and product specifications subject to change without notice.)
18.9
(48.0)
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES
18.9
(48.0)
17.2
(43.7)

Figure 7. PMC21A Dimension Drawing

19.22
(48.82)
18.36
(46.63)
19.00
(48.26)
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES

Figure 8. Bezel Rack Mount Dimension Drawing

Pelco Manual C1959M (6/99) 7
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
• Three years on Genex
• Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty.
•Two years on standard motorized or fixed focal length lenses.
•Two years on Legacy fixed dome products.
•Two years on Spectra continuous motion applications.
•Two years on Esprit
• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.
®
Series products (multiplexers, server, and keyboard).
®
, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
®
, Esprit®, ExSite™, and PS20 scanners, including when used in
®
and WW5700 Series window wiper (excluding wiper blades).
Series distributed network-based video products.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
REVISION HISTORY
Manual # Date Comments
C1959M 6/99 Original version.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 1999, Pelco. Endura and ExSite are trademarks of Pelco.
All rights reserved.
8 Pelco Manual C1959M (6/99)
Loading...