Pelco c1949m User Manual

C1949M (5/99)
Bezel Rack Mount for the
PMC21A 21-Inch Color Monitor

®

3500 Pelco Way
Clovis, CA 93612-5699
USA

In North America & Canada:
Tel [phone]
FAX [phone]

International Customers:
Tel [phone]
FAX [phone]

www.pelco.com

CAUTION:

Do not
install this monitor in a
location having exces-

sive heat or in any way that ob­structs the ventilation openings
in the cabinet. Premature com­ponent failure or cabinet dam­age may result.

NOTE:

Installation of the moni­tor and rack mount into the con­sole may require two persons.

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should be done by qualified installation and service personnel
only.

2. Installation should be done according to all local and national electrical and mechanical
codes, using only approved materials.

3. Use only installation methods and materials capable of supporting four times the maxi­mum specified load.

Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.

INSTALLATION

The bezel rack mount is provided as a standard accessory for the PMC21A color monitor. The
rack mount is constructed of steel, has a black finish, and occupies 11 rack unit spaces. It is
supplied with eight flat-head screws to attach the rack mount to the monitor and four 10-32
screws to attach the rack mount to a console.

1. Slide the bezel rack mount onto the monitor from the rear and attach it to the monitor with
the eight flat-head screws provided.

2. Place the PMC21A monitor and rack mount into the console, align the mounting holes of
the rack mount with the mounting holes in the console, and insert and tighten the four 10­32 screws provided. The face of the monitor protrudes approximately 4.8 inches (12.2 cm)
from the front of the console.

3. For the remainder of the monitor installation instructions, follow the procedures in the
installation/operation manual for the monitor.

FLATHEAD SCREW (8)

BEZEL RACK
MOUNT

PMC21A MONITOR

Figure 1. Rack Mount Installation

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

• Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.

•Two years on standard motorized or fixed focal length lenses.

•Two years on Legacy
fixed dome products.

•Two years on Spectra
continuous motion applications.

•Two years on Esprit

• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.

®

Series products (multiplexers, server, and keyboard).

®

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

®

, Esprit®, ExSite™, and PS20 scanners, including when used in

®

and WW5700 Series window wiper (excluding wiper blades).

™

Series distributed network-based video products.

18.36

(46.63)

19.00

(48.26)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;

ALL OTHERS ARE INCHES.

Figure 2. Rack Mount Dimension Drawing

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization number (RA), and provide the following
information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.

Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at
[phone] or [phone] to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

19.22

(48.82)

REVISION HISTORY

Manual # Date Comments

C1949M 5/99 Original version.

Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 1999, Pelco.
Endura and ExSite are trademarks of Pelco. All rights reserved.