Pelco C1925-PP, C1906-PP, C1925, C930M-E, C19125 User Manual 2

®
C1906, C1925, C19125,
C1906/PP and C1925/PP
Pre-wired Interconnecting
Inverting Cables
Installation/Operation Manual
Amended 1/96
PELCO • 3500 Pelco Way, Clovis, CA 93612-5699 • (559) 292-1981 • (800) 289-9100
FAX (800) 289-9150 or (559) 292-3827
TABLE OF CONTENTS
Section Page
1.0 WARNINGS ........................................................................................................................................1
2.0 SCOPE ............................................................................................................................................... 2
3.0 DESCRIPTION ................................................................................................................................... 2
3.1 MODEL NUMBERS .....................................................................................................................2
4.0 SPECIFICATIONS .............................................................................................................................. 2
5.0 INSTALLATION .................................................................................................................................. 2
6.0 OPERATION ...................................................................................................................................... 2
5.1 SYSTEM TEST ............................................................................................................................2
7.0 TROUBLE SHOOTING GUIDELINES ............................................................................................... 3
8.0 SCHEMATICS ....................................................................................................................................3
9.0 WARRANTY AND RETURN INFORMATION .....................................................................................6
LIST OF ILLUSTRATIONS
Figure Page
1 C1906, C1925, and C19125 Wiring Diagram ..................................................................................... 3
2 C1906/PP and C1925/PP Wiring Diagram .........................................................................................4
3 C1906/PP and C1915/PP Wiring Diagram For Use with Upright Pan/Tilts Only ................................5
REVISION HISTORY
Manual # Date Comments
C930M No date. Original version.
C930M 8/90 Rev. A. Revised to include preset models C1906/PP and C1925/PP.
C930M 4/91 Rev. B. Figure 2 revised; Figure 2A added as an addendum.
C930M-C 1/95 Figures 2 and 2A (now Figure 3) revised to show correct pinouts for
pins 17 and 18 on the 28-pin connector (pan/tilt functions). Also, Fig­ures 1-3 revised to show new wire colors (see pins 5, 8, 11 and 13 on the 14- or 28-pin connector).
C930M-D 9/95 Rev. D. Revised wire colors for pins 11 and 13 on Figures 1-3.
C930M-E 12/95 Rev. E. Revised Figure 2, pin 17 and 18 colors and functions.
®Pelco and the Pelco logo are registered trademarks of Pelco. ©Copyright 1995, Pelco. All rights reserved.
8 Pelco Manual C930M-E (12/95)
ii
INSTALLATION AND OPERATION MANUAL MODELS C1906, C1925, C19125, C1906/PP, AND C1925/PP PRE-WIRED INTERCONNECTING INVERTING CABLES
1.0 WARNINGS
1. Installation and Servicing should only be done by Qualified Service Personnel.
2. The installation shall be done in accordance with all local and national electrical and me­chanical codes utilizing only approved mate­rials.
3. Unless the cable is specifically marked “WA” (for use in wet locations), the cable is designed for indoor use only and it must not be installed where exposed to rain and moisture.
2.0 SCOPE
The information within this manual covers the installa­tion and operation of the C1906, C1925, C19125, C1906/PP, and C1925/PP pre-wired interconnecting inverting cables.
Please thoroughly familiarize yourself with the infor­mation in this manual prior to installation and opera­tion.
3.0 DESCRIPTION
The C1906, C1906/PP, C1925, C1925/PP and C19125 are pre-wired cables designed for interconnecting Pelco’s Coaxitron® receiver/driver with various Pelco domes or any inverted PT180-24P/PT280-24P pan/tilt application as listed below.
C1906, C1925, C19125
Domes: ED2820, ED2820-3, ED2820-SL,
ED2920, ED2920-SL, SB2800, SB2800-2, SB2800-SL, SB2800-SL-2, SB2801 SS3000, SS3002
Pan/Tilts: PT180-24P, PT180-24SL,
PT280-24P, PT280-24SL
C1906/PP, C1925/PP
Domes: ED2820-PP, ED2820SL/PP,
ED2820-3SL/PP, SB2800/PP, SB2800-SL/PP
Pan/Tilts: PT180-24P/PP,
PT280-24P/PP, PT280-24SL/PP
3.1 MODEL NUMBERS
C1906 6 ft (1.83 m), pre-wired intercon-
necting inverting cable. (UL)
C1925 25 ft (7.62 m), pre-wired intercon-
necting inverting cable. (UL)
C19125 125 ft (38.1 m), pre-wired inter-
connecting inverting cable. (UL)
C1906/PP 6 ft (1.83 m), same as C1906 but
for PP models. (UL)
C1925/PP 25 ft (7.62 m), same as C1925 but
for PP models. (UL)
Pelco Manual C930M-E (12/95) 1
4.0 SPECIFICATIONS
6.0 OPERATION
ELECTRICAL
Connectors:
Receiver side CPC, 37 sockets Pan/tilt side CPC, 14 pins
CPC, 28 pins (PP models)
Cable: 12 conductor with shield, 20 Awg
RG59/U
GENERAL
Cable length:
C1906 6 ft (1.83 m) long C1925 25 ft (7.62 m) long C19125 125 ft (38.1 m) long C1906/PP 6 ft (1.83 m) long C1925/PP 25 ft (7.62 m) long
Maximum Wire Temperature: 140° F (60° C)
5.0 INSTALLATION
1. Run the cable from the Coaxitron® receiver/driver to the pan/tilt. Be careful not to abrade or cut the jacket on the cable since this could result in a short.
By using the controller, you should be able to control the pan and tilt functions of the pan/tilt and the focus, iris, and zoom functions of the motor operated lens.
6.1 SYSTEM TEST
Using the controller, operate the following functions and verify correct operation of each function:
1. Pan Left
2. Pan Right
3. Tilt Up
4. Tilt Down
5. Zoom Wide
6. Zoom Telephoto
7. Iris Open
8. Iris Closed
9. Focus Near
10. Focus Far
If all the above functions operate correctly, the instal­lation process is complete. If all the above functions do not operate correctly, refer to Section 7.0, Troubleshoot­ing Guidelines.
For PP models — check all of the above again using a set preset location.
2. Connect the 37-pin CPC connector to the Coaxitron® receiver/driver.
3. Connect the 14-socket CPC connector (28-pin PP models) to the pan/tilt unit.
4. Operate the control unit and determine correct op­eration of the unit. If the unit fails to operate cor­rectly, refer to the troubleshooting guidelines out­lined in Section 7.0.
2 Pelco Manual C930M-E (12/95)
7.0 TROUBLESHOOTING GUIDELINES
1. If none of the functions in Section 6.1 operate cor­rectly, check the connection of the CPC connec­tors to the Coaxitron® receiver/driver and pan/tilt.
2. If the connections are loose, tighten the lock ring on the CPC connectors and start the system test procedure in Section 6.1.
3. If the connections are tight, check the Coaxitron receiver/driver to determine if it is operating cor­rectly. If the Coaxitron® receiver/driver is operat­ing correctly, there may be a problem with the cable and Pelco’s Technical Assistance Program (TAP) should be contacted for further technical trouble­shooting aid. To contact the TAP line, call 1-800-
289-9100.
NOTE: These cables are designed for use
in inverted applications. If you wish to modify the cable for upright operation, pins 3 and 7 (pan) and pins 5 and 6 (tilt) need to be re­versed on the 14- or 28-pin connector (pan/ tilt side). The problem can be corrected in the field with a CPC pin/socket extracting tool by simply exchanging the pins for these func­tions. If you do not have the necessary tool,
®
contact Pelco for a R/A number to exchange the cable.
8.0 SCHEMATICS
Refer to Figures 1-3 for wiring diagrams of the pre­wired cables.
Figure 1. C1906, C1925, and C19125 Wiring Diagram
Pelco Manual C930M-E (12/95) 3
Figure 2. C1906/PP and C1925/PP Wiring Diagram
4 Pelco Manual C930M-E (12/95)
Figure 3. C1906/PP and C1925/PP Wiring Diagram for Use with Upright Pan/Tilts Only
Pelco Manual C930M-E (12/95) 5
9.0 WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
• Three years on Genex
keyboard).
• Three years on Camclosure
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty.
• Two years on standard motorized or fixed focal length lenses.
• Two years on Legacy
DF5/DF8 Series fixed dome products.
• Two years on Spectra
ing when used in continuous motion applications.
• Two years on Esprit
wiper blades).
Eighteen months on DX Series digital video recorders, NVR300
Series network video recorders, and Endura network-based video products.
• One year (except video heads) on video cassette recorders (VCRs).
Video heads will be covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in
continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289­9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice
number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned. Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
®
Series products (multiplexers, server, and
®
and fixed camera models, except the
®
, CM6700/CM6800/CM9700 Series matrix, and
®
, Esprit®, ExSite™, and PS20 scanners, includ-
®
and WW5700 Series window wiper (excluding
Series distributed
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following: If the goods are to be sent by a COURIER SERVICE, send the goods to:
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699
Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA
Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933
®
Pelco
300 West Pontiac Way, Clovis, CA 93612-5699
(559) 292-1981 • (800) 289-9100
FAX (800) 289-9150 or (559) 292-3827
(Product specifications subject to change
without notice.)
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco.
© Copyright 1995, Pelco. All rights reserved.
C930M-D
6 Pelco Manual C930M-E (12/95)
Loading...