Pelco C1662M-A User Manual

INSTALLATION

TW3000P Series
Passive Multichannel
Video Transceivers

C1662M-A (1/06)

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.

9. Only use attachments/accessories specified by the manufacturer.

10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.

11. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.

12. Apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases shall be placed on the apparatus.

13. Installation should be done only by qualified personnel and conform to all local codes.

14. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P
enclosure, it is designed for indoor use only and it must not be installed where exposed
to rain and moisture.

15. Use only installation methods and materials capable of supporting four times the
maximum specified load.

Only use replacement parts recommended by Pelco.

2 C1662M-A (1/06)

Description

The TW3000 Series multichannel video transceiv ers can transmit multiple video signals over unshielded
twisted pair (UTP) cable. The receivers are passive and require no power. The transceivers are available
with 8, 16, or 32 channels and can be mounted into an industry standard 19-inch (48.26 cm) wide
equipment rack. Each model has built-in surge suppression.

The transceivers can be used at the camera and/or monitoring location. They allow for easy
connectivity with any video source or destination device, such as cameras, monitors, and matrix
switchers. These multichannel transceivers will transmit video (color/black-white) and Coaxitron
(up-the-coax) PTZ control signals on the same pair of UTP wires.

MODELS

TW3008P 8-channel passive video transceiver
TW3016P Same as TW3008, except 16 channels
TW3032P Same as TW3008, except 32 channels

®

C1662M-A (1/06) 3

BACK VIEW



1

2345678

 

2345678 9101112131415

1

12 34 56 78 9101112131415

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

Figure 1. Back View of TW3008P, TW3016P, TW3032P

1

34 5678

2

1

3 4 5 6 7 8 9101112 13141516

2

16



123 4 5 6 7 8 9101112 13141516

16

17

19 20 21 22 23 24 25 26 27 28 29 30 31 32

18

32



TW3008P

TW3016P

TW3032P



Rack Ears: Allow mounting into an industry standard 19-inch wide equipment rack.



Thumbscrews: Allow back panels to be removed.



Panel with Connectors: The TW3008P and TW3016P have one blank panel.



BNC Connectors: The TW3008P, TW3016P, and TW3032P have 8, 16, and 32 BNC connectors,

respectively.



Screw Terminal Connectors: The TW3008P, TW3016P, and TW3032P have 2, 4, and 8 screw

terminal connectors, respectively. Each screw terminal connector allows for the connection of
four UTP wire pairs.

4 C1662M-A (1/06)