Pelco 12FA4.5C, 13FA8, 12FA6C, 12FA12C, 13FA2.3 User Manual

...

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series ﬁber optic products.

• Three years on Genex

• Three years on Camclosure® and ﬁxed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a ﬁve-year warranty.

•Two years on standard motorized or ﬁxed focal length lenses.

•Two years on Legacy

•Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications.

•Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura™ Series distributed network-based video products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of proﬁt and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA

Series products (multiplexers, server, and keyboard).

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series ﬁxed dome products.

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933

Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 • USA www.pelco.com In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150 ® Pelco and the Pelco logo are registered trademarks of Pelco. • © Copyright 1999, Pelco. All rights reserved.

C747M (5/99) Fixed Focal Length Lenses

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Servicing should only be done by qualified service personnel.

2. Only use replacement parts recommended by Pelco.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

DESCRIPTION

Lenses in the fixed focal length category offer a selection of imager format optics in various focal lengths.

The 1/2-inch imager format lenses are available in both C- and CS-type mounts, depending upon the model used, while the 2/3-inch lenses are available in C-type mounts only. A 5-mm spacer (commonly referred to as a C/CS-mount adapter and available from Pelco as the PCMA40 lens adapter) may be used to make a C-type lens compatible to a CS-type camera. However, CS-type lenses are not compatible to C-mount cameras. The CS lenses require fewer glass elements to focus at a shorter distance, while not affecting picture quality. The entire series of 1/3-inch imager format lenses come with CS-type mounts.

All fixed focal length lenses feature high-resolution power in a compact body.

The FA series fixed focal length lenses have a manual iris and manual focus.

The FD series fixed focal length lenses have a direct-drive auto iris and manual focus, while the FV series have a video-drive auto iris. Both the FD and FV series have an industrystandard square four-pin connector that plugs directly into the camera receptacle. In addition, all auto-iris lenses include a spot filter.

MODELS

Fixed focal length lenses with manual iris and manual focus. 12FA3.5C 13FA2.3 23FA8 12FA4.5C 13FA2.8 23FA12 12FA6C 13FA4 23FA16 12FA12C 13FA8 23FA25 Suffix “C” indicates 1/2-inch lenses having a C-type mount.

Fixed focal length lenses with direct-drive auto iris and manual focus. 13FD2.3 (CE) 13FD4 (CE) 13FD2.8 (CE) 13FD8 (CE)

Fixed focal length lenses with video-drive auto iris and manual focus. 12FV3.5 (CE) 12FV6 (CE) 13FV2.3 (CE) 23FV8 (CE) 12FV4C (CE) 12FV6C (CE) 13FV2.8 (CE) 23FV12 (CE) 12FV4.5 (CE) 12FV12 (CE) 13FV4 (CE) 23FV16 (CE) 12FV4.5C (CE) 12FV12C (CE) 13FV8 (CE) 23FV25 (CE) Suffix “C” indicates 1/2-inch lenses having a C-type mount.

INSTALLATION

LENS AND CONNECTOR WIRING DIAGRAMS

Remove the dust covers from the lens. Remove any dust with a soft brush or clean compressed air.

The lens is installed by carefully threading it clockwise onto the mount of the CCTV camera until fully seated. If the lens has a coupling ring, tighten it against the camera. Use a C/CS-mount adapter if attaching a C-type lens to a CS-type camera. The PCMA40 adapter is available from Pelco.

If your lens has an a direct- or video-drive auto iris, plug the electrical connector directly into the camera auto-iris DC drive or auto-iris video drive socket, whichever is applicable.

Follow the camera operating instructions for iris and focus adjustments.

Lenses having ALC and LEVEL variable resistors may need the following adjustments:

(1) ALC (Light Metering)

This function allows a variable selection of light metering between average (A) and peak (P). Turn the variable resistor on the lens body with a precision screwdriver (not provided) until suitable exposure is obtained.

(2) LEVEL (Image Signal)

This feature helps to adjust the brightness of the images projected on the TV monitor. When it is necessary to make a correction due to camera characteristics or lighting conditions, adjust the variable resistor on the lens body with a precision screwdriver (not provided) until optimum level is obtained.

ALC & Level Adjustment Screws

Pelco FD Type Lenses

TO CAMERA AUTO-IRIS SOCKET, DC DRIVE

4 2

3 1

AUTO-IRIS PLUG PIN-OUT

(REAR OF PLUG, SOLDER LUGS)

SQUARE

CONNECTOR

4-PIN

DRIVE ( + )

DRIVE ( – )

CONTROL ( + )

CONTROL ( – )

RED

BLACK

YELLOW

GREEN

4-CONDUCTOR CABLE

Pelco FV Type Lenses

TO CAMERA AUTO-IRIS SOCKET, VIDEO DRIVE

4 2

3 1

AUTO-IRIS PLUG PIN-OUT

(REAR OF PLUG, SOLDER LUGS)

4-PIN

SQUARE

CONNECTOR

DC+ (8-16)

GROUND

VIDEO

REMOTE

RED

BLACK

WHITE

GREEN

4-CONDUCTOR CABLE

AUTO-

IRIS

CIRCUIT

SPECIFICATIONS

Technical specifications may be obtained from Pelco by any of the following methods:

IRIS

ROUTINE SERVICING

Never touch the surface of either lens.

Remove dust from the lens by using a soft brush or clean compressed air. Avoid touching the lens surface during handling.

To remove fingerprints or oil stains from the lens surface, use lens cleaning paper or a clean cotton cloth with a little cleaning liquid. Then, wipe off the stains using a light circular motion, starting from the center of the lens surface. Wipe the lens body with a silicon cloth. Do not use any organic solvents such as thinner or benzene.

• Product Specification Book

• Pelco’s BOSS® Software

• www.pelco.com