Peerless Lighting TLWA User Manual

Type: ________________________

Tulip Wall Asymmetric

Project: ______________________

Direct T8

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Wall Mount TLWA

LAMPING OPTIONS

TLWA D

4”

7

⁄16”

3 5⁄8”

TLWA X

21”

4”

3 5⁄8”

SPECIFICATIONS

Construction

Extruded aluminum housing forms a 3 5⁄8” x 4”
curved channel. Die-cast aluminum end caps
mechanically attach with no exposed fasteners.
Extended arm mount (option “X”) is extruded
aluminum and die-cast aluminum, extending 21”.

Reflectors

High reflectance white painted reflector system.

Shielding

Arc-shaped, parabolic low iridescent semi-specular
or white painted aluminum louver.

Finish

Satin anodized or white low gloss paint. With satin
anodized option, housing is satin anodized and end
caps are painted to match. Custom colors available,
consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wire s. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’, 8’, and 12’ lengths in a single section. For total
luminaire length, add 3⁄8” for each end cap. Using
internal joiners, 4’, 8’, and 12’ sections can be joined
to form longer length luminaires. Individual 2’ and 3’
luminaires also available.

Eco-friendly Packaging

100% post-consumer recycled cardboard box,
100% recycled cardboard cradles and kraft paper
tape. Biodegradable, protective luminaire bag.

CATALOG NUMBER

Examples: TLWA D 1 32 SSB 8FT R8 120 GEB10 1SE EC SCT LP830 C100  — TLWA X 1 32 WPB 8FT R8 120 GEB10 1SE EC SCT L/LP C041

__________ __________ __________ __________ __________ _________ __________ __________ __________ __________

Luminaire

TLWA

______________ ________________ ________________ ______________ _________________________________

Emergency Type

(Blank) None
EC Emergency circuit
EL1 Emergency battery pack
EN1 Emergency battery pack

Notes:

1 Not available in 347V
2 Emergency type is installed in last 4’ of luminaire sections.

Separate feed required unless ELS or ELS2 is specified

Mounting
Type

D Wall

spacer

X 21”

extended
arm mount

2

w/night light circuit

# of
Lamps in
Cross

Lamp Type

32 32W T8

Section

1

Switching

SCT Single circuit

Shielding

SSB Semi specular

bae

WPB White painted

bae

Lamp Color

L/LP No lamp
L/LPE No lamp. Wired for

energy saving lamps.

LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

Reference Lamp Chart on
website or consult factory for
other options.

Luminaire
Row
Length

X FT

(4’ increments)

Maximum
Section
Length

R2 2’ individual unit
R3 3’ individual unit
R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Finish

C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish

Voltage

120
277
347

Ballast Type

GEB10 <10% THD Electronic
ADEZ1, Advance Mark 10 dim
DMHL3D1 Lutron Hi-Lume dim
ADZT1 Advance Mark 7 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

Options

DL Damp location label
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
NYC New York City code

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.

TLWA  Tulip Wall Asymmetric

Direct T8

1

Type: ________________________

Tulip Wall Asymmetric

Direct T8

Wall Mount TLWA

MOUNTING DETAIL (WALL SPACER “D”)

#10-24 SET SCREWS

(4 PER SUPPORT)

3

2

/4"

7

/16"

WEIGHTS & SUPPORT SPACING

STANDARD SECTIONS

12 LBS

24 LBS

36 LBS

8”

8”

8”

ELEVATION

2’-8”

4’-0 3⁄4” O.A.

6'-8"

8’-0 3⁄4” O.A.

5’-4”

MTG HOLES FOR 1/4" BOLT

5

WALL BRACKET

3

⁄8” end cap

1

/2"

12’-0 3⁄4” O.A.

3

⁄8” end cap

5’-4”

Key:

Suppor t location

Standard feed location

EM feed location

•

Project: ______________________

3

⁄8” end cap

CONFIGURATIONS

Mitered connectors for inside and outside corners available for wall configurations.
Reference Pattern Connector Guide for additional details.

PHOTOMETRICS

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

Actual performance may dier as a result of end-user environment and application.

1-LAMP T8

54.9% eciency
1564 delivered lumens

0.0% up / 100.0% down

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.

TLWA  Tulip Wall Asymmetric

Direct T8

2