Peerless Lighting TLML User Manual

Type: ________________________

Tulip Softshine

Direct T5/T5HO

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Suspended TLML

Project: ______________________

LAMPING OPTIONS

TLML

4”

3 5⁄8”

SPECIFICATIONS

Construction

Extruded aluminum housing forms a 3 5⁄8” x 4”
curved channel. Die-cast aluminum end caps
mechanically attached with no exposed fasteners.

Reflectors

High reflectance white painted reflector system.

Shielding

Softshine™ high performance lens controls light
distribution. Uniform luminance along the length of
the lens is achieved with staggered lamps.

Finish

Satin anodized or white low gloss paint. With satin
anodized option, housing is satin anodized and end
caps are painted to match. Custom colors available,
consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wire s. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

Stand alone sections are 3’10” (R4), 7’3” (R8),
and 10’8” (R12). Rows are comprised of starter,
joiner and end sections of various lengths. Refer to
planning guide for details. For total luminaire length,
add 3⁄8” for each end cap or 1” for each sculptured
end cap (SCEP) when F3 stem mount or option
ELS2 is specified.

Eco-friendly Packaging

100% post-consumer recycled cardboard box,
100% recycled cardboard cradles and kraft paper
tape. Biodegradable, protective luminaire bag.

CATALOG NUMBER

Examples: TLML 1 28T5 SSH 34FT7IN R8 120 GEB10 SCT LP835 F1/18 C100 — TLML 1 28T5 SSH 41FT5IN R8 277 GEB10 1SE EC SCT LP835 F1/24C041

__________ __________ __________ __________ _________ __________ __________ __________ __________

Luminaire

TLML

______________ ________________ ________________ ______________ ______________ ______________ _________________________________

Emergency Type

(Blank) None
EC Emergency

1

EL

EN

Notes:

1 Not available in 347V
2 Not available with 28T5 lamps

# of
Lamps in
Cross
Section

1

circuit

Emergency

battery pack

1

Emergency

battery pack
w/night light
circuit

Lamp Type

28T5 28W T5
54T5HO 54W T5HO

3

Switching

SCT Single circuit

Shielding

SSH Softshine

Lamp Color

L/LP No lamp
LP830 3000k 80+ CRI
LP835 3500k 80+ CRI
LP841 4100k 80+ CRI

Available with T5 only:

3000K 80+

LP830P

3500K 80+

LP835P

4100K 80+

LP841P

Reference Lamp Chart on
website or consult factory
for other options.

3 Emergency type is installed in last 4’ of luminaire

sections. Separate feed required unless ELS or ELS2 is

Luminaire Row Length

3FT10IN Individual (R4)

lens

7FT3IN Individual (R8)

10FT8IN Individual (R12)

14FT1IN

17FT6IN

20FT11IN

24FT4IN
27FT9IN

31FT2IN

CRI Premier

CRI Premier

CRI Premier

44FT10IN

Mounting Type /

F1/ T-bar ceiling (universal

T-bar ceiling (UMB with

F1A/

Hard ceiling (horizontal

F2/

4

/ Rigid stem

F3

34FT7IN
38FT0IN

48FT3IN

58FT6IN

41FT5IN

61FT11IN
65FT4IN
68FT9IN

51FT8IN

72FT2IN

mounting bracket)

integrated J-box)

J-box)

Maximum
Section
Length

75FT7IN

79FT0IN

55FT1IN

82FT5IN

85FT10IN

89FT3IN
92FT8IN

99FT6IN

specified

4 1” sculptured end cap (SCEP) used

96FT1IN

Overall
Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall
suspension is
measured from
ceiling to bottom
of luminaire.

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Finish

C041 White white

C100

C099

Voltage

120
277
347

(low gloss)

Satin anodized

finish

Custom finish

Ballast Type

GEB10 <10% THD Electronic

1,2

ADEZ

Advance Mark 10 dim

DMHL3D1 Lutron Hi-Lume dim

1,2

OSDIM

Osram 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy (not available

with F3)

Chicago plenum (available with F1A only)

CP
DL Damp location label
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared

neutral

4

Emergency through wiring w/single feed, separate

ELS2

neutrals

Fusing (fast blow)

GLR
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per row/zone
NYC New York City code
OJB Oset junction box
SLP Sloped ceiling (for 10-45°, must be specified with

F2, ACG and OJB options)

Integrated sensor; choose options and obtain code

XXXX

on page 2

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.

TLML  Tulip Softshine

Direct T5/T5HO

1

90 270

500

1000

1500

2000

Type: ________________________

Tulip Softshine

Project: ______________________

Direct T5/T5HO

Suspended TLML

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

3

7’-3”

3

⁄4” O.A.

⁄8” end cap

12 LBS

24 LBS

I

4

I

8

3’-10

3

⁄4” O.A.

7’-3

3’-10”

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

3

⁄8” end cap

3

⁄8” end cap

36 LBS

12

10’-8

3

⁄4” O.A.

I

10’-8”

PLAN VIEW

CONFIGURATIONS

Mitered “L”, “X” and “T” connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.

PHOTOMETRICS

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

Actual performance may dier as a result of end-user environment and application.

1-LAMP T5HO

66.4% eciency
3321 delivered lumens

0.0% up / 100.0% down

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.

TLML  Tulip Softshine

Direct T5/T5HO

2