Peerless Lighting PRM4 User Manual

Type: ________________________

Prima I/D

Indirect-Direct T5/T5HO

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Suspended PRM4

Project: ______________________

LAMPING OPTIONS

PRM4 - 1 PRM4 - 2 PRM4 - 3

3”

9”

9”

3”

3”

9”

SPECIFICATIONS

Construction

9” x 3” one-piece cold-rolled steel housing with flat
end plate.

Reflectors

Die-formed highly reflective white or specular
reflector.

Shielding

Semi-specular parabolic aluminum baes.

Finish

Fine-textured, white paint or silver paint to match
anodized aluminium are standard. Custom colors
available, consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’ 1⁄4”, 8’ and 12’ lengths in a single section for
exact suspension spacing of 4’, 8’ and 12’. For total
luminaire length add 1⁄16” for each end cap. Using
internal joiners, 4’, 8’ and 12’ sections can be joined
to form longer-length luminaires.

CATALOG NUMBER

Examples: PRM4 1 54T5HO SPR OPD WPB 40FT R12 120 GEB10 2SE EL SCT LP841 F1/24 C110 — PRM4 2 54T5HO WHR OPD SSB 12FT R8 277 GEB10 DCT LP830 F2/15 C518 GLR

__________ __________ __________ __________ __________ __________ _________ __________ __________ __________

28W T5

Luminaire

PRM4

# of
Lamps in
Cross
Section

1
2
3

______________ ________________ __________ ________________ ______________ ______________ ______________ _________________________________

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Notes:

1 Not available in 347V
2 Not available with 28T5 lamps

28T5
54T5HO 54W T5HO

Emergency Type

(Blank) None
EC Emergency

circuit

1

Emergency

EL

battery pack

1

Emergency

EN

battery pack
w/night light
circuit

3 EL and EC are installed in last 4’ of luminaire sections.

Separate feed required unless ELS or ELS2 is specified

3

Switching

SCT Single

Dual

DCT

Reflector

WHR White

Reflector
(Standard)

Specular

SPR

Reflector

Lamp Color

L/LP No lamp

circuit

LP830 3000k 80+ CRI
LP835 3500k 80+ CRI

circuit

LP841 4100k 80+ CRI

Available with T5 only:
LP830P

LP835P

LP841P

Reference Lamp Chart on
website or consult factory
for other options.

Shielding

OPD Bae

w/std
brightness
opal
diuser
overlay

3000K 80+

CRI Premier

3500K 80+

CRI Premier

4100K 80+

CRI Premier

Bae

SSB Semi-

White

WPB

specular
bae

painted
bae

Luminaire
Row
Length

X FT

(4’ increments)

Mounting Type /

F1/ T-bar ceiling (universal

mounting bracket)

T-bar ceiling (UMB with

F1A/

integrated J-box)

Hard ceiling (horizontal

F2/

J-box)

Rigid stem

F3/

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Overall
Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall
suspension is
measured from
ceiling to bottom
of luminaire.

Voltage

120
277
347

Finish

C110 Painted

aluminum
(low gloss)

White (fine-

C518

textured low
gloss)

Custom

C099

finish

Ballast Type

GEB10 <10% THD Electronic

1,2

ADEZ

Advance Mark 10 dim

DMHL3D1 Lutron Hi-Lume dim

1,2

OSDIM

Osram 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy (not

available with F3)

Chicago plenum (available with F1A only)

CP
DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed,

shared neutral

Emergency through wiring w/single feed,

ELS2

separate neutrals

Fusing (fast blow)

GLR
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per row/zone
NYC New York City code
OJB Oset junction box
SLP Sloped ceiling (for 10-45°, must be specified

with F2, ACG and OJB options)

Integrated sensor; choose options and obtain

XXXX

code on page 2

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Prima” are registered trademarks of Acuity Brands Lighting.

PRM4  Prima I/D

Indirect-Direct T5/T5HO

1

Type: ________________________

Prima I/D

Project: ______________________

Indirect-Direct T5/T5HO

Suspended PRM4

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

25 LBS

44 LBS

4’-0 3⁄8”

4’-0

1

⁄2” O.A.

8’-0

8’-0

1

⁄16” standard flat end plates

1

⁄8”

1

⁄4” O.A.

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

60 LBS

PLAN VIEW

CONFIGURATIONS

Aluminum cast corners available for suspended configurations.
Reference Pattern Connector Guide for additional details.

PHOTOMETRICS

12’-0”

1

⁄8” O.A.

12’-0

Actual performance may dier as a result of end-user environment and application.

1-LAMP T5HO WITH OPD

92.2% eciency
4609 delivered lumens

88.9% up / 11.1% down

2-LAMP T5HO WITH OPD

86.8% eciency
8675 delivered lumens

88.1% up / 11.9% down

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Prima” are registered trademarks of Acuity Brands Lighting.

PRM4  Prima I/D

Indirect-Direct T5/T5HO

2