Peerless Lighting PRM1 User Manual

Type: ________________________

Prima

Indirect T8

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Suspended PRM1

Project: ______________________

LAMPING OPTIONS

PRM1 - 1 PRM1 - 2 PRM1 - 3

3”

9”

9”

3”

3”

9”

PRM1 - 4

9”

SPECIFICATIONS

Construction

9” x 3” one-piece cold-rolled steel housing with flat
end plate.

Reflectors

Die-formed highly reflective white or specular
reflector.

Finish

Fine-textured, white paint or silver paint to match
anodized aluminium are standard. Custom colors
available, consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’, 8’, and 12’ lengths in a single section for exact
suspension spacing of 4’, 8’, and 12’. For total
luminaire length add 1⁄16” for each end cap. Using
internal joiners, 4’, 8’, and 12’ sections can be joined
to form longer-length luminaires.

3”

CATALOG NUMBER

Examples: PRM1 1 32 WHR 40FT R12 120 GEB10 2SE EL SCT LP835 F1/24 C518 — PRM1 3 32 SPR 12FT R8 277 GEB10 DCT LP835 F2/15 C518 GLR

__________ __________ __________ __________ _________ __________ __________ __________ __________ __________

Luminaire

PRM1

______________ ________________ ______________ ______________ ______________ _________________________________

Switching

SCT Single circuit
DCT Dual circuit

# of
Lamps in
Cross
Section

1
2
3
4

Lamp Color

L/LP No lamp
L/LPE No lamp. Wired

LP830
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

Reference Lamp Chart on
website or consult factory
for other options.

Lamp Type

32 32W T8

for energy saving
lamps.

3000K 80+ CRI

Reflector

WHR White

Reflector
(Standard)

Specular

SPR

Reflector

Luminaire
Row
Length

X FT

(4’ increments)

Mounting Type /

F1/ T-bar ceiling (universal

mounting bracket)

T-bar ceiling (UMB with

F1A/

integrated J-box)

Hard ceiling (horizontal

F2/

J-box)

Rigid stem

F3/

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Overall Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall suspension is
measured from ceiling to
bottom of luminaire.

Voltage

120
277
347

Ballast Type

GEB10 <10% THD Electronic
ADEZ1 Advance Mark 10 dim
DMHL3D1 Lutron Hi-Lume dim
ADZT1 Advance Mark 7 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

Finish

C110 Painted aluminum

White (fine-

C518

Custom finish

C099

(low gloss)

textured low
gloss)

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Emergency Type

(Blank) None
EC Emergency circuit
EL1 Emergency battery pack
EN1 Emergency battery pack

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy (not available with F3)
CP Chicago plenum (available with F1A only)
DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per row/zone
NYC New York City code
OJB Oset junction box
SLP Sloped ceiling (for 10-45°, must be specified with F2, ACG and

OJB options)

Integrated sensor; choose options and obtain code on page 2

XXXX

2

w/night light circuit

Notes:

1 Not available in 347V
2 EL and EC are installed in last 4’ of luminaire sections.

Separate feed required unless ELS or ELS2 is specified

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Prima” are registered trademarks of Acuity Brands Lighting.

PRM1  Prima

Indirect T8

1

Type: ________________________

Prima

Project: ______________________

Indirect T8

Suspended PRM1

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

25 LBS

44 LBS

4’-0 3⁄8”

4’-0

1

⁄2” O.A.

8’-0

8’-0

1

⁄16” standard flat end plates

1

⁄8”

1

⁄4” O.A.

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

60 LBS

PLAN VIEW

CONFIGURATIONS

Aluminum cast corners available for suspended configurations.
Reference Pattern Connector Guide for additional details.

PHOTOMETRICS

12’-0”

1

⁄8” O.A.

12’-0

Actual performance may dier as a result of end-user environment and application.

1-LAMP T8

89.8% eciency
2560 delivered lumens

100.0% up / 0.0% down

2-LAMP T8

86.2% eciency
4916 delivered lumens

100.0% up / 0.0% down

3-LAMP T8

84.8% eciency
7246 delivered lumens

100.0% up / 0.0% down

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Prima” are registered trademarks of Acuity Brands Lighting.

PRM1  Prima

Indirect T8

2