Peerless Lighting LLMS User Manual

Lightline Symmetric
Direct

Direct T5

Type: ________________________

Project: ______________________

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Surface LLMS

LAMPING OPTIONS

LLMS S

3

⁄8”

4 1⁄16”

3 5⁄8”

SPECIFICATIONS

Construction

Extruded aluminum housing forms a 3 5⁄8” x 4 1⁄16”
rectangular profile. Die-cast aluminum end caps
mechanically attach with no exposed fasteners.

Shielding

Arc-shaped, parabolic low iridescent semi-specular
or white painted aluminum louver.

Reflectors

High reflectance white painted reflector system.

Finish

Satin anodized finish consists of satin anodized
housing with end caps painted to match. Custom
colors available, consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’, 8’ and 12’ lengths in a single section for exact
suspension spacing of 4’, 8’, and 12’. For total
luminaire length, add 7⁄8” for each end cap. Using
internal joiners, 4’, 8’ and 12’ sections can be joined
to form longer rows.

CATALOG NUMBER

Examples: LLMS S 1 28T5 WPB 40FT R8 277 GEB10 1SE EC SCT LP835 C041

__________ __________ __________ __________ __________ _________ __________ __________ __________ __________

Luminaire

LLMS

Mounting Type

S Surface

# of Lamps in
Cross Section

1

Lamp Type

28T5 28W T5

Bae

SSB Semi

specular
bae

White

WPB

painted
bae

Luminaire
Row
Length

X FT

(4’ increments)

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Voltage

120
277
347

Ballast Type

GEB10 <10% THD Electronic
DMHL3D1 Lutron Hi-Lume dim

Reference Ballast Wizard on website
or consult factory for other options.

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

______________ ________________ ________________ ______________ _________________________________

Emergency Type

(Blank) None
EC Emergency circuit
EL1 Emergency battery pack
EN1 Emergency battery pack

w/night light circuit

Notes:

1 Not available in 347V 2 Emergency type is installed in last 4’ of luminaire sections.

2

Switching

SCT Single circuit

Separate feed required unless ELS or ELS2 is specified

Lamp Color

L/LP No lamp
LP830 3000k 80+ CRI
LP835 3500k 80+ CRI
LP841 4100k 80+ CRI

LP830P 3000K 80+

CRI Premier

3500K 80+

LP835P

CRI Premier

4100K 80+

LP841P

CRI Premier

Reference Lamp Chart on
website or consult factory
for other options.

Finish

C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish

Options

DL Damp location label
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
NEPP5D nLight enabled control module per row/zone
NYC New York City code
XXXX Integrated sensor; choose options and obtain code on page 2

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Lightline” are registered trademarks of Acuity Brands Lighting.

LLMS  Lightline Symmetric

Direct T5

1

Type: ________________________

Lightline Symmetric Direct

Project: ______________________

Direct T5

Surface LLMS

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Surface mount spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

7

8

12 LBS

24 LBS

36 LBS

⁄8”

7

⁄8”

8

7

⁄8”

8

PLAN VIEW

4 7⁄16”

4’-1

4 7⁄16”

7

4

⁄16”

2’-8”

3

⁄4” O.A.

7

⁄8” end cap

6’-8”

3

8’-1

⁄4” O.A.

5’-4” 5’-4”

3

12’-1

⁄4” O.A.

Network Type & Sensor Power Source (choose one)

Key:

Support location

Standard feed location

EM feed location

•

7

⁄8” end cap

7

⁄8” end cap

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Lightline” are registered trademarks of Acuity Brands Lighting.

LLMS  Lightline Symmetric

Direct T5

2