Peerless Lighting LL1M3 User Manual

Type: ________________________

Lightline Lightvent

Indirect T8

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Suspended LL1M3

Project: ______________________

LAMPING OPTIONS

LL1M3

2 1⁄2”

2 3⁄4”

SPECIFICATIONS

Construction

Housing is extruded aluminum forming a
2 3⁄4” x 2 1⁄2” rectangular profile. Die-cast end plate
mechanically attaches with no exposed fasteners.

Shielding

Small windows with soft white aluminum bae.

Reflectors

Die-formed, pre-finished white reflector with
hammertone specular aluminum.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Finish

Standard colors include satin anodized aluminum,
and white white (low gloss).

Luminaire Length

8’ and 12’ lengths in a single section for suspension
spacing of 8’ and 12’. For total luminaire length, add

3

⁄4” for each end plate. Using internal joiners, 4’, 8’,

and 12’ sections can be joined to form longer rows.

CATALOG NUMBER

Examples: LL1M3 1 32 12FT R12 120 GEB10 SCT LP835 F1/12 C100 — LL1M3 1 32 16FT R8 277 GEB10 1SE EC SCT LP841 F2/12 C041

__________ __________ __________ _________ __________ __________ __________ __________ __________

Luminaire

LL1M3

______________ ________________ ______________ ______________ ______________ _________________________________

Switching

SCT Single circuit

Notes:

1 Not available in 347V
2 Emergency type is installed in last 4’ of luminaire sections.

3 Not available in 4’ section

# of
Lamps in
Cross
Section

1

Lamp Type

32 32W T8

Luminaire
Row
Length

X FT

(4’ increments)

Lamp Color

L/LP No lamp
L/LPE No lamp. Wired

for energy saving
lamps.

LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

Reference Lamp Chart on
website or consult factory
for other options.

Separate feed required unless ELS or ELS2 is specified

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Mounting Type /

F1/ T-bar ceiling (universal

mounting bracket)

F1A/ T-bar ceiling (UMB with

integrated J-box)

F2/ Hard ceiling (horizontal

J-box)

F3/ Rigid stem

Voltage

120
277
347

Ballast Type

GEB10 <10% THD Electronic
ADEZ Advance Mark 10 dim
ADZT Advance Mark 7 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

Overall Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall suspension is
measured from ceiling to
bottom of luminaire.

Finish

C041 White white (low

gloss)

C100 Satin anodized

finish

C099 Custom finish

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Emergency Type

(Blank) None
EC Emergency circuit

1,3

EL

Emergency battery pack

1,3

EN

Emergency battery pack

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy (not available with F3)
CP Chicago plenum (available with F1A only)
DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per row/zone
OJB Oset junction box
SLP Sloped ceiling (for 10-45°, must be specified with F2, ACG and

OJB options)

XXXX Integrated sensor; choose options and obtain code on page 2

2

w/night light circuit

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Lightline” are registered trademarks of Acuity Brands Lighting.

LL1M3  Lightline Lightvent

Indirect T8

1

Type: ________________________

Lightline Lightvent

Project: ______________________

Indirect T8

Suspended LL1M3

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

1

⁄4” (F3)

10 LBS

20 LBS

30 LBS

PLAN VIEW

3’-11

4’-0 1⁄4”

4’-1

3

⁄4” O.A.

7’-11

8’-1

8’-0

5

1

⁄8” (F3)

1

⁄8”

⁄8” O.A.

3

⁄4”

12’-11” (F3)

12’-0”

1

12’-1

⁄2” O.A.

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

CONFIGURATIONS

Mitered “L”, “X” and “T” connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.

PHOTOMETRICS

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

Actual performance may dier as a result of end-user environment and application.

1-LAMP T8

70.3% eciency
2003 delivered lumens

89.5% up / 10.5% down

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Lightline” are registered trademarks of Acuity Brands Lighting.

LL1M3  Lightline Lightvent

Indirect T8

2