Peerless Lighting LD6 User Manual

Solid/Bae Lens/Lens Lens/Solid

Classic Round

6” Diameter T8

Type: ________________________

Project: ______________________

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Suspended / Wall LD6

SPECIFICATIONS

Construction

One- or two-piece nominal 6” diameter
housing is extruded aluminum. Die-cast aluminum
end plates are mechanically attached with no
exposed fasteners.

Reflectors

Formed steel with white finish.

Shielding

Bae: One piece white painted aluminum bae
with snap-on feature.

Upper Lens: Linear prismatic virgin acrylic with snap
on feature. Lens has interior longitudinal prisms and
smooth exterior.

Lower Lens: Linear prismatic virgin acrylic with snap
on feature. Lens has exterior longitudinal prisms and
smooth interior.

Finish

C041 White white (low gloss) standard; custom
colors available, consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’, 8’, and 12’ lengths in a single section for exact
suspension spacing of 4’, 8’ and 12’. Using internal
joiners 4’, 8’, and 12’ sections can be joined to form
longer rows.

CATALOG NUMBER

Examples: LD6 102203 T8 12FT R12 120 GEB10PS SCT LP830 F1/24 C100 DL

__________ __________ __________ _________ __________ __________ __________ __________

Luminaire

LD6
LD6W

Light Direction/# of Lamps Up/
# of Lamps Down/Shielding

211204

010200

211754

020202

401204

101100

412205

101200

411206

102102

412753

102203

Lamp Type

32 32W T8

(T5, T5HO available with some
shielding options. Consult
factory for more information.)

Luminaire Row
Length, Special

X FT

Maximum
Section Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Voltage

120
277
347

Ballast Type

GEB10PS <10% THD Electronic
ADEZ Advance Mark 10 dim
DMHL3D Lutron Hi-Lume dim
ADZT Advance Mark 7 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

______________ ________________ ________________ ______________ ______________ ______________ _________________________________

Emergency Type

(Blank) None
EC Emergency

circuit

Emergency

EL

battery pack

Emergency

EN

battery pack
w/night light
circuit

Notes:

1 EL and EC are installed in last 4’ of luminaire sections and are not available concurrently.

Separate feed required for each EL, EC or EN unless ELH or ELS is specified

1

Switching

SCT Single circuit
DCT Dual circuit

Lamp Color

L/LP No lamp
L/LPE No lamp. Wired

for energy saving
lamps.

3000K 80+ CRI

LP830
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

Reference Lamp Chart on
website or consult factory
for other options.

Mounting Type /

F1/ T-bar ceiling (universal

mounting bracket)

T-bar ceiling (UMB with

F1A/

integrated J-box)

Hard ceiling (horizontal

F2/

J-box)

Rigid stem

F3/

Overall Suspension

24 24”
48 48”
96 96”
144 144”
XX XX”

Overall suspension is
measured from ceiling to
bottom of luminaire.

Finish

C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish

Options

CP Chicago plenum (available

with F1A only)

Damp location label

DL
ELH Emergency through wiring w/

separate feed

Emergency through wiring w/

ELS

single feed, shared neutral

Fusing (fast blow)

GLR
GMF Fusing (slow blow)
NYC New York City code
RIF Radio interference filter

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Classic Round” are registered trademarks of Acuity Brands Lighting.

LD6  Classic Round

6” Diameter T8

1

Type: ________________________

Classic Round

6” Diameter T8

Suspended / Wall LD6

LAMPING OPTIONS

INDIRECT

LD6 010200

Up Lens with 1 Lamp Up

o

APERTURE

120

6” DIA.

DIRECT

LD6 101100

Down Bae with 1 Lamp Down

” DIA.

o

APERTURE

120

LD6 020202

Up Lens with 2 Lamps Up

o

120

APERTURE

6” DIA.

LD6 101200 Down

Lens with 1 Lamp Down
(wide spread distribution)

6” DIA.

o

120

APERTURE

LD6 102102

Down Bae with
2 Lamps Down

6” DIA.

o

APERTURE

120

LD6 102203

Down Lens with
2 Lamps Down

6” DIA.

o

120

APERTURE

Project: ______________________

I/D

LD6 211204 Up/Down

Lens with 1 Lamp Up,
1 Lamp Down

LD6 211754 Up/Down

Lens Up Bae Down
with 1 Lamp Up, 1 Lamp Down

o

APERTURE

90

6” DIA.

o

APERTURE

90

LD6 401204

Mostly Down
Lens with 1 Lamp Down

o

APERTURE

60

6” DIA.

LD6 411206 Mostly Down

Open Up Lens Down with
1 Lamp Up, 1 Lamp Down

o

60

APERTURE

6” DIA.

o

APERTURE

120

LD6 412205 Mostly Down

Lens with 1 Lamp Up,
2 Lamps Down

o

60

APERTURE

6” DIA.

o

APERTURE

120

LD6 412753

Bae with 1 Lamp Up,
2 Lamps Down

6” DIA.

60

120

o

APERTURE

o

APERTURE

Mostly Down

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Classic Round” are registered trademarks of Acuity Brands Lighting.

LD6  Classic Round

6” Diameter T8

2