Peerless Lighting ICM8 User Manual

Type: ________________________

IceTray Curved I/D

Project: ______________________

Indirect-Direct T8

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Suspended ICM8

LAMPING OPTIONS

ICM8 - 2 ICM8 - 3 ICM8 - 4

10 1⁄2”

3 1⁄8”

10 1⁄2”

3 1⁄8”

10 1⁄2”

SPECIFICATIONS

Construction

Nominal 10” x 3” with extruded aluminum spine
and nominal four 4’ one-piece aluminum
bae assemblies. Steel and die-cast aluminum
sculptured end cap.

Reflectors

White painted center reflector is integrated with
the bae (nominal 90% reflectance). Perforated
side reflector/shield.

Shielding

Straight blade baes with perforated side reflector/
shield. Optional opal acrylic diuser overlay
(recommended with T5HO lamps).

Finish

Satin anodized or white polyester powder paint.
Satin anodized finish consists of satin anodized
housing, clear-coated aluminum baes and end
caps painted C110 to match. Note that clear coated
aluminum baes retain the slight imperfections
and characteristics of the raw aluminum source
material. Custom colors available, consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’, 8’, and 12’ lengths in a single section for exact
suspension spacing of 4’, 8’ and 12’. For total
luminaire length, add 1 3⁄8” for each end cap. Using
internal joiners 4’, 8’, and 12’ sections can be joined
to form longer rows.

CATALOG NUMBER

Examples: ICM8 2 32 20FT R8 120 GEB10 SCT LP835 F1/18 C100 — ICM8 4 32 24FT R8 277 GEB10 SCT LP841 F1/24 C041

3 1⁄8”

__________ __________ __________ __________ __________ _________ __________ __________ __________ __________

Luminaire

ICM8

______________ ________________ ________________ ______________ ______________ ______________ _________________________________

Emergency Type

(Blank) None
EC Emergency

EL4 Emergency

EN4 Emergency

Notes:

1 Percentages with OPD shielding (except 5/95)
2 Not available with OPD
3 Not available with 4-lamps
4 Not available in 347V

# of
Lamps in
Cross
Section

2
3
4

circuit

battery pack

battery pack
w/night light
circuit

Lamp Type

32 32W T8

5

Switching

SCT Single circuit
DCT Dual circuit

Distribution

(Blank) 80% up, 20% down

50/502 50% up, 50% down
30/702 30% up, 70% down
5/952 5% up, 95% down

Lamp Color

L/LP No lamp
L/LPE No lamp. Wired

LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

Reference Lamp Chart on
website or consult factory
for other options.

1

(Standard)

Shielding

(Blank) No opal diuser
OPD Opal diuser

(not available
with 5/95
distribution)

Luminaire
Row
Length

X FT

(4’ increments)

Mounting Type /

F1/ T-bar ceiling (universal

for energy saving
lamps.

5 Emergency type is installed in last 4’ of luminaire sections.

Separate feed required unless ELS or ELS2 is specified

6 Not available with 5/95, 50/50 or 30/70

mounting bracket)

F1A/ T-bar ceiling (UMB with

integrated J-box)

F2/ Hard ceiling (horizontal

J-box)

F3/ Rigid stem

Overall
Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall
suspension is
measured from
ceiling to bottom
of luminaire.

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R123 12’ section(s)

Finish

C041 White white

(low gloss)

C100 Satin anodized

finish

C099 Custom finish

Voltage

120
277
347

Ballast Type

GEB10 <10% THD Electronic
ADEZ4 Advance Mark 10 dim
DMHL3D4 Lutron Hi-Lume dim
OS5C Osram Line or 0-10V

Reference Ballast Wizard on website
or consult factory for other options.

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy (not available with F3

mtg)

CP Chicago plenum (available with F1A only)
DL Damp location label
DU6 Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per row/zone
NYC New York City code
OJB Oset junction box
SLP Sloped ceiling (for 10-45°, must be specified with F2, ACG

and OJB options)

XXXX Integrated sensor; choose options and obtain code on page 2

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “IceTray” are registered trademarks of Acuity Brands Lighting.

ICM8  IceTray Curved I/D

Indirect-Direct T8

1

Type: ________________________

IceTray Curved I/D

Project: ______________________

Indirect-Direct T8

Suspended ICM8

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

18–22 LBS

36–40 LBS

4’-0 1⁄4”

4’-2

1

⁄4” O.A.

8’-0

8’-2

1

⁄8”

1

⁄8” O.A.

1” end cap

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

54–58 LBS

PLAN VIEW

CONFIGURATIONS

PHOTOMETRICS

12’-0”

12’-2” O.A.

Tenon “L”, “X”, “T” and straight connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.

Actual performance may dier as a result of end-user environment and application.

2-LAMP T8

91.9% eciency
5237 delivered lumens

71.1% up / 28.9% down

2-LAMP T8 WITH OPD

89.9% eciency
5127 delivered lumens

79.8% up / 20.2% down

3-LAMP T8

89.6% eciency
7658 delivered lumens

76.8% up / 23.2% down

3-LAMP T8 WITH OPD

88.2% eciency
7538 delivered lumens

84.0% up / 16.0% down

4-LAMP T8

88.1% eciency
10048 delivered lumens

76.1% up / 23.9 % down

4-LAMP T8 WITH OPD

87.4% eciency
9960 delivered lumens

83.1% up / 16.9% down

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “IceTray” are registered trademarks of Acuity Brands Lighting.

ICM8  IceTray Curved I/D

Indirect-Direct T8

2

Type: ________________________

IceTray Curved I/D

Indirect-Direct T8

PHOTOMETRICS

Actual performance may dier as a result of end-user environment and application.

2-LAMP T8 50/50

77.9% eciency
4439 delivered lumens

49.9% up / 50.1% down

2-LAMP T8 30/70

67.8% eciency
3866 delivered lumens

30.9% up / 69.1% down

2-LAMP T8 5/95

62.6% eciency
3569 delivered lumens

Project: ______________________

Suspended ICM8

3-LAMP T8 50/50

69.0% eciency
5902 delivered lumens

50.0% up / 50.0% down

3-LAMP T8 30/70

58.3% eciency
4985 delivered lumens

29.3% up / 70.7% down

3-LAMP T8 5/95

51.6% eciency
4410 delivered lumens

4-LAMP T8 50/50

63.8% eciency
7277 delivered lumens

55.1% up / 44.9% down

4-LAMP T8 30/70

56.8% eciency
6475 delivered lumens

29.1% up / 70.9% down

4-LAMP T8 5/95

45.7% eciency
5210 delivered lumens

5.5% up / 94.5% down

4.2% up / 95.8% down

5.0% up / 95.0% down

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “IceTray” are registered trademarks of Acuity Brands Lighting.

ICM8  IceTray Curved I/D

Indirect-Direct T8

3