Peerless Lighting ICDW User Manual

IceTray Curved Wall
Direct

Direct T8

Type: ________________________

Project: ______________________

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Wall Mount ICDW8

LAMPING OPTIONS

CDW8 - 1

Wall Mount

7 1⁄8”

3

⁄8”

3 13⁄16”

SPECIFICATIONS

Construction

Nominal 4” x 7” with extruded aluminum spine
and nominal four 4’ one-piece aluminum bae
assemblies. Steel and die-cast aluminum sculptured
end cap.

Reflectors

White painted center reflector (nominal 90%
reflectance).

CATALOG NUMBER

Examples: ICDW8 1 32 OPI 40FT R12 277 GEB10 SCT LP835 C100 — ICDW8 1 32 OPI 32FT R8 277 GEB10 1SE EL SCT LP835 CO41

__________ __________ __________ __________ _________ __________ __________ __________ __________

Luminaire

ICDW8

# of
Lamps in
Cross
Section

1

Lamp Type

32 32W T8

Shielding

OPI Intermediate brightness

opal diuser

Standard brightness opal

OPD

diuser

Shielding

Straight blade baes with intermediate brightness
opal acrylic diuser overlay.

Finish

Satin anodized or white polyester powder paint.
Satin anodized finish consists of satin anodized
housing, clear-coated aluminum baes and end
caps painted C110 to match. Note that clear coated
aluminum baes retain the slight imperfections
and characteristics of the raw aluminum source
material. Custom colors available, consult factory.

Luminaire
Row
Length

X FT

(4’ increments)

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Voltage

120
277
347

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’, 8’, and 12’ lengths in a single section for exact
suspension spacing of 4’, 8’ and 12’. For total
luminaire length, add 1 3⁄8” for each end cap. Using
internal joiners 4’, 8’, and 12’ sections can be joined
to form longer rows. Individual 2’ and 3’ units also
available, consult factory

Ballast Type

GEB10 <10% THD Electronic
ADEZ1 Advance Mark 10 dim
DMHL3D1 Lutron Hi-Lume dim
OS5C Osram Line or 0-10V

Reference Ballast Wizard on website
or consult factory for other options.

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

______________ ________________ ________________ ______________ _________________________________

Emergency Type

(Blank) None
EC Emergency circuit
EL1 Emergency battery pack
EN1 Emergency battery pack

w/night light circuit

Notes:

1 Not available in 347V
2 Emergency type is installed in last 4’ of luminaire sections.

Separate feed required unless ELS or ELS2 is specified

2

Switching

SCT Single circuit

Lamp Color

L/LP No lamp
L/LPE No lamp. Wired

for energy saving
lamps.

3000K 80+ CRI

LP830
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

Reference Lamp Chart on
website or consult factory
for other options.

Finish

C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish

Options

DL Damp location label
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
NYC New York City code

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “IceTray” are registered trademarks of Acuity Brands Lighting.

ICDW8  IceTray Curved

Direct T8

1

Type: ________________________

IceTray Curved Wall Direct

Direct T8

Wall Mount ICDW8

MOUNTING DETAIL

Mounting holes to fixture

4 7⁄16”

Wall Bracket

Mounting holes
for 1⁄4” bolt

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Consult factory for stem mounting suspension spacing.

STANDARD SECTIONS

1

⁄8”

8

12–13.5 LBS

8 1⁄16”

24–25.5 LBS

8”

36–37.5 LBS

PLAN VIEW

2’-8”

4’-2 1⁄4” O.A.

2X4 Switch Box
(By others)

1” end cap

6’-8”

1

8’-2

⁄4” O.A.

5’-4” 5’-4”

12’-2” O.A.

Key:

Support location

Standard feed location

EM feed location

•

Project: ______________________

CONFIGURATIONS

Tenon inside, outside “L” and straight connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.

PHOTOMETRICS

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

Actual performance may dier as a result of end-user environment and application.

1-LAMP T8 OPI

42.7% eciency
1216 delivered lumens

50.1% up / 49.9% down

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “IceTray” are registered trademarks of Acuity Brands Lighting.

ICDW8  IceTray Curved

Direct T8

2