Peerless Lighting ICDM User Manual

Type: ________________________

IceTray Curved Direct

Project: ______________________

Direct T5/T5HO

With SBP With OPD

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Surface/Suspended ICDM8

LAMPING OPTIONS

ICDM8 - 1 SBP  ICDM8 S - 1 SBP 

3 13⁄16”

3 13⁄16”

7 1⁄8”

SPECIFICATIONS

7 1⁄8”

Construction

Nominal 7” x 4” with extruded aluminum spine
and nominal four 4’ one-piece aluminum bae
assemblies. Steel and die-cast aluminum sculptured
end cap.

Reflectors

White painted center reflector (nominal 90%
reflectance). Perforated side reflector/shield.

ICDM8 - 2 SBP  ICDM8 S - 2 SBP 

3

⁄8”

3 13⁄16”

7 1⁄8”

7 1⁄8” 7 1⁄8”

Shielding

Straight blade baes with perforated side
reflector/shield or opal acrylic diuser.

Finish

Satin anodized or white polyester powder paint.
Satin anodized finish consists of satin anodized
housing, clear-coated aluminum baes and end
caps painted C110 to match. Note that clear coated
aluminum baes retain the slight imperfections
and characteristics of the raw aluminum source
material. Custom colors available, consult factory.

ICDM8 - 1 OPD  ICDM8 S - 1 OPD 

3

⁄8”

3 13⁄16”

3 13⁄16”

7 1⁄8”

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’, 8’, and 12’ lengths in a single section for exact
suspension spacing of 4’, 8’ and 12’. For total
luminaire length, add 1 3⁄8” for each end cap. Using
internal joiners 4’, 8’, and 12’ sections can be joined
to form longer rows.

CATALOG NUMBER

Examples: ICDM8 2 28T5 SBP 20FT R8 120 GEB10 SCT LP835 F1/24 C100 — ICDM8 1 28T5 OPD 24FT R12 277 GEB10 1SE EN SCT LP841 CO41

3

⁄8”

3 13⁄16”

__________ __________ __________ __________ __________ _________ __________ __________ __________ __________

Luminaire

ICDM8

______________ ________________ ________________ ______________ ______________ ______________ _________________________________

Emergency Type

(Blank) None
EC Emergency

EL2 Emergency

EN2 Emergency

Notes:

1 Not available with 2-lamp cross section
2 Not available in 347V
3 Not available with 28T5 lamps

Ceiling Type

(Blank) Suspended
S Surface

circuit

battery pack

battery pack
w/night light
circuit

mounted

4

Switching

SCT Single circuit
DCT Dual circuit

# of
Lamps in
Cross
Section

1
2

Lamp Type

28T5 28W T5
54T5HO 54W T5HO

Lamp Color

L/LP No lamp
LP830 3000k 80+ CRI
LP835 3500k 80+ CRI
LP841 4100k 80+ CRI

Available with T5 only:
LP830P 3000K 80+

CRI Premier

LP835P 3500K 80+

CRI Premier

LP841P 4100K 80+

CRI Premier

Reference Lamp Chart on
website or consult factory
for other options.

4 Emergency type is installed in last 4’ of luminaire sections.

Separate feed required unless ELS or ELS2 is specified

Shielding

OPD1 Straight blade bae

SBP Straight blade bae

Mounting Type /

F1/ T-bar ceiling (universal

F1A/ T-bar ceiling (UMB with

F2/ Hard ceiling (horizontal

F3/ Rigid stem

with opal diuser

with side perforated
shield

mounting bracket)

integrated J-box)

J-box)

Luminaire
Row
Length

X FT

(4’ increments)

Overall Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall suspension is
measured from ceiling to
bottom of luminaire.

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Finish

C041 White white (low

C100 Satin anodized

C099 Custom finish

Voltage

120
277
347

gloss)

finish

Ballast Type

GEB10 <10% THD Electronic

2,3

ADEZ

Advance Mark 10 dim

DMHL3D2 Lutron Hi-Lume dim

2,3

OSDIM

Osram 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy

(not available with F3)

CP Chicago plenum (available with F1A only)
DL Damp location label
ELH Emergency through wiring w/separate

feed

ELS Emergency through wiring w/single feed,

shared neutral

ELS2 Emergency through wiring w/single feed,

separate neutrals

GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per

row/zone

NYC New York City code
OJB Oset junction box
SLP Sloped ceiling (for 10-45°, must be

specified with F2, ACG and OJB options)

XXXX Integrated sensor; choose options and

obtain code on page 2

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “IceTray” are registered trademarks of Acuity Brands Lighting.

ICDM8  IceTray Curved

Direct T5/T5HO

1

Type: ________________________

IceTray Curved Direct

Project: ______________________

Direct T5/T5HO

Surface/Suspended ICDM8

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

12–13.5 LBS

24–25.5 LBS

4’-0 1⁄4”

4’-2

1

⁄4” O.A.

8’-0

8’-2

1

⁄8”

1

⁄8” O.A.

1” end cap

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

36–37.5 LBS

PLAN VIEW

Surface spacing equals section length.

STANDARD SECTIONS

1

⁄8”

8

12–13.5 LBS

4’-2 1⁄4” O.A.

8 1⁄16”

24–25.5 LBS

8”

36–37.5 LBS

PLAN VIEW

2’-8”

12’-0”

12’-2” O.A.

1” end cap

6’-8”

1

8’-2

⁄4” O.A.

5’-4” 5’-4”

12’-2” O.A.

Key:

Support location

Standard feed location

EM feed location

•

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “IceTray” are registered trademarks of Acuity Brands Lighting.

ICDM8  IceTray Curved

Direct T5/T5HO

2

90 270

Type: ________________________

IceTray Curved Direct

Direct T5/T5HO

Surface/Suspended ICDM8

CONFIGURATIONS

Tenon “L”, “T”, “X” and straight connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.

PHOTOMETRICS

Actual performance may dier as a result of end-user environment and application.

1-LAMP T5HO

90 270

77.9% eciency
3894 delivered lumens

1.7% up / 98.3% down

1-LAMP T5HO OPD

90 270

73.5% eciency
3674 delivered lumens

3.5% up / 95.2% down

Project: ______________________

2-LAMP T5HO

73.0% eciency
7296 delivered lumens

1.3% up / 98.2% down

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.

ICDM8  IceTray Curved Direct

Direct T5/T5HO

3