Peerless Lighting EZM2 User Manual

Type: ________________________

Enzo Indirect

Partial Perforation

Project: ______________________

CWIN Continuous Window

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Indirect T5/T5HO

Suspended EZM2

LAMPING OPTIONS

EZM2 - 1 CWIN EZM2 - 2 CWINEZM2 - 1 EZM2 - 2

2 3⁄16” 2 3⁄16”

6 1⁄2” 6 1⁄2”

6 1⁄2” 6 1⁄2”

2 3⁄16” 2 3⁄16”

SPECIFICATIONS

Construction

6 1⁄2” x 2 3⁄16” one-piece cold-rolled steel housing
with flat end plate.

Reflectors

Die-formed highly reflective white or specular
reflector.

Shielding

Die-punched perforated hole pattern runs
lengthwise across housing body.

Finish

Fine-textured, white polyester powder
paint is standard. Consult factory for special
finish requirements.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’, 8’, and 12’ lengths in a single section for exact
suspension spacing of 4’, 8’, and 12’. For total
luminaire length add 1/16” for each end cap. Using
internal joiners, 4’, 8’, and 12’ sections can be joined
to form longer-length luminaires.

CATALOG NUMBER

Examples: EZM2 1 54T5HO WHR 40FT R12 277 GEB10 2SE EL SCT LP841 F1/24 C518 GLR — EZM2 2 54T5HO SPR CWIN 32FT R8 120 GEB10 DCT LP830 F1/12 C110

__________ __________ __________ __________ __________ _________ __________ __________ __________ __________

Luminaire

EZM2

______________ ________________ ________________ ______________ ______________ ______________ _________________________________

Emergency Type

(Blank) None
EC Emergency

EL1 Emergency

EN1 Emergency

Notes:

1 Not available in 347V
2 Not available with 28T5 lamps

# of
Lamps in
Cross
Section

1
2

circuit

battery pack

battery pack
w/night light
circuit

Lamp Type

28T5 28W T5
54T5HO 54W T5HO

3

Switching

SCT Single circuit
DCT Dual circuit

Reflector

WHR White

SPR Specular

Lamp Color

L/LP No lamp
LP830 3000k 80+ CRI
LP835 3500k 80+ CRI
LP841 4100k 80+ CRI

Available with T5 only:
LP830P 3000K 80+

LP835P 3500K 80+

LP841P 4100K 80+

Reference Lamp Chart on
website or consult factory
for other options.

3 Optional. EC and EL not available concurrently. EL and EC not available with DCT

in 4’ sections. Separate feed required for each EL, EC or EN unless ELH specified

reflector

reflector

CRI Premier

CRI Premier

CRI Premier

Shielding

(Blank) Partial

perforation

CWIN Continuous

perforation

Luminaire
Row
Length

X FT

(4’ increments)

Mounting Type /

F1/ T-bar ceiling (universal

mounting bracket)

F1A/ T-bar ceiling (UMB with

integrated J-box)

F2/ Hard ceiling (horizontal

J-box)

Overall Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall suspension is
measured from ceiling to
bottom of luminaire.

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Voltage

120
277
347

Ballast Type

GEB10 <10% THD Electronic

1,2

ADEZ
DMHL3D1 Lutron Hi-Lume dim
OSDIM

Reference Ballast Wizard on website
or consult factory for other options.

Finish

C110 Painted aluminum

(low gloss)

C518 White (fine-

textured low
gloss)

C099 Custom finish

# of Emergency
Modules

Advance Mark 10 dim

1,2

Osram 0-10V dim

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy
CP Chicago plenum (available with F1A only)
DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed,

shared neutral

ELS2 Emergency through wiring w/single feed,

separate neutrals

GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per row/

zone

NYC New York City code
OJB Oset junction box
SLP Sloped ceiling (for 10-45°, must be

specified with F2, ACG and OJB options)

XXXX Integrated sensor; choose options and

obtain code on page 2

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Enzo” are registered trademarks of Acuity Brands Lighting.

EZM2  Enzo Indirect  Partial Perforation

Indirect T5/T5HO

1

Type: ________________________

Enzo Indirect Partial Perforation

Project: ______________________

Indirect T5/T5HO

Suspended EZM2

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

15 LBS

4’-0

4’-0”

1

⁄8” O.A.

1

⁄16” end plate

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

30 LBS

45 LBS

PLAN VIEW

PHOTOMETRICS

8’-0”

1

⁄8” O.A.

8’-0

12’-0”

1

⁄8” O.A.

12’-0

Actual performance may dier as a result of end-user environment and application.

1-LAMP T5HO

86.6% eciency
4329 delivered lumens

99.0% up / 1.0% down

2-LAMP T5HO

85.4% eciency
8542 delivered lumens

98.8% up / 1.2% down

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Enzo” are registered trademarks of Acuity Brands Lighting.

EZM2  Enzo Indirect Partial Perforation

Indirect T5/T5HO

2