Peerless Lighting ENW1 User Manual

Type: ________________________

Envision Wall

Indirect T8

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

LAMPING OPTIONS

ENW1 - 1 ENW1 - 2

3”

9”

SPECIFICATIONS

Construction

Housing is extruded aluminum forming a 9” x 3”
curved profile. Die-cast end plate attaches with no
exposed fasteners.

Reflectors

Die-formed, pre-finished steel and hammertone
specular aluminum reflector.

Wall Mount ENW1

3”

9”

Finish

Satin anodized or white paint standard. Custom
colors available, consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’, 8’, and 12’ lengths in a single section. For total
luminaire length add 1⁄2” for each end cap. Using
internal joiners, 4’, 8’, and 12’ sections can be joined
to form longer-length luminaires. Individual 2’ and 3’
units also available, consult factory.

Project: ______________________

CATALOG NUMBER

Examples: ENW1 010005 T8 36FT R12 120 GEB10 2SE EL SCT LP835 C041 — ENW1 020006 T8 24FT R8 277 GEB10 DCT LP841 C041

________ ________ ________ ________ ________ ________ ________________________ ______________ ______________

Luminaire

ENW1

________ ________________ ______________ _________________________________

Switching

SCT Single circuit
DCT Dual circuit

# of Lamps
in Cross
Section

010005 1
020006 2

Lamp Type

32 32W T8

Lamp Color

L/LP No lamp
L/LPE No lamp. Wired for energy

saving lamps.

3000K 80+ CRI

LP830
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

Reference Lamp Chart on website or
consult factory for other options.

Nominal
Row
Length

X FT

(4’ increments)

Finish

C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish

Maximum
Section
Length

R2 2’ section(s)
R3 3’ section(s)
R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Voltage

120
277
347

Ballast Type

GEB10 <10% THD Electronic
ADEZ1 Advance Mark 10 dim
DMHL3D1 Lutron Hi-Lume dim
ADZT1 Advance Mark 7 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

Options

CFG Configuration
DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
NYC New York City code

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Emergency Type

(Blank) None
EC Emergency circuit
EL1 Emergency battery

1

Emergency battery

EN

2

pack

pack w/night light
circuit

Notes:

1 Not available in 347V
2 Emergency type is installed in last 4’ of luminaire sections.

Separate feed required unless ELS or ELS2 is specified

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Envision” are registered trademarks of Acuity Brands Lighting.

ENW1  Envision Wall

Indirect T8

1

Type: ________________________

Envision Wall

Indirect T8

MOUNTING DETAIL

Retainer Bracket

Nut #10-24

2 1⁄2”

4”

WEIGHTS & SUPPORT SPACING

STANDARD SECTIONS

2’-8”

24 LBS

1’-4”

1

4’-0

/2” O.A.

Top of fixture
mounting holes

1”

Wall Bracket

2” x 4” switch box
at feed, mounted
horizontally—by others

1

/4” end plate

Project: ______________________

Wall Mount ENW1

1

⁄4”

Caution:

Wall must be adequately reinforced at support
locations for sound structural and aesthetic
installations of the luminaire — by others

Key:

Support location

Standard feed location

EM feed location

•

48 LBS

1’-4”

72 LBS

1’-4”

ELEVATION

CONFIGURATIONS

Cast inside and outside corner connectors available for wall configurations.
Reference Pattern Connector Guide for additional details.

PHOTOMETRICS

6’-8”

1

/2” O.A.

8’-0

5’-4” 5’-4”

1

12’-0

/2” O.A.

Actual performance may dier as a result of end-user environment and application.

1-LAMP T8

62.4% eciency
1811 delivered lumens

100.0% up / 0.0% down

2-LAMP T8

46.9% eciency
2720 delivered lumens

100.0% up / 0.0% down

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Envision” are registered trademarks of Acuity Brands Lighting.

ENW1  Envision Wall

Indirect T8

2