Peerless Lighting ENM2 User Manual

HOL SLT WIN

Envision Holes,
Slots, Windows

Indirect T8

Type: ________________________

Project: ______________________

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Suspended ENM2

LAMPING OPTIONS

ENM2  1 HOL  1 SLT  1 WIN

3”

8”

ENM2  2 HOL  2 SLT  2 WIN ENM2  3 HOL  3 SLT  3 WIN

3”

8”

8”

3”

SPECIFICATIONS

Construction

Housing is extruded aluminum forming a 8” x 3”
curved profile. Die-cast end plate attaches with no
exposed fasteners.

Shielding

Die-punched pattern in aluminum housing.

Reflectors

Die-formed pre-painted white steel, hammertone
specular aluminum and specular aluminum.

Finish

Satin anodized or white paint standard. Custom
colors available, consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’ 1⁄4”, 8’, and 12’ lengths in a single section for
exact suspension spacing of 4’, 8’, and 12’. For total
luminaire length add 1⁄2” for each end cap. Using
internal joiners, 4’, 8’, and 12’ sections can be joined
to form longer-length luminaires.

CATALOG NUMBER

Examples: ENM2 1 32 HOL 40FT R12 120 GEB10 2SE EL SCT LP841 F1/24 C100 — ENM2 3 32 HOL 12FT R4 277 GEB10 DCT LP835 F2/15 C041 ACG

________ ________ ________ ________ ________ ________ ________ ________________________ ______________ ______________

Luminaire

ENM2

# of
Lamps in
Cross
Section

1
2
3

Lamp Type

32 32W T8

Shielding
Options

HOL Holes
SLT Slots
WIN Windows

Nominal
Row
Length

X FT

(4’ increments)

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Voltage

120
277
347

Ballast Type

GEB10 <10% THD Electronic
ADEZ1 Advance Mark 10 dim
DMHL3D1 Lutron Hi-Lume dim
ADZT1 Advance Mark 7 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Emergency Type

(Blank) None
EC Emergency circuit
EL1 Emergency battery

EN1 Emergency battery

2

pack

pack w/night light
circuit

________ ________________ ______________ ______________ ______________ _________________________________

Switching

SCT Single

DCT Dual

Notes:

1 Not available in 347V
2 Emergency type is installed in last 4’ of luminaire sections. Separate feed required unless

ELS or ELS2 is specified. EL and EN not available with DCT option in 4’ individual luminaires.

circuit

circuit

Lamp Color

L/LP No lamp
L/LPE No lamp. Wired

for energy saving
lamps.

LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

Reference Lamp Chart on
website or consult factory for
other options.

Mounting Type /

F1/ T-bar ceiling (universal

mounting bracket)

F1A/ T-bar ceiling (UMB with

integrated J-box)

F2/ Hard ceiling (horizontal

J-box)

Overall
Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall suspension
is measured from
ceiling to bottom
of luminaire.

Finish

C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy
CP Chicago plenum (available with F1A mtg only)
DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per row/zone
NYC New York City code
OJB Oset junction box
SLP Sloped ceiling (for 10-45°, must be specified with F2, ACG and

OJB options)

XXXX Integrated sensor; choose options and obtain code on page 2

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Envision” are registered trademarks of Acuity Brands Lighting.

ENM2  Envision Holes, Slots, Windows

Indirect T8

1

Type: ________________________

Envision Holes, Slots, Windows

Project: ______________________

Indirect T8

Suspended ENM2

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

1

⁄8”

1

⁄4” O.A.

9

⁄16” end plate

24 LBS

43 LBS

4’-0 1⁄4”

4’-1

3

⁄8” O.A.

8’-0

8’-1

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

62 LBS

PLAN VIEW

CONFIGURATIONS

PHOTOMETRICS

12’-0”

1

⁄8” O.A.

12’-1

Mitered corner, “T” and “X” connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.

Actual performance may dier as a result of end-user environment and application.

1-LAMP T8
WITH HOLES

87.2% eciency
2486 delivered lumens

99.0% up / 1.0% down

1-LAMP T8
WITH SLOTS

87.2% eciency
2486 delivered lumens

99.0% up / 1.0% down

2-LAMP T8
WITH HOLES

84.5% eciency
4814 delivered lumens

98.2% up / 1.8% down

2-LAMP T8
WITH SLOTS

84.5% eciency
4814 delivered lumens

98.2% up / 1.8% down

3-LAMP T8
WITH HOLES

81.6% eciency
6977 delivered lumens

98.5% up / 1.5% down

3-LAMP T8
WITH SLOTS

81.6% eciency
6977 delivered lumens

98.5% up / 1.5% down

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Envision” are registered trademarks of Acuity Brands Lighting.

ENM2  Envision Holes, Slots, Windows

Indirect T8

2