Peerless Lighting EGSAM2 User Manual

Lightedge Angular
Shallow Slots

Indirect T8

Type: ________________________

Project: ______________________

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Suspended EGSAM2

LAMPING OPTIONS

EGSAM2 - 2

1 3⁄4”

8”

SPECIFICATIONS

Construction

Housing and end caps are extruded aluminum
forming an 8” x 1 3⁄4” angular profile.

Reflectors

Die-formed, pre-painted white steel, hammertone
specular aluminum and specular aluminum.

Shielding

Opal acrylic overlay above die-punched slot pattern
in aluminum housing.

Finish

Satin anodized standard. Custom colors available,
consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’ and 8’ lengths in a single section for exact
suspension spacing of 4’ and 8.’ For total luminaire
length add 4” for each end cap. Using internal
joiners, 4’ and 8’ sections can be joined to form
longer-length luminaires.

CATALOG NUMBER

Examples: EGSAM2 2 32 40FT R8 120 GEB10 2SE EL SCT LP835 F1/24 C100 — EGSAM2 2 32 12FT R8 277 GEB10 DCT L/LP F2/15 C100 ACG

__________ __________ __________ _________ __________ __________ __________ __________ __________

Luminaire

EGSAM2

# of Lamps in
Cross Section

2

Lamp Type

32 32W T8

Luminaire Row
Length

X FT

(4’ increments)

Maximum
Section Length

R4 4’ section(s)
R8 8’ section(s)

Voltage

120
277
347

Ballast Type

GEB10 <10% THD Electronic
ADEZ1 Advance Mark 10 dim
DMHL3D1 Lutron Hi-Lume dim
ADZT1 Advance Mark 7 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Emergency Type

(Blank) None
EC Emergency circuit
EL1 Emergency battery pack
EN1 Emergency battery pack

2

w/night light circuit

______________ ________________ ______________ ______________ ______________ _________________________________

Switching

SCT Single circuit
DCT Dual circuit

Notes:

1 Not available in 347V
2 Emergency type is installed in last 4’ of luminaire sections.

Separate feed required unless ELS or ELS2 is specified

Lamp Color

L/LP No lamp
L/LPE No lamp. Wired

for energy saving
lamps.

LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

Reference Lamp Chart on
website or consult factory
for other options.

Mounting Type /

F1/ T-bar ceiling (universal

mounting bracket)

F1A/ T-bar ceiling (UMB with

integrated J-box)

F2/ Hard ceiling (horizontal

J-box)

Overall Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall suspension is measured
from ceiling to bottom of
luminaire.

Finish

C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy
CP Chicago plenum (available with F1A only)
DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per row/zone
OJB Oset junction box
SLP Sloped ceiling (for 10-45°, must be specified with F2, ACG

and OJB options)

XXXX Integrated sensor; choose options and obtain code on page 2

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Lightedge” are registered trademarks of Acuity Brands Lighting.

EGSAM2  Lightedge Angular Shallow Slots

Indirect T8

1

Type: ________________________

Lightedge Angular Shallow Slots

Project: ______________________

Indirect T8

Suspended EGSAM2

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

19 LBS

38 LBS

PLAN VIEW

4’-0 1⁄4”

4’-8

1

⁄4” O.A.

8’-0

8’-8

1

⁄8”

1

⁄8” O.A.

4” end plate

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

CONFIGURATIONS

Sweep, mitered corner, “T” and “X” mitered connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.

PHOTOMETRICS

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

Actual performance may dier as a result of end-user environment and application.

2-LAMP T8

75.2% eciency
4288 delivered lumens

97.5% up / 2.5% down

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Lightedge” are registered trademarks of Acuity Brands Lighting.

EGSAM2  Lightedge Angular Shallow Slots

Indirect T8

2