Peerless Lighting EGRM2 User Manual

Lightedge Rectangular
Slots

Indirect T5/T5HO

Type: ________________________

Project: ______________________

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Suspended EGRM2

LAMPING OPTIONS

EGRM2 - 1 EGRM2 - 2 EGRM2 - 3

1 1⁄2” 1 1⁄2” 1 1⁄2”

8 1⁄8” 8 1⁄8” 8 1⁄8”

SPECIFICATIONS

Construction

Housing and end caps are extruded aluminum
forming an 8 1⁄8” x 1 1⁄2” rectangular profile.

Reflectors

Die-formed center reflectors with baked-white
enamel finish (nominal reflectance 90%) and
specular aluminum side reflectors.

Shielding

Opal acrylic overlay above die-punched slot pattern
in aluminum housing.

Finish

Satin anodized standard. Custom colors available,
consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors

included. UL and C-UL listed.

Luminaire Length

4’ and 8’ lengths in a single section for exact
suspension spacing of 4’ and 8.’ For total luminaire
length add 4” for each end cap. Using internal
joiners, 4’ and 8’ sections can be joined to form
longer-length luminaires.

CATALOG NUMBER

Examples: EGRM2 3 54T5HO 12FT R8 277 GEB10 DCT L/LP F2/15 C100 ACG

__________ __________ __________ _________ __________ __________ __________ __________ __________

Luminaire

EGRM2

# of Lamps in
Cross Section

1
2
3

Lamp Type

28T51 28W T5
54T5HO 54W T5HO

Luminaire Row
Length

X FT

(4’ increments)

Maximum
Section Length

R4 4’ section(s)
R8 8’ section(s)

Voltage

120
277

2

347

Ballast Type

GEB10 <10% THD Electronic

1,2

ADEZ

Advance Mark 10 dim

DMHL3D1 Lutron Hi-Lume dim

1,2

OSDIM

Osram 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Emergency Type

(Blank) None
EC Emergency circuit
EL1 Emergency battery pack
EN1 Emergency battery pack

3

w/night light circuit

______________ ________________ ______________ ______________ ______________ _________________________________

Switching

SCT Single circuit
DCT Dual circuit

Notes:

1 Not available in 347V
2 Not available with 28T5 lamps

Lamp Color

L/LP No lamp
LP830 3000k 80+ CRI
LP835 3500k 80+ CRI
LP841 4100k 80+ CRI

Available with T5 only:
LP830P 3000K 80+

CRI Premier

LP835P 3500K 80+

CRI Premier

LP841P 4100K 80+

CRI Premier

Reference Lamp Chart on
website or consult factory
for other options.

3 Emergency type is installed in last 4’ of luminaire sections.

Separate feed required unless ELS or ELS2 is specified

Mounting Type /

F1/ T-bar ceiling (universal

mounting bracket)

F1A/ T-bar ceiling (UMB with

integrated J-box)

F2/ Hard ceiling (horizontal

J-box)

Overall Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall suspension is measured
from ceiling to bottom of
luminaire.

Finish

C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy
CP Chicago plenum (available with F1A only)
DL Damp location label
DU Dust cover (not available with 3-lamp cross section)
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per row/zone
OJB Oset junction box
SLP Sloped ceiling (for 10-45°, must be specified with F2, ACG

and OJB options)

XXXX Integrated sensor; choose options and obtain code on page 2

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Lightedge” are registered trademarks of Acuity Brands Lighting.

EGRM2  Lightedge Rectangular Slots

Indirect T5/T5HO

1

Type: ________________________

Lightedge Rectangular Slots

Project: ______________________

Indirect T5/T5HO

Suspended EGRM2

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

19 LBS

38 LBS

PLAN VIEW

4’-0 1⁄4”

4’-8

1

⁄4” O.A.

8’-0

8’-8

1

⁄8”

1

⁄8” O.A.

4” end plate

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

CONFIGURATIONS

Sweep, mitered corner, “T” and “X” mitered connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.

PHOTOMETRICS

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

Actual performance may dier as a result of end-user environment and application.

1-LAMP T5HO

82.8% eciency
4141 delivered lumens

99.2% up / 0.8% down

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Lightedge” are registered trademarks of Acuity Brands Lighting.

2-LAMP T5HO

81.1% eciency
8108 delivered lumens

99.1% up / 0.9% down

3-LAMP T5HO

78.1% eciency
11718 delivered lumens

99.0% up / 1.0% down

EGRM2  Lightedge Rectangular Slots

Indirect T5/T5HO

2