Peerless Lighting CRW4 User Manual

DAY

10

5

10

DAY

10

10

CRW4QS

®

Wall

Cerra

Specifications

with PERF

SCEP option

Catalog Number

___________ ___________ ___________ ___________ ___________ ___________ ___________

Luminaire # of Lamps in

CRW4QS

CRW4QST

Cross Section

1
2

Lamp Type Reflector Shielding Luminaire Row

28T5 28W T5
54T5HO 54W T5HO
32 32W T8

CONSTRUCTION — Housing is formed from one-piece cold-rolled steel. Flat end plate standard.
Sculptured die-cast aluminum end cap is optional.

SHIELDING — Window opening with straight blade bae and white opal overlay.

REFLECTORS — Die-formed highly reflective white or specular reflector.

FINISH — Fine textured white polyester powder paint.

LUMINAIRE LENGTH — Nominal 4’, 8’, and 12’ sections form row lengths. Actual section
length = 11 5⁄8” per nominal foot specified. For total run length, add 1⁄16” for each flat end plate or
4” for each sculptured end cap. For longer run lengths, sections are attached using internal joiners.

DISTRIBUTION — 6–8% downlight. See non-QuickShip spec sheet for photometrics.

Sample Catalog Number: CRW4QS 1 54T5HO WHR 40FT R12 277 GEB10 SCT LP835 C210 SCEP

WHR White

reflector

SPR Specular

reflector

NOPERF Without

perforated
window

PERF Perforated

window

Length

X FT

(4’ increments)

Maximum
Section Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Voltage Ballast Type # of Emergency

120
277

GEB10 <10% THD Electronic (32 T8, 28T5,

54T5HO)

GEB10/347V 347V Generic non-dim Only available

with 10-day QuickShip

OS5C Osram 0-10V dim or line voltage control

ADEZ Advance Mark 10 dim (54T5HO)
OSDIM Osram 0-10V dim (54T5HO)

ADZT Advance Mark 7 0-10V dim (54T5HO).

Dimensions / Lamping

2 11⁄16”

7 5⁄8”

(1,2) T5, T5HO, or T8

Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

(32 T8)

Only available with 10-day QuickShip

___________ ___________ ___________ ___________ ___________

Emergency Type1Switching Lamp Color Finish Options

(Blank) None
EC2 Emergency

circuit

I/D

EL Emergency

battery pack

EN2 Emergency

battery pack
w/night light
circuit

Notes:  1 Emergency type is installed in last 4’ of luminaire sections. Separate feed required unless ELS or ELS2 is specified 2 Not available with dimming 

SCT Single circuit
DCT2 Dual circuit

L/LP* No lamp
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

*Wired for full wattage
lamps only, do not install
low wattage lamps

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Specifications subject to change without notice. 1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Cerra” are registered trademarks of Acuity Brands Lighting. Products in this document may be covered by one or more U.S. Patents and Patents Pending.

C210 White white

(fine-textured
low gloss)

DU Dust cover
ELH Emergency through wiring w/separate feed
ELS2 Emergency through wiring w/single feed, shared neutral
ELS22 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
SCEP Sculptured end cap