Peerless Lighting CRW3 User Manual

Type: ________________________

Cerra Wall

Lightvent

Indirect-Direct T5/T5HO

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

LAMPING OPTIONS

CRW3 - 1 CRW3 - 2

2 11⁄16”

7 5⁄8”

SPECIFICATIONS

Construction

Housing is formed from one-piece cold-rolled
steel. Flat end plate standard. Sculptured die-cast
aluminum end cap is optional.

Reflectors

Die-formed highly reflective white or specular
reflector.

Shielding

Die-punched perforated window on lower housing
with acrylic opal diuser overlay.

Wall Mount CRW3

Optional sculptured end cap

2 11⁄16”

7 5⁄8”

Finish

Fine-textured, white or aluminum polyester powder
paint. Custom colors available, consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

Nominal 4’, 8’, and 12’ sections form row lengths.
Consult factory for 2’ and 3’ sections. For total run
length, add 1⁄16” for each flat end plate or 4” for each
sculptured end cap. For longer run lengths, sections
are attached using internal joiners.

Project: ______________________

CATALOG NUMBER

Examples: CRW3 1 54T5HO WHR 40FT R12 277 GEB10 SCT LP835 C210 SCEP — CRW3 2 54T5HO SPR 32FT R8 277 GEB10 1SE EL DCT LP835 C110

__________ __________ __________ __________ _________ __________ __________ __________ __________

Luminaire

CRW3

______________ __________ ________________ ______________ _________________________________

Emergency Type

(Blank) None
EC Emergency circuit
EL Emergency battery pack
EN Emergency battery pack

# of
Lamps in
Cross
Section

1
2

3

w/night light circuit

Lamp Type

28T5 28W T5
54T5HO 54W T5HO

Switching

SCT Single circuit
DCT Dual circuit

Reflector

WHR White

Reflector
(Standard)

SPR Specular

Reflector

Luminaire
Row
Length

X FT

(4’ increments)

Lamp Color

L/LP No lamp
LP830 3000k 80+ CRI
LP835 3500k 80+ CRI
LP841 4100k 80+ CRI

Available with T5 only:
LP830P 3000K 80+ CRI Premier
LP835P 3500K 80+ CRI Premier
LP841P 4100K 80+ CRI Premier

Reference Lamp Chart on website or
consult factory for other options.

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Voltage

120
277
347

Finish

C110 Painted aluminum (low gloss)
C210 White white (fine-textured low gloss)
C099 Custom finish

Ballast Type

GEB10 <10% THD Electronic

1,2

ADEZ

Advance Mark 10 dim

DMHL3D1 Lutron Hi-Lume dim

1,2

OSDIM

Osram 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

Options

DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
SCEP Sculptured end cap

# of Emergency Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Notes:

1 Not available in 347V
2 Not available with 28T5 lamps

3 EL and EC are installed in last 4’ of luminaire sections.

Separate feed required unless ELS or ELS2 is specified

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Cerra” are registered trademarks of Acuity Brands Lighting.

CRW3  Cerra Wall  Lightvent

Indirect-Direct T5/T5HO

1

Type: ________________________

Cerra Wall Lightvent

Indirect-Direct T5/T5HO

Wall Mount CRW3

MOUNTING DETAIL

2 13⁄16”

Mtg holes for 1⁄4” bolt

WEIGHTS & SUPPORT SPACING

STANDARD SECTIONS

13

⁄16”

2

12 LBS

typical

1’-10

1’-4”

5

⁄8” O. A.

C

L

.75”

1

⁄16” standard flat end plates

4” optional sculptured end plates

Wall Bracket

2 x 4 switch box

(by others)

1 11⁄16” Mtg holes to
bottom of housing

#10–24 screws

5

7

⁄8”

Key:

Support location

Standard feed location

EM feed location

•

Project: ______________________

11

⁄16”

2

14 LBS

16 LBS

27 LBS

38 LBS

ELEVATION

CONFIGURATIONS

PHOTOMETRICS

2’-4”

2’-10 5⁄8” O.A.

2’-8”

5⁄8”

3’-10 5⁄8” O.A.

6’-8”

1

⁄8” O.A.

7’-9

5’-4” 5’-4”

11’-7 5⁄8” O.A.

Cast aluminum tenon, inside and outside “L” connectors available for wall configurations.
Reference Pattern Connector Guide for additional details.

Actual performance may dier as a result of end-user environment and application.

1-LAMP T5HO
WITH WHITE REFLECTOR

75.8% eciency
3791 delivered lumens

2-LAMP T5HO
WITH WHITE REFLECTOR

70.7% eciency
7066 delivered lumens

96.3% up / 3.7% down

96.4% up / 3.6% down

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Cerra” are registered trademarks of Acuity Brands Lighting.

CRW3  Cerra Wall Lightvent

Indirect-Direct T5/T5HO

2