Peerless Lighting CLM9 User Manual

Type: ________________________

Contrail Linear

Indirect-Direct T5/T5HO

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Suspended CLM9

Project: ______________________

LAMPING OPTIONS DESIGN GUIDELINES

CLM9 - 2

6”

Because the shielding (diuser) is fully luminous,
color variations in the lamp may create subtle
fluctuations in the color of the shield.

3”

If dual switching is required for energy savings,
dimming or the alternating lamp circuit switching

option (ALC) is recommended in place of the dual
circuit switching option (DCT). DCT will switch
each side of a luminaire row separately which will
aect the uniform luminous aesthetic of the lens.
ALC will switch every other 4’ section of a luminaire
row separately.

SPECIFICATIONS

Construction

Die-formed pre-painted steel housing. Extruded
aluminum fillers. Die-cast aluminum end caps.
Highly specular aluminum end plates.

Shielding

GrateOptic curved, crenulated diuser is extruded
opal acrylic.

Reflectors

Die-formed, highly specular aluminum reflector has
a minimum 98% reflectance.

Finish

Fine-textured, white polyester powder paint is
standard on the fillers and end caps.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’, 8’, and 12’ individual luminaire sections for
nominal suspension spacing of 4’, 8’ and 12’. Add
3 5⁄8” for each end cap to determine total luminaire
length. Using internal joiners, 4’, 8’ and 12’ sections
can be joined to form longer length luminaires.

CATALOG NUMBER

Examples: CLM9 2 28T5 COA 40FT R8 277 GEB10 SCT LP835 F1/18 — CLM9 2 54T5HO COA 32FT R8 277 GEB10 1SE EL SCT LP835 F1/21

__________ __________ __________ __________ _________ __________ __________ __________ __________ __________

Luminaire

CLM9

______________ ________________ ______________ ______________ _________________________________

Switching

SCT Single circuit
ALC Alternate lamping

Notes:

1 Not available in 347V
2 Not available with 28T5 lamps
3 Emergency type is installed in last 4’ of luminaire sections.

Separate feed required unless ELS or ELS2 is specified

4 Option EL or EN (Battery Pack) is :

a. not permitted with dimming in the same row

# of
Lamps in
Cross
Section

2

5

module circuit

Lamp Type

28T5 28W T5
54T5HO 54W T5HO

Shielding

COA Crenulated

Lamp Color

L/LP No lamp
LP830 3000k 80+ CRI
LP835 3500k 80+ CRI
LP841 4100k 80+ CRI

Available with T5 only:
LP830P 3000K 80+ CRI Premier
LP835P 3500K 80+ CRI Premier
LP841P 4100K 80+ CRI Premier

Reference Lamp Chart on website or
consult factory for other options.

Luminaire
Row

opal
acrylic

Length

X FT

(4’ increments)

Mounting Type /

F1/ T-bar ceiling (universal

mounting bracket)

F1A/ T-bar ceiling (UMB with

integrated J-box)

F2/ Hard ceiling (horizontal J-box)

b. must be in the same section as the lamp being operated
c. not permitted in a 4’ section
d. limited to one battery pack per section

5 SCT with or without dimming, or ALC is recommended

over DCT. DCT and ALC are not available with dimming

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Overall Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall suspension is
measured from ceiling to
bottom of luminaire.

Voltage

120
277

2

347

Ballast Type

GEB10 <10% THD Electronic

1,2

ADEZ

Advance Mark 10 dim

DMHL3D1 Lutron Hi-Lume dim

1,2

OSDIM

Osram 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy
DL Damp location label
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per row/zone
OJB Oset junction box
SLP Sloped ceiling (for 10-45°, must be specified with F2, ACG and

OJB options)

XXXX Integrated sensor; choose options and obtain code on page 2

Emergency Type

(Blank) None
EC Emergency circuit

1,4

EL

1,4

EN

3

Emergency battery

pack

Emergency battery

pack w/night light
circuit

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Contrail” are registered trademarks of Acuity Brands Lighting.

CLM9  Contrail Linear

Indirect-Direct T5/T5HO

1

Type: ________________________

Contrail Linear

Project: ______________________

Indirect-Direct T5/T5HO

Suspended CLM9

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

5

3

⁄8” end cap

12’-0”

1

12’-7

⁄4” O.A.

12 LBS

26 LBS

37 LBS

PLAN VIEW

4’-7

4’-0”

1

⁄4” O.A.

8’-7

8’-0”

1

⁄4” O.A.

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

CONFIGURATIONS

Mitered tenon corner and tenon connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.

PHOTOMETRICS

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

Actual performance may dier as a result of end-user environment and application.

2-LAMP T5

81.8% eciency
4746 delivered lumens

90.1% up / 9.9% down

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Contrail” are registered trademarks of Acuity Brands Lighting.

2-LAMP T5HO

81.8% eciency
8182 delivered lumens

90.1% up / 9.9% down

CLM9  Contrail Linear

Indirect-Direct T5/T5HO

2