Peerless Lighting BRW9 User Manual

Type: ________________________

Bruno Wall

Softshine

Project: ______________________

I/D or Direct T8

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

lamping options

BRW9 - 1 - SSH

1 3⁄4”

8 1⁄4”

spECiFiCations

Construction

Nominal 8 1⁄4” x 1 3⁄4” rectangular housing is formed
from cold-rolled steel. Die-cast end caps are
mechanically attached with no exposed fasteners.

Reflectors

Die-formed white painted reflector.

Shielding

FLush Softshine® high performance lens.

Wall Mount BRW9

Finish

Fine-textured, white polyester powder paint
standard. Consult factory for special finish
requirements.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’ 1⁄16”, 8’ and 12’ lengths in a single section. For
total luminaire length, add 5⁄8” for each flat end cap
and 4” for each sculptured end cap. Using internal
joiners, 4’, 8’ and 12’ sections can be joined to form
longer rows.

Catalog nUmBER

Examples: BRW9 2 32 WHR SSH 40FT R8 120 GEB10 DCT LP835 C210 SCEP — BRW9 1 32 WHR SSH 32FT R8 277 GEB10 1SE EL DCT LP835 C210

__________ __________ __________ __________ __________ _________ __________ __________ __________ __________

Luminaire

BRW9

______________ ________________ ________________ ______________ _________________________________

Emergency Type

(Blank) None
EC Emergency circuit

1

EL
EN

# of
Lamps in
Cross
Section

1

2

Emergency battery pack

1

Emergency battery pack

w/night light circuit

Lamp Type

32 32W T8

Switching

SCT Single circuit
DCT Dual circuit

Reflector

WHR White

reflector

Shielding

SSH Softshine®

high
performance
lens

Luminaire
Row
Length

X FT

(4’ increments)

Lamp Color

L/LP No lamp
L/LPE No lamp. Wired for energy

saving lamps.

LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

Reference Lamp Chart on website or
consult factory for other options.

Maximum
Section Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Finish

C110 Painted aluminum

(low gloss)

C210 White white

(fine-textured
low gloss)

C099 Custom finish

Voltage

120
277
347

Ballast Type

GEB10 <10% THD Electronic

1

Advance Mark 10 dim

ADEZ

1

Lutron Hi-Lume dim

DMHL3D

1

Advance Mark 7 0-10V dim

ADZT

Reference Ballast Wizard on website
or consult factory for other options.

Options

DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
GLR Fusing (fast blow)
GMF Fusing (slow blow)
NYC New York City code
SCEP Sculptured end cap

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Notes:

1 Not available in 347V
2 Emergency type is installed in last 4’ of

luminaire sections. Separate feed required unless ELS or ELS2
is specified

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting.

BRW9Bruno Wall Softshine

I/D or Direct T8

1

2 x 4 switch box

Type: ________________________

Bruno Wall Softshine

I/D or Direct T8

Wall Mount BRW9

MOUNTING DETAIL

feed cover

13

⁄16"

⁄16”

2

3

⁄4"

4’-1 5⁄16” O.A.

to bottom of housing

10"

2’-8”

mounting holes for

1

⁄4"

bolt

mounting

bracket

11

⁄16"

WEIGHTS & SUPPORT SPACING

STANDARD SECTIONS

13

2

typical

16 LBS

1

⁄2"

1

3

⁄4"

1

(2) diameter mounting bolts
— by others

5

⁄8” standard flat end caps

4” optional sculptured end caps

— by others

⁄4"

feed cover

(2) #10-24 mounting screws

mounting bracket

Key:

Support location
Standard feed location
EM feed location

•

Project: ______________________

34 LBS

55 LBS

ELEVATION

CONFIGURATIONS

PHOTOMETRICS

3’-4” 3’-4”

8’-1 1⁄4” O.A.

4’-0” 4’-0”

Tenon inside, outside and straight connectors available for wall configurations.
Reference Pattern Connector Guide for additional details.

Actual performance may dier as a result of end-user environment and application.

1-LAMP T8 WITH SSH

61.7% eciency
1758 delivered lumens

79.8% up / 20.2% down

2’-8”

12’-1 1⁄4” O.A.

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting.

BRW9Bruno Wall Softshine

I/D or Direct T8

2