Peerless Lighting BRM3 User Manual

Type: ________________________

Bruno Holes

Indirect T8

SCEP Option

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Suspended BRM3

Project: ______________________

LAMPING OPTIONS

BRM3 - 1 BRM3 - 2 BRM3 - 3

8 1⁄4”

1 3⁄4”

1

⁄2”

8 1⁄4”

1 3⁄4”

1 3⁄4”

1

⁄2”

1

⁄2”

8 1⁄4”

SPECIFICATIONS

Construction

Nominal 8 1⁄4” x 1 3⁄4” rectangular housing is formed
from cold-rolled steel. Die-cast end caps are
mechanically attached with no exposed fasteners.

Reflectors

Die-formed specular reflector with 95% reflectance.

Shielding

Aluminum, die-formed drop pan with five 2 3⁄4”
cylinder openings of down light feature. Also

available with acrylic opal overlay on top of down
light openings.

Finish

Fine textured white polyester powder paint is
standard. Drop pan always C110 painted
Aluminum Finish. Consult factory for special
finish requirements.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,

consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’ 3⁄8”, 8’ and 12’ lengths in a single section for
nominal support spacing at 4’, 8’ and 12’. For total
luminaire length, add 5⁄8” for each flat end cap
and 4” for each sculptured end cap. Using internal
joiners, 4’, 8’ and 12’ sections can be joined to form
longer rows.

CATALOG NUMBER

Examples: BRM3 2 32 SPR 40FT R8 277 GEB10 DCT LP835 F1/18 C210 SCEP — BRM3 3 32 SPR OPD 32FT R8 277 GEB10 1SE EL DCT LP835 F1/21 C110

__________ __________ __________ __________ __________ _________ __________ __________ __________ __________

Luminaire

BRM3

______________ __________ ________________ ______________ ______________ ______________ _________________________________

Emergency Type

(Blank) None
EC Emergency

EL1 Emergency

EN1 Emergency

Notes:

1 Not available in 347V
2 Emergency type is installed in last 4’ of luminaire sections.

Separate feed required unless ELS or ELS2 is specified

# of
Lamps in
Cross
Section

1
2
3

circuit

battery pack

battery pack
w/night light
circuit

Lamp Type

32 32W T8

2

Switching

SCT Single

DCT Dual

Lamp Color

L/LP No lamp

circuit

L/LPE No lamp. Wired

circuit

LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

Reference Lamp Chart on
website or consult factory
for other options.

Reflector

SPR Specular

reflector

for energy saving
lamps.

Shielding

(Blank) None
OPD Bae w/std

brightness
opal diuser
overlay

Luminaire
Row
Length

X FT

(4’ increments)

Mounting Type /

F1/ T-bar ceiling (universal

mounting bracket)

F1A/ T-bar ceiling (UMB with

integrated J-box)

F2/ Hard ceiling (horizontal

J-box)

F3/ Rigid stem

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Overall Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall suspension is
measured from ceiling to
bottom of luminaire.

Voltage

120
277
347

Ballast Type

GEB10 <10% THD Electronic
ADEZ1 Advance Mark 10 dim
DMHL3D1 Lutron Hi-Lume dim
OSDIM1 Osram 0-10V dim

Reference Ballast Wizard on website
or consult factory for other options.

Finish

C110 Painted aluminum

(low gloss)

C210 White white

(fine-textured
low gloss)

C099 Custom finish

# of Emergency Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy (not available

with F3)

CP Chicago plenum (available with F1A only)
DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate

neutrals

GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per row/zone
NYC New York City code
OJB Oset junction box
SCEP Sculptured end cap
SLP Sloped ceiling (for 10-45°, must be specified with

F2, ACG and OJB options)

XXXX Integrated sensor; choose options and obtain code

on page 2

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting.

BRM3  Bruno Holes

Indirect T8

1

Type: ________________________

Bruno Holes

Project: ______________________

Indirect T8

Suspended BRM3

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

22 LBS

4’-0 3⁄8”

4’-1 5⁄8” O.A.

5

⁄8” standard flat end plates

4” optional sculptured end plates

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

x Please consult factory for sensor placement

38 LBS

54 LBS

PLAN VIEW

CONFIGURATIONS

PHOTOMETRICS

8’-0”

8’-1 1⁄4” O.A.

12’-0”

12’-1 1⁄4” O.A.

Tenon “L”, “T”, “X” and straight connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.

Actual performance may dier as a result of end-user environment and application.

1-LAMP T8

83.7% eciency
2385 delivered lumens

90.8% up / 9.2% down

2-LAMP T8

82.2% eciency
4686 delivered lumens

90.6% up / 9.4% down

3-LAMP T8

78.7% eciency
4487 delivered lumens

90.3% up / 9.7% down

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Peerless Bruno” are registered trademarks of Acuity Brands Lighting.

BRM3  Bruno Holes

Indirect T8

2