Peerless Lighting BRM1 User Manual

DAY

10

5

10

DAY

10

10

BRM1QS

Bruno

SCEP option

Catalog Number

___________ ___________ ___________ ___________ ___________ ___________ ___________ ___________ ___________

Luminaire # of Lamps in

BRM1QS

BRM1QST

Cross Section

1
2
3

Specifications

CONSTRUCTION — Nominal 8 1⁄4” x 1 3⁄4” rectangular housing is formed from cold-rolled steel.
Die-cast end caps are mechanically attached with no exposed fasteners.

REFLECTORS — Die-formed specular reflector with 95% reflectance.

FINISH — Fine textured white polyester powder paint.

LUMINAIRE LENGTH — 4’ 3⁄8”, 8’ and 12’ lengths in a single section for nominal support spacing at
4’, 8’ and 12’. For total luminaire length, add 5⁄8” for each flat end cap and 4” for each sculptured end
cap. Using internal joiners, 4’, 8’ and 12’ sections can be joined to form longer rows.

DISTRIBUTION — 0% downlight. See non-QuickShip spec sheet for photometrics.

Sample Catalog Number: BRM1QS 2 28T5 SPR 24FT R8 120 GEB10 SCT LP835 F1/21 C210

Lamp Type Reflector Luminaire Row

28T5 28W T5
54T5HO 54W T5HO
32 32W T8

SPR Specular

reflector

Length

X FT

(4’ increments)

Maximum
Section Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Dimensions / Lamping

1 3⁄4”

8 1⁄4”

(1,2,3) T5, T5HO, or T8

Voltage Ballast Type # of Emergency

120
277

GEB10 <10% THD Electronic (all lamp types)

GEB10/347V 347V Generic non-dim. Only available with

10-day QuickShip

OS5C Osram 0-10V dim or line voltage control (32 T8)
ADEZ Advance Mark 10 dim (54T5HO)
OSDIM Osram 0-10V dim (54T5HO)

ADZT Advance Mark 7 0-10V dim (54T5HO). Only

available with 10-day QuickShip

Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

___________ ___________ ___________ ___________ ___________ ___________ ___________

Emergency Type1Switching Lamp Color Mounting Type     / Overall Suspension3Finish Options

INDIRECT

(Blank) None
EC2 Emergency

circuit

EL Emergency

battery pack

EN2 Emergency

battery pack
w/night light
circuit

Notes:  1 Emergency type is installed in last 4’ of luminaire sections. Separate feed required unless ELS or ELS2 is specified 

2 Not available with dimming 3 Maximum of 240” 4 Not available with 3 lamp 54T5HO

SCT Single circuit
DCT2 Dual circuit

L/LP* No lamp
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

*Wired for full wattage
lamps only, do not install
low wattage lamps

F1/ T-bar ceiling (universal

mounting bracket)

F1A/ T-bar ceiling (UMB with

integrated J-box)

F2/ Hard ceiling (horizontal

J-box)

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall suspension is
measured from ceiling to
bottom of luminaire

C210 White white

(fine-textured
low gloss)

ACG Adjustable cable grippers
CP Chicago plenum (available with F1A only)
DU4 Dust cover
ELH Emergency through wiring w/separate feed
ELS2 Emergency through wiring w/single feed, shared neutral
ELS22 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
OJB Oset junction box
SCEP Sculptured end cap

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Specifications subject to change without notice. 1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Bruno” are registered trademarks of Acuity Brands Lighting. Products in this document may be covered by one or more U.S. Patents and Patents Pending.