Peerless Lighting 10CRM7 - QS User Manual

DAY

10

5

10

DAY

10

10

10CRM7QS

®

10

Cerra

Specifications

CONSTRUCTION — Nominal 10” x 3” crescent housing is formed from one-piece cold-rolled steel.
Flat end plate standard. Sculptured die-cast aluminum end cap is optional.

SHIELDING — Die-punched perforations on lower housing with acrylic opal diuser overlay.

REFLECTORS — Die-formed highly reflective white or specular reflector.

FINISH — Fine textured white polyester powder paint.

LUMINAIRE LENGTH — 4’, 8’, and 12’ lengths in a single section for exact suspension spacing of
4’, 8’, and 12’. For total luminaire length, add 1⁄16” for each flat end plate or 4” for each sculptured end
cap. Using internal joiners, 4’, 8’, and 12’ sections can be joined to form longer length luminaires.

DISTRIBUTION — 4–6% downlight. See non-QuickShip spec sheet for photometrics.

SCEP option

Catalog Number

___________ ___________ ___________ ___________ ___________ ___________ ___________ ___________

Luminaire # of Lamps in

10CRM7QS

10CRM7QST

Cross Section

2
3
4

Lamp Type Reflector Luminaire Row

32 32W T8 WHR White

Sample Catalog Number: 10CRM7QS 2 32 WHR 40FT R12 277 GEB10 DCT LP735 F1/18 C210 SCEP

reflector

SPR Specular

reflector

Length

X FT

(4’ increments)

Maximum
Section Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Voltage Ballast Type # of Emergency

120
277

GEB10 <10% THD Electronic

GEB10/347V 347V Generic non-dim.

Only available with 10-day QuickShip

OS5C Osram 0-10V dim or line voltage control

ADZT Advance Mark 7 0-10V dim (54T5HO). Only

available with 10-day QuickShip

Dimensions / Lamping

10”

(2,3,4) T8

Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

2 5⁄8”

___________ ___________ ___________ ___________ ___________ ___________ ___________

Emergency Type1Switching Lamp Color Mounting Type     / Overall Suspension3Finish Options

PARTIAL PERFORATION

(Blank) None
EC2 Emergency

circuit

EL Emergency

battery pack

EN2 Emergency

battery pack
w/night light
circuit

Notes:  1 Emergency type is installed in last 4’ of luminaire sections. Separate feed required unless ELS or ELS2 is specified 

2 Not available with dimming 3 Maximum of 240”

SCT Single circuit
DCT2 Dual circuit

L/LP* No lamp
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

*Wired for full wattage
lamps only, do not install
low wattage lamps

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Specifications subject to change without notice. 1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2013 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Cerra” are registered trademarks of Acuity Brands Lighting. Products in this document may be covered by one or more U.S. Patents and Patents Pending.

F1/ T-bar ceiling (universal

mounting bracket)

F1A/ T-bar ceiling (UMB with

integrated J-box)

F2/ Hard ceiling (horizontal

J-box)

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall suspension is
measured from ceiling to
bottom of luminaire

C210 White white

(fine-textured
low gloss)

ACG Adjustable cable grippers
CP Chicago plenum (available with F1A only)
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS2 Emergency through wiring w/single feed, shared neutral
ELS22 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
OJB Oset junction box
SCEP Sculptured end cap