Peerless Lighting 10CRM6 - T8 User Manual

Type: ________________________

Cerra 10

Full Perforation

Project: ______________________

SCEP Option

SPECIFICATIONS

__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________

Indirect T8

Suspended 10CRM6

LAMPING OPTIONS

10CRM6 - 2

2 5⁄8”

10”

SPECIFICATIONS

Construction

Nominal 10” x 3” crescent housing is formed from
one-piece cold-rolled steel. Flat end plate standard.
Sculptured die-cast aluminum end cap is optional.

Reflectors

Die-formed highly reflective white or specular
reflector.

Shielding

Die-punched perforations on lower housing with
acrylic opal diuser overlay.

Finish

Fine-textured, white or aluminum polyester
powder paint. Custom colors available,
consult factory.

Electrical

Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,

consult factory. Plug-in electrical connectors
included. UL and C-UL listed.

Luminaire Length

4’, 8’, and 12’ lengths in a single section for exact
suspension spacing of 4’, 8’, and 12’. For total
luminaire length, add 1⁄16” for each flat end plate
or 4” for each sculptured end cap. Using internal
joiners, 4’, 8’, and 12’ sections can be joined to form
longer length luminaires.

CATALOG NUMBER

Examples: 10CRM6 2 32 WHR 40FT R12 277 GEB10 DCT LP835 F1/18 C210 SCEP — 10CRM6 2 32 SPR 32FT R8 277 GEB10 1SE EL DCT LP835 F1/21 C110

__________ __________ __________ __________ _________ __________ __________ __________ __________ __________

Luminaire

10CRM6

______________ ________________ ______________ ______________ ______________ _________________________________

Switching

SCT Single circuit
DCT Dual circuit

# of
Lamps in
Cross
Section

2

Lamp Color

L/LP No lamp
L/LPE No lamp. Wired

LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI

Reference Lamp Chart on
website or consult factory
for other options.

Lamp Type

32 32W T8

for energy saving
lamps.

Reflector

WHR White

Reflector
(Standard)

SPR Specular

reflector

Luminaire
Row
Length

X FT

(4’ increments)

Mounting Type /

F1/ T-bar ceiling (universal

mounting bracket)

F1A/ T-bar ceiling (UMB with

integrated J-box)

F2/ Hard ceiling (horizontal

J-box)

F3/ Rigid stem

Maximum
Section
Length

R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)

Overall Suspension

12 12”
15 15”
18 18”
21 21”
24 24”
XX XX”

Overall suspension is measured
from ceiling to bottom of
luminaire.

Voltage

120
277
347

Ballast Type

GEB10 <10% THD Electronic
ADEZ1 Advance Mark 10 dim
DMHL3D1 Lutron Hi-Lume dim
ADZT1 Advance Mark 7 0-10V

Reference Ballast Wizard on website
or consult factory for other options.

Finish

C110 Painted aluminum

C210 White white

C099 Custom finish

dim

(low gloss)

(fine-textured
low gloss)

# of Emergency
Modules

(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections

Emergency Type

(Blank) None
EC Emergency circuit
EL1 Emergency battery pack
EN1 Emergency battery pack

Options

ACG Adjustable cable grippers
BLK Black cord, cord manager and canopy (not available with F3)
CP Chicago plenum (available with F1A only)
DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
MCS Matching feed canopy at support
NEPP5D nLight enabled control module per row/zone
NYC New York City code
OJB Oset junction box
SCEP Sculptured end cap
SLP Sloped ceiling (for 10-45°, must be specified with F2, ACG and

OJB options)

XXXX Integrated sensor; choose options and obtain code on page 2

2

w/night light circuit

Notes:

1 Not available in 347V
2 EL and EC are installed in last 4’ of luminaire sections and are not available concurrently

with each other. Separate feed required for each EL or EC unless ELH is specified

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Cerra” are registered trademarks of Acuity Brands Lighting.

10CRM6  Cerra 10  Full Perforation

Indirect T8

1

Type: ________________________

Cerra 10 Full Perforation

Project: ______________________

Indirect T8

Suspended 10CRM6

INTEGRATED NLIGHT MICRO SENSOR

Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number.

EXAMPLE: PDT1

Sensor Type (choose one)

ADC

nLight model
nES ADCX

PDT

nLight model
nES PDT7 ADCX

For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide
*nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on
wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact [e-mail].

Daylight Dimming

Specify 0-10V dimming ballast
No occupancy sensing

Daylight Dimming and/or Occupancy Detection

Specify 0-10v dimming ballast for daylight dimming
Specify fixed-output ballast for occupancy detection only
(daylight dimming disabled)

1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack

10’ Cat-5e cable and splitter provided

2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack

No Cat-5e cable provided

3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel

10’ Cat-5e cable and splitter provided
Order required remote nLight Power Pack or nPanel
separately through nLight (Acuity Brands Controls)

WEIGHTS & SUPPORT SPACING

Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations.

STANDARD SECTIONS

28 LBS

48 LBS

4’-0 3⁄8”

4’-0

1

⁄2” O.A.

8’-0

8’-0

1

⁄16” standard flat end plates

4” optional sculptured end plates

1

⁄8”

1

⁄4” O.A.

Network Type & Sensor Power Source (choose one)

Key:

Support or feed location

•

68 LBS

PLAN VIEW

CONFIGURATIONS

Cast corner and tenon connectors available for suspended configurations.
Reference Pattern Connector Guide for additional details.

PHOTOMETRICS

12’-0”

1

⁄8” O.A.

12’-0

Actual performance may dier as a result of end-user environment and application.

2-LAMP T8
WHITE REFLECTOR

76.1% eciency
4339 delivered lumens

92.4% up / 7.6% down

2246 5th Street, Berkeley, CA 94710 • Tel: [phone] • Fax: [phone] • Email: [e-mail] • PeerlessLighting.com

Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx

© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Cerra” are registered trademarks of Acuity Brands Lighting.

10CRM6  Cerra 10 Full Perforation

Indirect T8

2