peerless-AV Xtreme/UV series User Manual
1
2015-10-15 #:180-9068-1
Xtreme™/UV™ – Series Displays
Peerless-AV® Waterproof Programmable
Remote Control
The Peerless-AV® Waterproof Universal Remote Control is pre-programmed with the latest library
of codes, and designed to operate the Peerless-AV Xtreme™/UV™ Displays, as well as third-party
Satellite and Cable Boxes, Blu-ray Players and DVD Players, VCR’s, Audio Equipment and various
Automation Equipment.
POWER
VCR SAT
TV
132
465
7
•
9
LAST
8
0
OK
DVD CBL AUX
MUTE SOURCE
VOL
REW
REC
PLAY
STOPFFPAUSE
MENU
GUIDE
CH
INFO
EXIT
2
2015-10-15 #:180-9068-1
Universal Remote Control Button Guide ................................................................................................3
Battery Installation and Replacement ....................................................................................................4
Device Table ...........................................................................................................................................5
Programming the Remote using Device Codes .....................................................................................5
Programming the Remote by Searching for Codes ................................................................................6
Manufacturer's Codes ............................................................................................................................6
Setup Codes for Cable Box ............................................................................................................6
Setup Codes for Satellite Receivers ...............................................................................................8
Setup Codes for TV's .....................................................................................................................9
Setup Codes for VCR & TV/VCR ................................................................................................13
Setup Codes for TV/VCR .............................................................................................................16
Setup Codes for DVD, DVR & Blu-ray .........................................................................................17
Setup Codes for DVR ...................................................................................................................19
Setup Codes for CD, LD, Home Automation, & PVR ...................................................................19
CONTENTS
3
2015-10-15 #:180-9068-1
Universal Remote Control Button Guide
POWER - Toggles Power On and Off
MUTE - Toggles Audio On and Off
SOURCE - Toggles through the available source inputs
TV - Press to control TV
DVD - Press to control DVD player
CBL - Press to control satellite or cable box functions
AUX - Press to control auxiliary equipment
NUMBERS - Discrete number commands
LAST - Press to return to previous channel
ARROWS - Press to navigate through menus and settings
OK - Press to select items in the menu or guide
VOL +/- - Press to increase or decrease volume
INFO - Press to display content information
EXIT - Press to exit the on-screen display menu
CH +/- - Press to change the channel up or down
REW - Rewind skips backward in content
PLAY - Press to start content play
FF - Press to Fast Forward & skip content ahead
MENU - Press to access the On-Screen Display Menu
REC - Press to Record content
STOP - Press to Stop content Play
PAUSE - Toggles between content Pause and Play
GUIDE - Press to access Guide information
POWER
VCR SAT
TV
132
465
7
•
9
LAST
8
0
OK
DVD CBL AUX
MUTE SOURCE
VOL
REW
REC
PLAY
STOPFFPAUSE
MENU
GUIDE
CH
INFO
EXIT
4
2015-10-15 #:180-9068-1
Battery Installation and Replacement
Remove the two screws from the battery holder as shown. Pull the battery holder out of the bottom of
the remote control and remove the batteries.
Insert two new 1.5V AAA batteries into the battery holder as shown. Ensure the positive and negative
marks on the batteries are correctly oriented with the markings on the inside of the remove control's
battery compartment.
Insert the battery holder back into the battery compartment of the remote control. Tighten both battery
holder screws, making sure the screws are tightened all the way to maintain a waterproof seal (do not
over tighten).
Note: The Peerless-AV Waterproof Universal Remote Control is supplied with batteries already
installed.
If the Red LED light on the remote fails to illuminate when a button is pressed, the batteries may need
to be replaced. Follow the directions below to replace the batteries.
5
2015-10-15 #:180-9068-1
Device Table
Programming the Remote using Device Codes
NOTE:
Please refer to Table 1a when in the "PROGRAMMING THE REMOTE USING DEVICE CODES"
section. After programming is complete, the Universal Remote Control will be able to control the
following types of devices:
To have universal control of your devices through the Peerless-AV Programmable Remote, perform
the following steps; otherwise skip this section. Fully read and understand the process before
attempting to program the remote.
If none of the listed codes work with your device, proceed to the "PROGRAMMING THE REMOTE BY
SEARCHING FOR CODES" section (page 6).
1. Turn on the device that you would like to program into your remote using the power button the
the device.
2. On the Peerless-AV Universal remote control, press and hold the button that you are trying to
program (TV, DVD, CBL, or AUX) and the OK button simultaneously for 2 seconds. The Red
LED on the remote will illuminate.
3. In the "MANUFACTURER'S CODES" section (page 6), locate the type and brand name of the
device you are trying to program into the remote. Once you have located it, enter the fi rst 3-digit
code for your device. If the device that you are trying to control turns off, press the Device button
that you were trying to program (TV, DVD, CBL, or AUX). The Red LED will blink two times.
4. To confi rm the code works properly, press the Device button again then press the Power button.
The device should turn on; however, if the device did not turn on, please repeat step 1-3 above
with the next code in the list for that manufacturer.
NOTE:
If Peerless-AV Display is unresponsive to commands being sent, press the TV button and send the
commands again.
Table1a
TV Controls the Peerless-AV Display
DVD Blu-ray, DVD, DVR, VCR, TV/VCR
CBL Cable Box, Satellite Box
AUX CD, LD, Home Automation, PVR Device
6
2015-10-15 #:180-9068-1
Programming the Remote by Searching for Codes
Manufacturer's Codes
CABLE BOX Codes
1. Turn on the device that you would like to program into your remote using the power button the
the device.
2. On the Peerless-AV Universal remote control, press and hold the button that you are trying to
program (TV, DVD, CBL, or AUX) and the OK button simultaneously for 2 seconds. The Red
LED on the remote will illuminate.
3. Press and release the CH Up button once to start the code search through the list of available
codes. Each time the CH Up button is pressed, the remote will send an Off command to the
device using the next code on the list. Each time the CH Up button is pressed, the Red LED on
the remote control will illuminate for verifi cation.
4. Continue pressing the CH up button until the device you are trying to control turns off. Then
press the Device button that you were trying to program (TV, DVD, CBL, or AUX). The Red LED
will blink two times.
5. To confi rm the code will work properly, press the Device button again. Then press the power
button. The device should turn on; However, if the device did not turn on, please repeat steps
1-4 above.
Brand Codes
ABC 107 109 113 117 131 135 144
ALLEGRO 112
ANTRONIX 045 121
ARCHER 045 121 130 132
CABLE TENNA 121
CABLE VIEW 121
CENTURY 132
COLOUR VOICE 002 003
COMTRONICS 039 110
CONTEC 114
DIRECTOR 202
GARRARD 132
GC ELECTRONICS 045
GEMINI 045 048
GENERAL INSTRUMENT 202 092 099 100 125 126 127 131 135
HAMLIN 139 142 145
HITACHI 135
HYTEX 144
JASCO 132
JERROLD 202 048 107 109 117 125 126 127 131 135
MAGNAVOX 111
MEMOREX 106
MOTOROLA 201 202
Loading...