Peerless-AV WL-PRG-UNV-200 Installation [en, es, fr]
Installing Wall Plate to Wood Stud Walls
r
r
A
k
for:
PA730, PP730, SA730P, SP730P, PA740, PP740, SA740P,
SP740P, SP735P, SA735P, PA735F, SP746P, SA746P, PA746F
Models: WSP700, WSP701
Max UL Load Capacity
80 lbs. (36 kg) 25 lbs. (11 kg)
SA740P SA730P
SP740P SP730P
PA740 PA730
PP740 PP730
SA746P SA735P
SP746P SP735P
PA746F PA735F
U
©
L
USC
WSP700
NOTE: Read entire instruction sheet before you start installation and assembly.
Before you begin, make sure all parts shown are included with your product.
WSP701
Parts List WSP700 WSP701
Description Qty. Part Numbe
wall plate 1 024-P1050 024-P1051
B wood screw #14 x 2.5 phillips hex head 4 5S1-015-C03 5S1-015-C03
C phillips screw, 1/4 - 20 x .5 blac
Parts may appear slightly different than illustrated.
2 520-1209 520-1209
Part Numbe
C
A
B
WSP700
WSP701
Tools Needed for Assembly
• stud fi nder ("edge to edge" stud fi nder is recommended)
• phillips screwdriver
• drill
• 5/32" (4 mm) bit for wood stud wall
• level
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 10-06-09 SHEET #: 095-9301-2 09-25-10
Wood Stud Installation
1
Use a stud fi nder to locate the edges of the studs.
Use of an edge-to-edge stud fi nder is highly
recommended. Draw a vertical line down the center
of each stud. Place wall plate (A) on wall as a
template. Level plate, and mark the center of the
four mounting holes. Make sure that the mounting
holes are on the stud centerlines.
(4 mm) dia. holes 2 1/2" (64 mm) deep. Attach wall
plate (A) using four wood screws (B).
WSP700
16"
WSP701
20"
Drill four 5/32"
WARNING
• Installer must verify that the supporting surface will
safely support the combined load of the equipment
and all attached hardware and components.
• Tighten wood screws so that wall plate is fi rmly at-
tached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into
the center of the stud. The use of an "edge to edge"
stud fi nder is highly recommended.
top fl ange
faces up
A
WSP701
24"
Mounting Arm Assembly to Wall Plate
2
Attach arm assembly (sold separately) to wall plate
(A) using screws (C) as shown.
ARM
ASSEMBLY
A
B
PA730, PP730, PP740, PA735F
SA730, SP730, SA740, SP740, SA735P, SP735P, SA746P, SP746P
C
Peerless Industries, Inc.
3215 W. North Ave.
Melrose Park, IL 60160
www.peerlessmounts.com
2 of 6
PA740, PA746F
ISSUED: 10-06-09 SHEET #: 095-9301-2 09-25-10
© 2009, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or regis-
tered trademarks of their respective owners.
Loading...