Peerless-AV WBK100 Installation
Installation and Assembly:
Wireless TV Cart for 47" to 65" Flat Panel Displays
Models: WL-SR560M-200
Max Load Capacity:
150 lb (68 kg) screen
50 lb (22.7 kg) per shelf
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
ISSUED: 08-24-12 SHEET #: 180-9037-2 10-30-12
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, and fully understands
these instructions.
• Never exceed the Maximum Load Capacity on page 1.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• The cart is not affi xed or secured to the fl oor, and may therefore tip over and/or fall if screen and/or stand is shaken
or hit. Always monitor children and do not let children play alone around stand as they could get hurt by a falling
screen. Not recommended for use in areas with heavy traffi c.
Tools Needed for Assembly
• level
• phillips screwdriver
Table of Contents
Parts List........................................................................................................................................................................ 3, 4, 5
Assembling Cart .....................................................................................................................................................................6
Wireless Receiver Assembly and Power Module Assembly Installation...............................................................................11
Installing Adapter Brackets ................................................................................................................................................. 12
Attaching Universal Adapter Plate .................................................................................................................................... ...14
Wireless Receiver Assembly and Power Module Assembly Setup.......................................................................................15
Cord Management ............................................................................................................................................................... 18
2 of 19
ISSUED: 08-24-12 SHEET #: 180-9037-2 10-30-12
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly different than illustrated.
Parts List
Description Qty.
screen mount bracket 1
A
hook plate 1
B
shelf support 1
C
base 1
D
universal plate 1
E
adapter bracket 2
F
upright 1
G
top cover 1
H
1/4-20 x 12mm decorative screw 22
I
1/4-20mm nut 10
J
WL-SR560M-200
Part Number
201-1156
201-1157
201-1158
009-1223
201-1110
201-1510
580-1180
590-1210
520-2325
530-1050
L 3/8-16 x 2.5" socket screw 3 520-9550
M 7/32" allen wrench 1 560-9715
N 4 mm allen wrench 2 560-9646
O 8/32 nylock nut 6 530-1038
P shelf pan 1 009-1225
Q 6 mm allen wrench 1 560-9716
R left leg 1 009-1296
S right leg 1 009-1295
T wheel caster 2 600-0044
U wheel caster/brake 2 600-0045
V joint connector nut 4 530-1037
W 3/8-16 x 1.5" screw bolt 4 520-1329
X M10 x .402 ID lock washer 3 540-9424
3/16 allen wrench
Z
wireless receiver assembly 1 180-1092
AA
power module assembly 1 180-1015
BB
enclosure mounting bracket, small 4 120-1195
CC
enclosure mounting bracket, large 4 120-1196
DD
lock nut 1/4-20 8 530-1021
EE
FF cable tie anchor
GG cable tie .187 x 7.5 lg.
HH cable tie .04 x 5.75 lg.
1 560-0071
2 590-9469
8 590-1168
2 560-9711
cable management sheath 1 590-9468
II
JJ M10 x 15 mm socket screw 4 520-9262
3 of 19
ISSUED: 08-24-12 SHEET #: 180-9037-2 10-30-12
Parts List continued
P
O
M
A
B
R
G
N
JJ
Z
U
Q
X
L
C
I
W
J
D
EE
F
FF
E
S
AA
T
V
H
CC
BB
DD
HH
GG
Some parts may appear slightly different than illustrated.
4 of 19
II
ISSUED: 08-24-12 SHEET #: 180-9037-2 10-30-12
Security Adapter Bracket Fasteners
S
M4 x 12 mm (6)
510-1079
M4 x 25 mm (4)
510-1082
I.D. .22" (5.6 mm) (4)
540-1057
M5 x 12 mm (4)
520-1064
M6 x 30 mm (4)
520-1067
M6 x 12 mm (4)
520-1050
M6 x 25 mm (4)
520-1211
I.D. .34" (8.7 mm ) (4)
540-1059
M8 x 15 mm (6)
520-1068
M8 x 25 mm (4)
520-1101
M6 x 20 mm (4)
520-9554
M8 x 40 mm (4)
520-1152
M5 x 25 mm (4)
520-1122
multi-washer (6)
580-1036
wireless transmitter (1)
(180-1202)
3v battery (1)
(180-0008)
Additional Wireless Components
vga to rca adapter (1)
(180-1006)
12v power adapter (1)
(180-1004)
plastic stand (1)
(180-1205)
ir fl asher (1)
(180-1009)
remote (1)
(180-1207)
hdmi cable (2)
(600-0234)
®
READY
Quick Start Guide
Step 7 While turning on the display device the HD Flow Pro Wireless Multimedia units will be going through the startup process. This process may
PRO WIRELESS MULTIMEDIA KIT
What’s in the Box
Installation and Setup
Step 1 Connect the Transmitter to the source devices
™
Disc player, set top box, gaming console, etc.).
(Blu-ray
Tip Repeat Steps
teps
3-11 to connect
ect
ne
more than one
Receiver unit
t
(HDS200-2,
HDS200-3,
HDS200-4).
Step 3 Connect the display device (TV, monitor, projector, etc.)
tthdil d i(TV it jt t)
to the Receiver.
Step 5 Power-up the HD Flow Pro Devices.
1. Plug in the power adapter for the Transmitter and the Receiver to nearby
available power outlets.
2. Plug in the power adapter end to the Transmitter and then to the Receiver.
3. The units will automatically turn-on. The average power-on/sync time
is approximately two minutes.
© 2012 Peerless Industries, Inc. Peerless-AV™ is a trademark of Peerless Industries, Inc. All rights reserved.
HD Flow™ is a trademark of I Do It, LTD. Other parties’ marks are the property of their respective owners. hdflow.com
take up to two minutes to complete. The Power/Link indicator lights on the Transmitter and the Receiver will be flashing at first. Flashing indicates
Model No. HDS200 (-2, -3, -4)
2
Minutes
that the units are establishing a secure connection. Wait until the connection is successfully established, indicated by the Power/Link indicator
light becoming solid.
1 x Transmitter
1 x IR Extender
1 x Receiver
1 x Component Adaptor
2 x Stand
2 x Power Adapter
1 x Remote Control
1 x Quick Start Guide
1 x IR Flasher
1 x Users Manual
Power/Source
Selection Button
Step 8 Select the output that connects the Receiver to the display using
Step 9 Turn on the desired source device that is connected to
the Power/Source Selection Button or the provided remote control.
the Transmitter.
The output indicator light will become solid and the HD Flow logo will
appear on the display device.
Tip The IR window
may be easier to
locate with a direct
light shining on
sections of the
front panel of the
component device.
A small flashlight
works well.
Power/Source
Step 2 Connect the provided IR Flasher to the IR-OUT port on the Transmitter.
Selection Button
Find the location of the IR window on your source device and adhere the
IR Flasher eye directly over the IR window on your source device.
NOTE: One IR Flasher eye is to be used for one component device.
Step 10 Select the desired source or device input on the Transmitter
Step 11 Play the source device content and enjoy up to Full HD 1080p
using the Power/Source Selection Button on the remote control.
wireless entertainment experience.
Troubleshooting Tips
Transmitter and/or Receiver Indicator Lights are all Blinking:
• Check the media source resolution. The display device must be able
to support the resolution of the media source that is being streamed.
• The HD Flow Pro units are establishing a connection. It can take
Utilizing the INFO button will allow you to see the resolution data that
up to two minutes for the HD Flow Pro units to establish a complete
the display device supports. If the display device supports the highest
connection. If after two minutes have passed and the units have not
resolution of 720p but the source device is outputting 1080p content,
established a connection, unplug the power cable, wait 30 seconds
the content needs to be down-scaled to the maximum resolution of the
and reconnect the power supply to the units.
display device, in this case 720p.
Transmitter or Receiver Power Indicator Light is OFF:
Step 4 Install the IR Extender by plugging in the provided IR Extender in to
the IR-IN port on the Receiver and adhering the other end of the IR Extender
to a vertical surface near the output device. Ensure that the IR Extender is in
a line of sight to the remote control that controls your source devices.
NOTE: For Multicast models, receivers two, three and four do not come with an IR Extender. Additional IR Extenders
(HDS-IRE) can be purchased separately; visit peerless-av.com for more information.
Step 6 Turn on your display device (TV, monitor, projector, etc.).
• Check and verify the power supply connection.
Transmitter Input Indicator Light Blinks:
• Make sure that your source device is turned ON and the cable
is properly connected.
• Verify that the Transmitter is set to the appropriate input port.
• Check the resolution from your source device. This may need to
be changed to a resolution supported by the HD Flow Pro Wireless
Multimedia Kit. Reference the Resolution Chart in the HD Flow Pro
Manual for compatibility. Reference your source devices’ manual
for instruction on changing the output resolution.
Receiver Power Indicator Light Blinks:
• Verify that the HD Flow Pro Transmitter and Receiver are within
the recommended range of 131 feet. Physical obstructions such as
walls, floors and ceilings between the Transmitter and Receiver may
decrease the strength of the connection signal and reduce the overall
transmission range.
If a connection has been established and the HD Flow logo can be seen
on the display device, but content is not playing:
• Make sure that the input/output cables are properly connected.
• Verify that the Transmitter is set to the appropriate input port.
Receiver Output Indicator Light Blinks:
• Make sure that your display device, source device and the HD Flow Pro units
are all turned ON and the Receiver is properly connected to the output device.
• Verify that the Receiver is set to the appropriate output port.
• Check the resolution setting of your source device. This may need to be
changed to a resolution supported by the HD Flow Pro unit. Reference
the Resolution Chart in the HD Flow Pro Manual for compatibility.
Reference your source devices’ manual for instruction on changing
the output resolution.
If the above troubleshooting tips do not resolve the issues for a unicast setup,
please reference the Factory Reset Section of the HD Flow Pro Manual. For a
multicast system configuration, please contact Peerless-AV Customer Care at
800-856-2112 for further instruction.
Warning Do not place the HD Flow
Pro units near other devices that
emit excessive amounts of heat.
Increased temperatures may
cause the HD Flow Pro Transmitter
or Receiver unit to malfunction
or stop working.
Quick Start Guide for HD Flow Pro Wireless Multimedia Kit - LIT-0906
install guide (1)
(LIT-0905)
User Manual and Installation Guide
Pro Wireless Multimedia Kit
Models:
HDS200
HDS200-2
HDS200-3
®
READY
HDS200-4
ISSUED: 06-12-12 SHEET #: 180-9023-1
instruction sheet (1)
(180-9023)
5 of 19
ISSUED: 08-24-12 SHEET #: 180-9037-2 10-30-12
Insert right leg (S) into base housing (D) as shown in fi g. 1.1. Then align holes in right leg with holes in base
1
housing (D). Fasten base housing to right leg using two 3/8-16 x 1.5" bolts (W) and two joint connectors (V). Tighten
using 3/16" allen wrench (Z) and 7/32" allen wrench (M) as shown in fi g.1.2.
NOTE: Left and right legs can be identifi ed by looking at the cart from the front.
Repeat for left side with left leg (R).
fi g. 1.1
D
fi g. 1.2
V
S
FRONT OF CART
W
FRONT OF LEG
Insert casters (U & T) into holes of support legs (R & S) and hand thread to secure. Attach casters with brake (U) to
2
the back of left and right support legs (R & S). Attach casters without brake (T) to front of support legs as shown.
NOTE: Lock brakes on casters to avoid sudden movements during installation.
S
R
U
6 of 19
S
T
HAND THREAD
HOLD WHEEL
ISSUED: 08-24-12 SHEET #: 180-9037-2 10-30-12
Loading...