peerless-AV UV491, UV551 User Manual

1
2016-04-21 #:220-9010-1
ULTRAVIEW™ OUTDOOR TELEVISION
MODEL:
UV491, UV551
www.peerless-av.com
2
2016-04-21 #:220-9010-1
System Installation And Electrical Requirements ..................................................................................3
Electrical Code ...............................................................................................................................3
Power Source ................................................................................................................................3
General Safety Precautions ...................................................................................................................4
FCC Caution ...................................................................................................................................5
FCC Statement ...............................................................................................................................5
Relevant Information .....................................................................................................................5
Set Up Instructions .................................................................................................................................7
Parts List ........................................................................................................................................7
Choosing your TV Location ............................................................................................................8
Removing Cord Cover ....................................................................................................................8
Connecting Cables .........................................................................................................................8
Replacing Cord Cover ...................................................................................................................9
Connecting To The Power Source ................................................................................................10
Prepare Y our TV For Mounting .....................................................................................................11
Prepare The TV For Usage ..........................................................................................................12
Battery Installation And Replacement ..........................................................................................12
Operating Instructions ..........................................................................................................................13
Power On/Off the TV ....................................................................................................................13
Onboard Controls .........................................................................................................................13
Navigating The On-Screen Menu ................................................................................................14
Picture .................................................................................................................................14
Audio ...................................................................................................................................14
Setup ...................................................................................................................................14
Time ....................................................................................................................................15
Lock .....................................................................................................................................15
Channel ................................................................................................................................15
(RS-232C) Serial Control Of The TV ...........................................................................................16
Tips ............................................................................................................................................17
Troubleshooting ............................................................................................................................17
Care Of Screen ...........................................................................................................................17
Mobile Telephone Warning ..........................................................................................................17
End Of Life Directives ..................................................................................................................17
License Agreement & Trademark Notice .....................................................................................17
Product Specifi cations .........................................................................................................................18
TV .............................................................................................................................................18
Power ..........................................................................................................................................18
TV Controller Features ................................................................................................................18
Environmental .............................................................................................................................18
Mechanical ..................................................................................................................................19
Input/Output Connections ............................................................................................................19
Warranty ..............................................................................................................................................20
CONTENTS
3
2016-04-21 #:220-9010-1
SYSTEM INSTALLATION AND ELECTRICAL REQUIREMENTS
Electrical Code
Note: To the display system installer: This reminder is provided to call attention to Article 820-44 of
the National Electric Code that provides guidelines for proper grounding and, in particular, specifi es that the cable ground shall be connected to the grounding system of the facility. Outlet shall be installed near the equipment and shall be easily accessible.
Note: Installation shall incorporate UL Listed external surge protection rated 2500 Vpk or less, for 150 to 300 Vac mains, installed in accordance with Article 285 of ANSI/NFPA 70 or applicable local codes.
Power Source
The TV must be connected to a main socket outlet with a protective grounding connection. The main plug is used as the disconnect device and shall remain readily accessible. This display operates on 100-240 volts 50-60 Hz, AC current. Insert the power cord into a 120 volts
60 Hz outlet. Never connect the TV to direct current or anything other than the specifi ed voltage. To prevent electric shock from the display, do not use with an extension cord, receptacle, or other
outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure.
Antenna discharge unit (NEC Section 810-20)
NEC National Electric Code
Ground clamp
Electric service
equipment
Ground clamps
Power service grounding electrode system (NEC Art 250 Part H)
Grounding conductors (NEC Section 810-21)
Antenna lead-in wire
Never remove the back cover of the TV as this can expose you to very high voltages and other hazards. If the TV does not operate properly, unplug the TV and call your authorized dealer or service center.
WARNING
4
2016-04-21 #:220-9010-1
Read before operating equipment
Thank you for purchasing our product. Before using it, please read this user manual carefully and follow the instructions correctly for safe operation. Please keep this manual handy for future reference. Also, please be sure to always include this user manual in the packaging when transferring or transporting this product to a different location.
Batteries Installed Warning
CAUTION - Danger of explosion if batteries are incorrectly replaced. Replace only with the same or
equivalent type. Even through the remote is designed for outdoor usage, the batteries should not be exposed to excessive heat due to sunlight, fi re or other heat sources.
CAUTION:
To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualifi ed to do so.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not defeat the safety purpose of the polarized or grounding type electrical plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the electrical cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as electrical-supply cord or plug is damaged, does not operate normally, or has been dropped.
Only use attachments/accessories specifi ed by the manufacturer.
In case of emergency such as fi re or electric shock caused by the product, immediately contact 911 or proper emergency police/fi re service agencies in your country.
If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.
Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
An outdoor antenna should not be located near overhead electrical lines or any electrical circuits.
If an outside antenna is connected to the receiver, confi rm that the antenna system is grounded to protect against voltage surges and built up static charges Section 810 of the National Electric Code, ANSI/NFPA No 70-1984, provides information with respect to proper grounding for the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.
Use properly rated electrical voltage. Use of non-rated voltage may cause fi re, electric shock and severe damages to the product.
Do not open the cabinet under any circumstances. High voltage inside of this product may cause electric shock.
Do NOT climb on the product.
GENERAL SAFETY PRECAUTIONS
RISK OF ELECTRICAL SHOCK
To reduce the risk of electric shock, do not disassemble the unit under any circumstances. No user serviceable parts inside. All product services should be done by the Peerless-AV certifi ed service personnel.
WARNING
5
2016-04-21 #:220-9010-1
Do NOT, under any circumstances, modify or disassemble this product as it may cause fi re, electric shock, or severe damages to the product. Also any unauthorized modifi cations made to the product automatically void product warranty.
Never touch antenna lines or wires, electrical cables or plugs when lightning or thunder is present as it may cause electric shock.
Any severe physical impact on the product may cause certain components to fall out of place within and break, which may cause fi re or electric shock. In such event, do not operate the product. Contact the manufacturer for support.
Periodically clean dust off the electrical plug to keep it clean and dry, ensuring proper and safe operation of the product.
Do NOT destroy, process, or place close to any heat source; do NOT bend or twist electrical cords, electrical plugs, cables, or wires with excessive force; do NOT place any heavy object on the TV as all of the above may cause damage resulting in fi re or electric shock.
Do NOT touch electrical plugs with wet hands.
Always make sure to plug in the electrical plug fi rmly and completely. Incompletely placed electrical plugs may cause fi re or electric shock due to built up heat emission.
Do NOT use any non-rated electrical sockets or power strips with many other devices jointly plugged in. The wire of non-designated capacity may cause fi re due to built up heat emission. Try to use a single, directly dedicated and rated GFCI electrical outlet for the product for safe operation.
In case of product malfunction or unusual events such as electrical burning smell, smoke, or loss of content signals on TV due to internal overheating, immediately turn off and unplug the electrical cord and contact the manufacturer.
Do NOT install the product in unstable locations or near moving objects, constantly vibrating equipment, or uneven surfaces. Follow mounting instructions properly for safe operation of the product as improper installation may cause products to fall.
Do NOT install the product near any poisonous gas or chemically unstable atmosphere as it may cause fi re.
Do NOT submerge TV in water.
Do NOT pressure wash TV. Although the IP55 rating protects against jets of water, high pressure force may compromise the TV.
Do NOT install the product near any strong magnetic or electrical current fi eld as it may cause re, electric shock, or severe damages to the product and the product may be subject to electromagnetic radiation, causing deterioration of the picture quality.
Do NOT leave any fi re source, such as candles, close to or on the product as it may be a cause for fi re or damages to the product.
Do NOT move or transport the product with any cables (electrical cables, content connectivity cables) plugged in to the source devices. Damages may occur to the cables, plugs, or jointing connectors of the cables due to forcible bending and stress, which may cause damages to the waterproof seal of the product, making it subject to fi re, electric shock, or shorted circuit.
When unplugging the electrical plug or other cables, always pull using the plug and not the cord. Improper pulling of the cords or cables may cause damage to the waterproof seal, making it subject to fi re, electric shock, or a shorted circuit.
Outdoor TVs should always be carried and supported by at least two persons.
Do NOT use any other electrical cords or connection cables than what is provided with the product or from the manufacturer directly. Use of untested, unauthorized, or substituted electrical cords or connection cables may be a cause for malfunction, fi re, electric shock, or severe damages to the product. Also such use of improper or undesignated electrical cords or connection cables will void product warranty.
Always leave the Power Off when plugging or unplugging the electrical cords or connection cables to avoid electric shock or damages to the product.
Do NOT use any chemical such as paint thinner or benzene to clean the product’s exterior. It may cause scratches on the surface, erasing proper indications, identifi cation labels, or instructions on the exterior, which may be a cause for misuse and improper operation of the product.
6
2016-04-21 #:220-9010-1
FCC CAUTION
To assure continued compliance and possible undesirable interference, ferrite cores may be used when connecting this TV to video equipment; and maintain at least 400mm (15.75 inches) spacing to other peripheral devices.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications; however, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
Relevant Information
Record your TV's model and serial number here for future reference. Keep this user manual in an accessible location in the event service is required.
Note: Your TV's serial number can be found on the box and underneath the rear cover plate.
Model Number ____________________________________
Serial Number ____________________________________
Please use the electrical cord provided with this display. If a electrical cord is not supplied with this equipment, please contact your supplier. Only plug equipment into receptacles with GFCI protection.
Peerless-AV is not responsible for any issues created by water present at the plug/receptacle insertion point.
CAUTION
7
2016-04-21 #:220-9010-1
SET UP INSTRUCTIONS
Parts List
UV491
Part #
UV551
Part #Description Qty
A television 1 180-W1338 180-W1339 B cord cover plate 1 180-W1340 180-W1340 C remote 1 410-1032 410-1032 D thumb screw 4 560-1397 560-1397 E display dust cover 1 591-0005 591-0006
C
(1)
A
(1)
E
(1)
B
(1)
D
(4)
remote
display display dust
cover
cord cover
plate
thumb screw
AUX
LAST
OK
INFO
+
EXIT
CBLDVD
MUTE
POWER
VCR SAT
SOURCE
TV
1
4
7
.
2
5
8
0
3
6
9
VOL
REW PLAY FF MENU
REC STOP PAUSE GUIDE
CH
Never apply pressure to the exterior of the LCD screen. The manufacturer's warranty does not cover user abuse or improper installations
All cables and cable covers MUST be connected and attached prior to installation on mount.
When routing cables through the cable entry make sure that the cables are formed in such a way as to remove any stress on the connectors.
Electrical installation shall be in accordance with the applicable parts of Chapter 8 of ANSI/ NFPA70.
CAUTION
8
2016-04-21 #:220-9010-1
RS-232C
Connecting Cables
Removing Cord Cover
Connect cables from the source devices to their appropriate connector on the display.
Remove (4) thumb screws (D) and cord cover (B) to access source connection panel. Do not disconnect lanyard.
Antenna or Cable
HDMI 2
Coaxial SPDIF
AV / Video
AV / Audio L
AV / Audio R
Component 1 / PR
Component 1 / PB
Component 1 / Y
HDMI 1
VGA
PC Audio
USB
Audio Out
HDMI 3
A
B
D (4)
br
Choose your TV location
The TV should be installed in a location where the screen will not be facing direct sunlight. Ideal TV placement is an area that is shaded by landscaping, structures, trees, awnings, or elevated patio cover. The operating temperature range of the TV is -24° to 122° F. Do NOT use the TV if ambient air temperature exceeds the operating temperature limits.
Do not install within 5 ft. from a body of water.
CAUTION
9
2016-04-21 #:220-9010-1
Replacing Cord Cover
1. Run cables across foam gasket block. Leave aproximately 1/2" (13mm) between cables to ensure a proper seal.
2. Replace cord cover (B) and (4) thumb screws (D). Fasten thumb screws until gasket on cord cover plate is fully compressed to back of television. Cables will seal between display's gasket and cord cover's gasket as cover is pressed into place. Route cables thought opening at end of cord cover.
B
D (4)
Ensure bend radius limits for cables do not exceed limits set by the manufacturer.
Ensure cables are seated properly in the cable gland to avoid potential damage to cables when cord cover is installed.
Do not remove lanyard that connects the cord cover to the display.
CAUTION
Do not overtighten screws
10
2016-04-21 #:220-9010-1
Connect To The Power Source
Connect power cord to GFCI outlet.
11
2016-04-21 #:220-9010-1
Prepare Your TV For Mounting
Note: Install cables prior to mounting your display. Cable entry cover may be obstructed once the
display is mounted. A mounting solution is not included and is sold separately. Contact your Peerless-AV representative
for an outdoor rated mounting solution for your particular application. For your safety, only install outdoor-rated mount that is suitable for the application and supports the
weight of the display. When mounting a display outdoors, use proper environmentally rated mounts to ensure longevity in harsh environments.
Examine the chart below to determine the mounting specifi cations for your TV:
B F
D
Model
Mounting Hole
Pattern
Required Mounting
Screws
UV491 400x300mm
(4) M8 screws
(12-20mm long)
UV551 400x300mm
(4) M8 screws
(12-20mm long)
Model A B C D E F G H
UV491
15.75"
(400mm)
11.81"
(300mm)
14.34" (364)
6.56"
(167mm)
44.43"
(1128mm)
25.93"
(659mm)
3.54"
(90mm)
.61"
(16mm)
UV551
15.75"
(400mm)
11.81"
(300mm)
17.32"
(440mm)
8.28"
(210mm)
50.38"
(1280mm)
29.55"
(751mm)
3.54"
(90mm)
.61"
(16mm)
REAR VIEW SIDE VIEW
A
E H
C G
12
2016-04-21 #:220-9010-1
The remote control is powered by two 1.5V AAA batteries installed at the factory.
To install or replace batteries:
1. To remove the battery module of the remote control, remove the two screws on the end of the battery module. Slide the battery module out of the remote control.
2. Insert two new “AAA” size batteries into the battery module.
3. Slide the battery module back into the remote control and reinsert the two screws in the end of the battery module.
Incorrect usage of batteries can result in leaks or bursting. Peerless-AV recommends the following battery use:
Do not mix battery brands.
Do not combine new and old batteries. This can shorten the battery life or cause liquid leakage of the batteries.
Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment.
Do not touch exposed battery acid as it may injure skin.
Remove the batteries if you do not intend to use the remote control for a long period of time.
CAUTION
Prepare The TV For Usage
1. Clean the TV with an approved screen cleaner and microfi ber cloth designated in the "Care of Screen" section. Do not use window cleaners or products containing ammonia.
Remote Control Battery Installation And Replacement
C
AUX
LAST
OK
INFO
+
EXIT
CBLDVD
MUTE
POWER
VCR SAT
SOURCE
TV
1
4
7
.
2
5
8
0
3
6
9
VOL
REW PLAY FF MENU
REC STOP PAUSE GUIDE
CH
AUX
LAST
OK
INFO
+
EXIT
CBLDVD
MUTE
POWER
VCR SAT
SOURCE
TV
1
4
7
.
2
5
8
0
3
6
9
VOL
REW PLAY FF MENU
REC STOP PAUSE GUIDE
CH
13
2016-04-21 #:220-9010-1
Power On/Off Your New TV
Power on your TV by using the remote control or the rear power button as shown below. The TV will power on but image may not appear for a few seconds as it completes its power up sequence.
Remote control
Point the remote control at the IR sensor located behind the Peerless-AV logo at the center of the TV and press the power button
Onboard Power Button
To power on the TV, press the power button on the back of the TV.
Rear Power Key
OPERATING INSTRUCTIONS
Onboard Controls
Direct Mode: Allows for quick access to source selection, volume settings and channel selection. Menu Mode: Press the Menu button to access Menu Mode and activate the On Screen Display
(OSD). For a description of OSD operation refer to the next section. The keypad buttons are assigned as indicated in the table below.
Menu Mode Direct Mode
On/Off On/Off
Auto Confi g Input Select
Right Volumn Up
Left Volumn Down
Menu Menu
Select Channel Up
- Channel Down
VOL
CH
M
14
2016-04-21 #:220-9010-1
Picture
Picture Mode Standard
Dynamic Theater Personal
Contrast 50
Brightness 50
Color 50
Tint 50
Sharpness 50
Color Temp. Normal
Cool Warm
Zoom Mode 16:9
Full Zoom Point To Point 4:3
3DNR Off
Weak Middle Strong
Audio
Equalizer Standard
Music Movie
Sport Personal
120 Hz 50 500 Hz 50
1.5 KHz 50 5 KHz 50
10 KHz 50
Audio Language English
Spanish French
Digital Output
(SPDIF)
PCM/Raw
Surround On/Off
AVC On/Off
Navigating The On Screen Menu
Pressing the menu key on the remote or the onboard controls will cause the On Screen Display (OSD) main page to be displayed with fi ve menu tabs: Picture, Audio, Time, Setup, Lock and Channel. Use the cursor keys to move through the various sub menus. Pressing the menu key again will move the selection back one level. Press exit to quit.
Setup
Menu
Languages
English Spanish French
Transparency
(Menu
Transparency)
0% 25% 50% 75% 100%
Restore Defaults Factory Reset All Options
Setup Wizard
Software Update (USB) Blue Screen On/Off HDMI MODE Video
PC
15
2016-04-21 #:220-9010-1
Navigating The On Screen Menu
Pressing the menu key on the remote or the onboard controls will cause the On Screen Display (OSD) main page to be displayed with fi ve menu tabs: Picture, Audio, Time, Setup, Lock and Channel. Use the cursor keys to move through the various sub menus. Pressing the menu key again will move the selection back one level. Press exit to quit.
Time
Sleep Timer off
5min 10min 15min 30min 60min 90min 120min 180min 240min
Time Zone Select time zone
DST On/Off
Time Format 12-hour
24-hour
Auto Sync On/Off
Clock Enter Current Time
Wake Up Enter desired time when
display will turn on
NO SIGNAL
SHUT
On/Off
Lock
System Lock Enter Password to lock
the menu
Channel
Air/Cable Choose between Antenna
and Cable
Auto Scan Searches for available
channels
Favorite Shows favorite channels
Show/Hide show or hide channels
Channel No. Displays list of channels
Channel Label Change channel names
DTV Signal Displays channel info and
signal strength
16
2016-04-21 #:220-9010-1
(RS-232C) Serial Control Of The TV
Attach an RS-232C cable (straight through type) to the supplied D-Sub RS-232C for the connections. Note: This operation system should be used by a person who is accustomed to using computers.
Menu: Right: OK: Down: Up: Left: Source: (1): (2): (3): (4): (5): (6): (7): (8): (9): (0): Exit: Power On: Power Off: Power On/Off: Volume +: Volume -: Channel +: Channel -:
Mute: Sleep: AV: VGA: HDMI Toggle: HDMI1: HDMI2: HDMI3: S-VIDEO: TV: DTV: Component: USB: PMODE: Zoom: Surround: SMODE: VOL 25%: VOL 50%: VOL 75%: VOL 100%: Brightness 25%: Brightness 50%: Brightness 75%: Brightness 100%:
A0, F0, 55, FF, 4E, B1 A0, F0, 55, FF, 05, FA A0, F0, 55, FF, 02, FD A0, F0, 55, FF, 0D, F2 A0, F0, 55, FF, 17, E8 A0, F0, 55, FF, 0C, F3 A0, F0, 55, FF, 01, FE A0, F0, 55, FF, 42, BD A0, F0, 55, FF, 43, BC A0, F0, 55, FF, 0F, F0 A0, F0, 55, FF, 1E, E1 A0, F0, 55, FF, 1D, E2 A0, F0, 55, FF, 1C, E3 A0, F0, 55, FF, 18, E7 A0, F0, 55, FF, 45, BA A0, F0, 55, FF, 4C, B3 A0, F0, 55, FF, 56, A9 A0, F0, 55, FF, 1B, E4 A0, F0, 55, FF, AE, 51 A0, F0, 55, FF,AD, 52 A0, F0, 55, FF, 0B, F4 A0, F0, 55, FF, 0A, F5 A0, F0, 55, FF, 40, BF A0, F0, 55, FF, 55, AA A0, F0, 55, FF, 5A, A5
A0, F0, 55, FF, 14, EB A0, F0, 55, FF, 53, AC A0, F0, 55, FF, ED, 12 A0, F0, 55, FF, EA, 15 A0, F0, 55, FF, EC, 13 A0, F0, 55, FF, DE, 21 A0, F0, 55, FF, DF, 20 A0, F0, 55, FF, E0, 1F A0, F0, 55, FF, E4, 1B A0, F0, 55, FF, E8, 17 A0, F0, 55, FF, E9, 16 A0, F0, 55, FF, E7, 18 A0, F0, 55, FF, 57, A8 A0, F0, 55, FF, 4B, B4 A0, F0, 55, FF, 51, AE A0, F0, 55, FF, C7, 38 A0, F0, 55, FF, 5B, A4 A0, F0, 55, FF, 21, DE A0, F0, 55, FF, 22, DD A0, F0, 55, FF, 23, DC A0, F0, 55, FF, 24, DB A0, F0, 55, FF, 26, D9 A0, F0, 55, FF, 27, D8 A0, F0, 55, FF, 28, D7 A0, F0, 55, FF, 29, D6
COM Settings Baud Rate 38400 Data Bits 8 Parity None Stop Bits 1
17
2016-04-21 #:220-9010-1
Care Of The Screen
Do not rub or strike the screen with anything hard as this may scratch, mark, or even damage the screen permanently. Ensure that the TV is installed in a location where it will be safe from abrasives
and fl ying debris, which could damage the LCD panel. Never use ammonia or any product containing ammonia, as it will damage the anti-glare coating on the face of the TV. Only use an approved screen cleaner to clean the display face. Unplug the power cord before cleaning the screen. Dust the display by wiping the screen and the
cabinet with a soft, clean cloth and if the screen requires additional cleaning, use a clean, damp cloth. Do not use liquid cleaners, aerosol cleaners, or solvents of any kind.
To prolong the life of the TV, install the dust cover when the TV is not is use.
Mobile Telephone Caution
Keep your mobile telephone away from your display to avoid disturbances in the picture or sound, possibly causing permanent damage to your TV.
End Of Life Directives
In an effort to produce environmentally friendly products. Your new TV contains materials that can be recycled and reused. At the end of your TV life, specialized companies can minimize TV waste by separating reusable materials from non-reusable materials. Please ensure you dispose of your TV according to local regulations.
License Agreement And Trademark Notice
Troubleshooting
TIPS
No Picture • Check that the TV is turned on.
• Is the power cord inserted into a power outlet?
• Test the power outlet by plugging in another device into the outlet.
Remote Control
Doesn’t Work
• Make sure there is a direct path between the remote control and the IR receiver located at the Peerless-AV logo at the bottom center of the TV.
• Press the “TV” button on the universal remote control to select the TV as the device being controlled.
• Was the shipping tab removed and the battery re-installed correctly?
• Install new battery.
®
HDMI, the HDMI logo and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Manufactured under license from Dolby Labratories, Dolby and the double-D symbol are trademarks of Dolby Labratories
18
2016-04-21 #:220-9010-1
Specifi cations subject to change without notice
PRODUCT SPECIFICATIONS
Display
Screen Size 49", 55" diagonal
Aspect Ratio 16:9
Resolution 1920 x 1080 Brightness 500 cd/m
2
Contrast Ratio* 1300:1
Viewing Angle 178° vertical/horizontal
Response Time 8ms (gray to gray)
Refresh Rate 60 Hz
TV Controller Features
Analog TV NTSC
Digital TV ATSC/256QAM
Picture
Adjustment
Brightness/Contrast/ Tint/Sharpness/Noise reduction
Picture Mode Standard, Dynamic,
Theater, Personal
Color
Temperature
Adjustment
Cool, Normal, Warm
Screen
Adjustment
16:9/Full/Zoom/Point to Point/4:3
Clock, Sleep
Timer
Yes
MTS Yes
V-chip Yes
Closed Caption Yes
Electronic
Program Guide
Yes
Noise Reduction Yes
3-D Comb Filter
and De-interlace
Yes
Mute Yes
OSD Language English, French, Spanish
* Enhanced for direct sunlight usage.
Power
AC Input 100 VAC to 240 VAC,
50 to 60 Hz
Environmental
Operating
Temperature
-24° F to 122° F
Storage
Temperature
0° F to 124° F
IP Rating IP55
Safety/EMC FCC Class B
19
2016-04-21 #:220-9010-1
Input/Output Connections
TV Input Coax (x1), 75 ohm, NTSC,
ATSC, 64 QAM, 256QAM
VGA Input 15 pin D-SUB (x1), Up to
1920x1080@60HZ
HDMI Input HDMI (x3), 480i, 480p,
576i, 576p, 720p, 1080i, 1080p
CVBS Input RCA (x1)
YPbPr Input RCA (x1), 480i, 480p,
720p, 1080i
VGA Stereo Audio Input
3.5mm Analog Audio (x1)
CVBS Stereo
Audio Input
RCA (x1)
YPbPr Stereo
Audio Input
RCA (x1)
Audio Stereo 3.5mm Stereo (x1)
Output 3.5mm Stereo Headphone
(x1)
RS232 Control 9 pin D-SUB (Female) (x1)
S/PDIF Digital
Audio Output
RCA (x1)
Mechanical
Display Size:
UV491
UV561
(W x H x D)
44.4" x 25.9" 4.15" (1128mm x 658mm x
105mm)
50.4" x 29.6" x 4.15" (1280mm x 752mm x
105mm)
Enclosure Color Black
VESA Mount
UV491 UV551
400x300mm 400x300mm
Net Weight
UV491 UV551
53 lbs (24.04kg) 63 lbs (28.58kg)
Shipping Size
UV491
UV551
(W x H x D)
48.38" x 29.87" x 7" (1228mm x 758mm x
178mm)
54.7" x 33.4" x 7" (1389mm x 848mm x
178mm)
Shipping Weight
UV491 UV551
58 lbs (26.31kg) 70 lbs (31.75kg)
LIMITED TWO-YEAR WARRANTY
TWO-YEAR PARTS & LABOR LIMITED WARRANTY Terms of Peerless-AV®
The Peerless-AV Outdoor TV/Display is warrantied to be free of defects in material and workmanship from the time of purchase by the original owner. If this product is found and proved to be defective under the terms and conditions of this warranty, Peerless-AV will repair or replace defective parts with new and/ or reconditioned parts at no charge for the parts and labor to the original owner, subject to the terms and conditions of this Limited Warranty. This Limited Warranty covers failures due to defects in material and workmanship that occur during normal residential or commercial use as follows:
Parts – the warranty period for parts is: two (2) years from the date of original purchase. During the applicable Limited Warranty period for parts, defective parts will be replaced at no charge. Parts used for the replacement will be warranted for the remainder of the original warranty period for those parts.
Labor – the warranty period for labor is: two (2) years from the date of original purchase. During the applicable Limited Warranty period for labor, Peerless-AV will provide the labor for warranty repair at no charge for a period of two (2) years from the date of original purchase.
Original owner must provide verifi cation of the date of purchase when requesting Limited Warranty Services. A copy of the original Dated Sales Receipt is required together with the product to obtain service under this Limited Warranty.
All repairs must be performed by a Peerless-AV Authorized Service Provider.
Customer is responsible for returning (including any freight and shipping costs) defective unit to a Peerless-AV Authorized Service Provider. If the product is found to have no defects, the customer will be responsible for return shipping costs as well.
THIS LIMITED WARRANTY DOES NOT COVER:
Labor to uninstall and reinstall the display / TV
• Shipping damage.
Damage caused during customer unpacking, and/or removal of packing materials.
Damage due to improper, incorrect or insuffi cient AC voltage.
Damage due to power surges or lightning strikes.
Damages which results from fi re, fl ood, lightning, tornado, hurricane, large hail, extremely gusty winds, sand storms, vandalism, terrorism or other acts of nature.
Any unit which has been modifi ed or damaged due to improper installation or failure to obey the operating instructions in the User Manual.
Any failure, loss, damage or personal injury due to accident, neglect, misuse, abuse, improper orientation, improper maintenance, improper storage, alteration to the unit, or failure by the consumer to follow operating instructions provided by the user manual.
Any owner other than the original owner.
Any unit purchased from an unauthorized seller.
If the original product serial number has been removed, defaced or tampered with in any way.
Any packaging or transportation charges incurred in connection with warranty services.
Indirect, consequential, or special damages except as required by federal or state laws.
Any unit tampered with, modifi ed, adjusted or repaired by any party other than the Peerless-AV Authorized Service Provider.
Any cosmetic damages to the surface or exterior that has been defaced or faded, or caused by normal wear and tear or exposure to chemicals, acid rain, large hail or adverse weather conditions.
Minor cabinet blemishes or minor scratches to the exterior of the unit or other cosmetic imperfections that are not within the viewing area of the LCD
Picture quality when installed in direct sunlight where sun is shining directly on the face of the LCD.
Any damage, scratches or blemishes to the face of the LCD and/or exterior cabinet due to end-user cleaning.
Dirty air waves, and/or unusual signal interference due to weak signal from multi-wire runs or weak signal from cable or satellite service providers or unusual signal interference or lack of distance when using the Digital Wireless Video/ Audio Package.
Return shipping when no defect is found.
Peerless-AV and its representatives or agents shall in no event be liable for any general, indirect or consequential damages arising out of/or caused by the use of /or the inability to use this product.
This warranty is made in lieu of all other warranties, expressed or implied, and all other liabilities on the part of Peerless-AV. Any other warranties, including the warranties of merchantability and fi tness for a particular purpose are hereby disclaimed by Peerless-AV and its representatives and/or agents.
All warranty inspections and repairs must be performed by Peerless­AV or its authorized service representations.
Customer Care: 800.865.2112 or 630.375.5100 Website: www.peerless-av.com
© 2016 Peerless Industries, Inc. All rights reserved.
Peerless-AV Europe
Unit 3 Watford Interchange, Colonial Way, Watford, Herts, WD24 4WP, United Kingdom Customer Care 44 (0) 1923 200 100 www.peerless-av.com
© 2016, Peerless Industries, Inc.
Peerless-AV de Mexico
Ave de las Industrias 413 Parque Industrial Escobedo Escobedo N.L Mexico 66050 Servicio al Cliente 01-800-849-65-77 www.peerless-av.com
© 2016, Peerless Industries, Inc.
Peerless-AV
2300 White Oak Circle Aurora, IL 60502 Email: tech@peerlessmounts.com Ph: (800) 865-2112 Fax: (800) 359-6500 www.peerless-av.com
© 2016, Peerless Industries, Inc.
Loading...