Peerless-AV TVF637 Installation
Installation and Assembly VCR Mount for Jumbo® Mounts
INSIDE DIMENSIONS
MODEL # WIDTH (W) HEIGHT (H)
VPM35-J, VPM35-JS, SVPM35-J, SVPM35-JS 10.25" - 14.25" (260 mm - 362 mm) 2.69" - 4.5" (68 mm - 114 mm)
VPM40-J, VPM40-JS, SVPM40-J, SVPM40-JS 13.25" - 17.25" (337 mm - 438 mm) 2.69" - 4.5" (68 mm - 114 mm)
VPM45-J, VPM45-JS, SVPM45-J, SVPM45-JS 13.25" - 17.25" (337 mm - 438 mm) 4.25" - 5.75" (108 mm - 146 mm)
Models:
VPM35-J, VPM35-JS, VPM40-J, VPM40-JS,
VPM45-J, VPM45-JS, SVPM35-J, SVPM35-JS,
SVPM40-J, SVPM40-JS, SVPM45-J, SVPM45-JS
C
A
B
N
Parts List
VPM35-J, VPM35-JS
SVPM35-J, SVPM35-JS
VPM40-J, VPM40-JS
SVPM40-J, SVPM40-JS
D
!
!
!
!
F
!
!
Parts may appear slightly different than illustrated.
There was an enhancement made to the JumboTM and Jumbo 2000TM TV mounts in 1999 to allow the VCR mount to
be added after the TV has been installed. Depending on the style you are using, you will complete your installation
one of the following two ways. As a result, you will not use all of the fasteners provided.
Follow this installation if your TV mount has slots in the center
of the tray rather than threaded holes. If you have this style, the
TV will have to be removed to complete the installation
of the VCR mount.
!
!
!
!
!
!
!
!
!
!
!
!
!
Check parts list. Be sure all parts listed are included with your product.
Note: The PentaPin tool is only included with security models (SVPM models)
VPM45-J, VPM45-JS
!
!
!
!
!
!
!
!
!
!
!
!
!
Description
SVPM45-J, SVPM45-JS
10-24 x 1/2 carriage bolt
A
!
10-24 nylock nut
B
!
#10 SAE flat washer
C
!
M5 x .8 x 8 mm phillips screw
D
!
penta-pin tool (not shown)
E
!
VCR Bracket
F
!
hanger bracket
N
!
Follow this installation if your TV mount has four threaded holes
in the center of the tray . The TV does not have to be removed
for you to install your VCR mount.
Black
Part Number
Qty.
520-9523
8
530-9341
8
540-9400
8
520-1167
8
520-9249
1
1
1
1255-275
Silver
Part Number
520-2104
530-9342
540-9442
520-2167
520-9249
081-4086
A
Attach VCR as
1
shown using parts
N, A, B, C, and D.
N
Attach VCR as
1
shown using parts
N, and D.
N
C
B
D
D
Adjust the VCR mount
2
as shown to fit your
equipment.
1 of 2
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
ISSUED: 5-25-95 SHEET #081-9002-5 09-10-04
OPTIONAL: If attaching multiple VCR mounts to a TV mount, proceed with step 3 through 5.
IMPORT ANT! Do not stack more than three VCR Mounts from a single Peerless TV Mount!
IMPORTANT! Stacked load can not exceed 50 lb.
Insert four carriage bolts (A) into slots in upper VCR
3
Mount. Att ach lower VCR Mount using four nuts (B) and
four washers (C). HAND TIGHTEN ONL Y .
Note: if adhesive pads on VCR Mount are covering
slots, trim away excessive pad to expose slots.
A
slots
adhesive pad
Align front of VCR with front of TV on TV Mount
5
above (TV Mount not pictured). Tighten expansion
screws in sides and bottom of VCR Mount to
clamp the VCR with a firm, secure grip.
Note: To access the vertical expansion screws
located on the bottom of the upper VCR Mount,
slide the lower VCR Mount to the side exposing
vertical expansion screw. Repeat this step on
opposite side of VCR Mount. Center lower VCR
Mount and tighten four nuts (B, see step 3)
securely .
Expand lower VCR Mount to slightly larger than
the height and width of the VCR that it will hold.
Insert and clamp lower VCR into lower VCR
Mount.
C
B
Insert VCR into upper VCR Mount.
4
2 of 2
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 5-25-95 SHEET #081-9002-5 09-10-04
Peerless and Jumbo are registered trademarks of Peerless Industries, Inc.
© 2004 Peerless Industries, Inc. All rights reserved.
Loading...