Peerless-AV TVF624 Installation
Installation and Assembly VCR Mount for Slimline Standard Wall Mount
Models:
VPM35-W, VPM40-W , VPM45-W ,
SVPM35-W, SVPM40-W , SVPM45-W
INSIDE DIMENSIONS
MODEL # WIDTH (W) HEIGHT (H)
VPM35-W, SVPM35-W 10.25" - 14.25" (260mm - 362mm) 2.69" - 4.5" (68mm - 114mm)
VPM40-W, SVPM40-W 13.25" - 17.25" (337mm - 438mm) 2.69" - 4.5" (68mm - 114mm)
VPM45-W, SVPM45-W 13.25" - 17.25" (337mm - 438mm) 4.25" - 5.75" (108mm - 146mm)
E
G
F
D
Place hanger bracket (L)
1
over end of TV mount arm
as shown. Attach using
four screws (B).
L
B
Slimline Wall
Arm support
arm
Parts List
VPM35-W
SVPM35-W
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
VPM40-W
SVPM40-W
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
VPM45-W
SVPM45-W
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
Description
M5 x .8 x 10mm phillips screw
B
penta-pin tool (not shown)
C
VCR bracket
D
10-24 x 1/2 carriage bolt
E
10-24 nylock nut
F
#10 SAE flat washer
G
hanger bracket
L
Parts may appear slightly different than illustrated.
Check parts list. Be sure all parts listed are included with your product.
Note: The PentaPin tool is only included with security models (SVPM models)
Adjust the VCR mount
2
with screwdriver as
shown to fit your
equipment.
Qty.
4
1
1
4
4
4
1
Part Number
520-1030
520-9249
520-9523
530-9341
540-9400
1245-271
L
B
1 of 2
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
ISSUED: 5-25-95 SHEET #: 081-9005-2 04-02-02
OPTIONAL: If attaching multiple VCR mounts to a TV mount, proceed with step 3 through 5
IMPORT ANT! Do not stack more than three VCR Mounts from a single Peerless TV Mount!
IMPORTANT! Stacked load can not exceed 50lbs.
Insert four carriage bolts (E) into slots in upper VCR
3
Mount. Attach lower VCR Mount using four nuts (F) and
four washers (G). HAND TIGHTEN ONLY.
Note: if adhesive pads on VCR Mount are covering
slots, trim away excessive pad to expose slots.
E
slots
adhesive pad
Align front of VCR with front of TV on TV Mount
5
above (TV Mount not pictured). Tighten expansion
screws in sides and bottom of VCR Mount to
clamp the VCR with a firm, secure grip.
Note: T o access the vertical expansion screws
located on the bottom of the upper VCR Mount,
slide the lower VCR Mount to the side exposing
vertical expansion screw. Repeat this step on
opposite side of VCR Mount. Center lower VCR
Mount and tighten four nuts (F, see step 3)
securely .
Expand lower VCR Mount to slightly larger than
the height and width of the VCR that it will hold.
Insert and clamp lower VCR into lower VCR
Mount.
G
F
Insert VCR into upper VCR Mount.
4
2 of 2
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
© 2002 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark of Peerless Industries, Inc.
ISSUED: 5-25-95 SHEET #: 081-9005-2 04-02-02
Loading...