Peerless Industries ST650P, ST650P-S, ST650-S, ST650 User Manual

Installation and Assembly:

Smartmount

Universal Tilt Wall Mount for LCD and

Plasma 32" to 50" Flat Panel Screens

Models: ST650, ST650-S, ST650P, ST650P-S

This product is intended for use with UL

Listed products and must be installed by a qualified professional installer.

Maximum UL Load Capacity: 175 lb (79kg)

Features:

• Open wall plate design allows for additional wall access, increasing electrical access and cable management options

• Universal screen mounting brackets hook onto the wall plate for quick, easy , and safe installation

• Adjustable up to 15° of forward tilt and up to -5° backward tilt

• One-touch tilt for effortless adjustment

• Pre-tensioned universal tilt bracket allows for tilt angle adjustment in one easy motion.

• Easy grip handle locks the screens position into place

• Optional IncreLok feature offers fixed tilts at -5°, 0°, 5°, 10° and 15° increments

• Includes Sorted-For-Y ou™ fastener pack for installation to wood studs, concrete and cinder block

• Optional horizontal adjustment of up to 8" (depending on screen model) for perfect screen placement

• Available in Black and Silver

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 11-21-07 SHEET #: 202-9255-2 02-22-08

NOTE: Read entire instruction sheet before you start installation and assembly .

WARNING

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-21 12.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

• Never exceed the Maximum UL Load Capacity . See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly , but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.

• This product was designed and intended to be mounted to the following supporting surfaces checked below with the hardware included in this product as specified in the installation sheet. To mount this product to an alternative supporting surface, contact Peerless customer care at 1-800-865-21 12.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED x Wood Stud None

x Wood Beam None x Solid Concrete None x Cinder Block None

Metal Stud Do not attach except with Peerless accessory kit for metal studs;

Contact Customer Service for Peerless accessory kit for metal studs. Brick Contact Customer Service Other or unsure? Contact Customer Service

Tools Needed for Assembly

• stud finder ("edge to edge" stud finder is recommended)

• phillips screwdriver

• drill

• 1/4" bit for concrete and cinder block wall

• 1/2" bit for metal stud wall

• 5/32" bit for wood stud wall

• level

Accessories

• ACC415 - Metal S tud Fastener Kit (Metal S tud not

evaluated by UL)

• SCS221- SmartMount® A/V Component Shelf

Table of Contents

Parts List..............................................................................................................................................................................3

Installation to Double Wood Stud Wall..................................................................................................................................5

Installation to Solid Concrete or Cinder Block .......................................................................................................................6

Installing Adapter Brackets...................................................................................................................................................7

Mounting and Removing Flat Panel Screen...........................................................................................................................9

For customer care call (800) 865-21 12 or (708) 865-8870.

2 of 27

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

ISSUED: 11-21-07 SHEET #: 202-9255-2 02-22-08

Before you begin, m ake sure all part s shown are inc l uded with your produc t .

Parts List

Description

wall plat e 1

right ad apter br acket 1

left adapt e r br acket 1

#14 x 2.5" wood scre w

Alligator

4 mm allen wrenc h

Parts may appear slightly different than illustrated.

anchor

AA BB

Security No n -Se cu rity

B lack Part

Qty.

Number

201-1504 201-4504 201-1504 201-4504 201-1470 201-4470 201-1469 201-4469 201-1472 201-4472 201-1471 201-4471

5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03 590-0097 590-0097 590-0097 590-0097

4 1

560-1146 560-1146 N/A N/A

Silver Part Number

Black Part Number

Silver Part Number

Non-SecurityAdapter Bracket Fasteners

NOTE: The sorted-for-you™ fastener pack included was made specifically for your product and may not contain all components

shown below.

M4 x 12 mm (6)

(504-9013)

M4 x 25 mm (4)

(504-1015)

M8 x 16 mm (6)

(520-9257)

M6 x 30 mm (4)

(510-9109)

M5 x 12 mm (4)

(520-1027)

M8 x 40 mm (4)

(520-1 136)

M5 x 25 mm (4)

(520-9543)

M8 x 25 mm (4)

(520-1031)

M6 x 12 mm (4)

(520-1 128)

I.D. .34" (8.6 mm) (4)

(540-1059)

I.D. .22" (5.6 mm) (4)

M6 x 20 mm (4)

(520-9402)

(540-1057)

M6 x 25 mm (4)

(520-1208)

multi-washer (6)

(580-1036)

3 of 27

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

ISSUED: 11-21-07 SHEET #: 202-9255-2 02-22-08

Security Adapter Bracket Fasteners

NOTE: The sorted-for-you™ fastener pack included was made specifically for your product and may not contain all components

shown below.

M4 x 12 mm (6)

(510-1079)

M8 x 15 mm (6)

(520-1068)

I.D. .22" (5.6 mm) (4)

(540-1057)

M4 x 25 mm (4)

(510-1082)

M8 x 40 mm (4)

(520-1 152)

I.D. .34" (8.6 mm) (4)

(540-1059)

M5 x 12 mm (4)

(520-1064)

M6 x 20 mm (4)

(520-9554)

M5 x 25 mm (4)

(520-1 122)

M6 x 30 mm (4)

(520-1067)

M6 x 12 mm (4)

(520-1050)

M8 x 25 mm (4)

(520-1 101)

M6 x 25 mm (4)

(520-121 1)

multi-washer (6)

(580-1036)

4 of 27

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

ISSUED: 11-21-07 SHEET #: 202-9255-2 02-22-08

Installation to Double Wood Stud Wall

WARNING

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations.

Wall plate (AA) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.

Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each stud’s center . Place wall plate on wall as a template. The top mounting slot s should be located 6.2" (157.5 mm) above the desired screen center as shown in figure 1.1. Level plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using four #14 x 2.5" wood screws (DD) as shown in figure 1.2.

NOTE: Wall plate may be mounted up to 4" (102 mm) off center as shown in figure 1.1.

Skip to step 2 on page 7.

STUD

(157.5 mm)

CS = center of screen

(102 mm)

6.2"

fig. 1.1

fig. 1.2

5 of 27

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

ISSUED: 11-21-07 SHEET #: 202-9255-2 02-22-08

Installation to Solid Concrete or Cinder Block

WARNING

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity .

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor .

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Make sure that wall plate (AA) is level, use it as a

template to mark four mounting holes. The top mounting slots should be located 6.2" (157.5 mm) above the desired screen center as shown in figure 1.1 page 5. Drill four 1/4" (6 mm) dia. holes to a minimum depth of

2.5" (64 mm). Insert anchors (EE) in holes flush with wall as shown (right). Place wall plate over anchors and secure with #14 x 2.5" screws (DD). Level, then tighten all fasteners.

WARNING

• Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

• Always attach concrete anchors directly to loadbearing concrete.

• Never attach concrete anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer .

concrete surface

Drill holes and insert anchors (EE).

Place plate (AA) over anchors (EE) and secure with screws (DD).

Tighten all fasteners.

solid concrete

cinder block

CORRECT

concrete

CUT A WAY VIEW

wall

plate

plaster/ dry wall

INCORRECT

concrete

wall plate

plaster/ dry wall

6 of 27

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

ISSUED: 11-21-07 SHEET #: 202-9255-2 02-22-08

Installing Adapter Brackets

WARNING

• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.

To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place

screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached. Place adapter brackets (BB or CC) on back of screen, align to holes, and center on back of screen as shown below. Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multi-washers, and spacers as shown in figure 2.1 or 2.2.

NOTE: Top and bottom holes of screen must always be used. Verify that all holes are properly aligned, and then tighten screws using a phillip s screwdriver.

MULTI-WASHER

CENTER BRACKETS

VERTICALLY ON BACK

OF SCREEN

NOTE: "X" dimensions should be equal.

MEDIUM HOLE FOR M5 SCREWS

SMALL HOLE FOR M4 SCREWS

LARGE HOLE FOR M6 SCREWS

HANDLES

FACE OUT

Notes:

• The number of fasteners used will vary, depending upon the type of screen.

• Multi-washers and spacers may not be used, depending upon the type of screen.

• Use the corresponding hole in the multiwasher that matches your screw size as shown.

NOTE: For flat back screens proceed to step 2-1. For bump-out or recessed back screen skip to step 2-2.

7 of 27

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

ISSUED: 11-21-07 SHEET #: 202-9255-2 02-22-08

For Flat Back Screen

Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2

2-1

for a full screen compatibility chart for this mount. Begin with the shortest length screw, hand thread through multi-washer and adapter bracket (BB or CC) into screen

as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.

NOTE: Spacers may not be used, depending upon the type of screen.

fig 2.1

SCREEN

MUL TI-WASHER

SCREW

ADAPTER BRACKET

(BB or CC)

If you have any questions, please call Peerless customer care at 1-800-865-2112.

For Bump-out or Recessed Back Screen

Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2

2- 2

for a full screen compatibility chart for this mount. Begin with longer length screw, hand thread through multi-washer , adapter bracket (BB or CC) and spacer in that

order into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.

SCREEN

SP ACER

fig 2.2

MUL TI-WASHER

SCREW

ADAPTER BRACKET

(BB or CC)

If you have any questions, please call Peerless customer care at 1-800-865-2112.

8 of 27

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

ISSUED: 11-21-07 SHEET #: 202-9255-2 02-22-08

Mounting and Removing Flat Panel Screen

WARNING

• Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel screen.

• Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws to 40 in. • lb (4.5 N.M.) maximum torque.

• Be careful not to pinch fingers when pushing screen from the bottom.

T ension Adjustment of Ratchet Handle: Adjust tension in tilt brackets (BB & CC) by rotating ratchet

handle. NOTE: If obstruction prevents ratchet handle from rotating, pull handle out while turning will allow handle to reposition without tightening. Release and turn handle to tighten or loosen.

Mounting Screen: Ratchet handle must be in the up or down position or interference will occur while hooking tilt brackets to wall plate (AA). Slowly hook tilt brackets (BB & CC) onto wall plate (AA) and swing screen down as shown in fig. 3.1. Tilt bracket hooks must fully engage wall plate as shown in detail 1. Using phillips screw driver or security allen wrench (FF), turn safety/ security screws on tilt brackets (BB & CC) clockwise till screw tip securely contacts wall plate as shown in cross section.

SAFETY/

SECURITY

SCREW

DETAIL 1

RATCHET

HANDLE

fig 3.1

CROSS SECTION

Screen Adjustment: Screen can be adjusted

horizontally by loosening safety/security screws on tilt brackets (BB & CC) three full turns. Adjust screen as shown in figure 3.2. Tighten safety/security screws on tilt brackets till screw tip securely contacts wall plate as shown in cross section.

Removing Screen: T o remove screen from mount, loosen safety screws, swing screen away from mount, and lift screen off of mount.

Adjusting the Tilt Angle of the Flat Panel Screen

For preset tilt angles use Increlok™ and for custom tilt angle use ratchet handle.

INCRELOK™: The screen can be locked into a pre-set tilt position of -5°, 0°, 5°, 10° or 15°. Use locator hole to find tilt position hole and tilt screen to align holes. Tighten IncreLok™ tilt locking screws on both tilt brackets to lock tilt as shown in detail 2.

Ratchet Handle: Loosen ratchet handle (refer to step 3 for tension adjustment of handle). Push or pull from top or bottom of screen to adjust tilt as shown in figure

4.1. The tilt can be adjusted to a maximum of 15° forward or 5° backward.

IncreLok™

TIL T LOCKING

SCREW

TILT

POSITION

HOLES

fig 3.2

LOCATOR

HOLE

RATCHET

HANDLE

DETAIL 2

fig 4.1

9 of 27

Visit Peerless website at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870

All other brand and product names are trademarks or registered trademarks of their respective owners.

ISSUED: 11-21-07 SHEET #: 202-9255-2 02-22-08

+ 18 hidden pages