Peerless-AV SR1M Installation

Installation and Assembly:
Display Stand for 32" - 60" Flat Panel Displays
Models: SS560F
Max UL Load Capacity: 150 lb (68 kg)
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com
ISSUED: 08-05-11 SHEET #: 009-9054-4 07-25-12
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, and fully understands these instructions.
• Never exceed the Maximum UL Load Capacity on page 1.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.
• The stand is not affi xed or secured to the fl oor, and may therefore tip over and/or fall if display and/or stand is shaken or hit. Always monitor children and do not let children play alone around stand as they could get hurt by a falling display. Not recommended for use in areas with heavy traffi c.
Tools Needed for Assembly
• level
• phillips screwdriver
Table of Contents
Assembling Floor Stand .........................................................................................................................................................4
Attaching Display using VESA 100, 200 or VESA 300 Mounting Pattern ...............................................................................6
Mounting Flat Panel Display ..................................................................................................................................................8
2 of 9
ISSUED: 08-05-11 SHEET #: 009-9054-4 07-25-12
SS560F
Description Qty. Part #
A
base 1 009-1407
B upright 1 009-1413 C display mounting bracket 1 201-1156 D adapter plate 1 009-1599 E top cover 1 590-1210 F 3/8-16 x 2.5" button socket cap screw 3 520-9550
G 1/4-20mm nut 6 530-1050
H 1/4-20 x 12mm decorative screw 10 520-2325
I 4mm allen wrench 1 560-9646
J 7/32" allen wrench 1 560-9715
K M10 x .402 ID washe
r
3 540-9424
Parts List
Before you begin, make sure all parts shown are included with your product.
A
B
Some parts may appear slightly different than illustrated.
G
H
IJ
Adapter Bracket Fasteners
E
K
C
D
F
M5 x 12 mm (4)
(520-1027)
M5 x 25 mm (4)
(520-9543)
M6 x 12 mm (4)
(520-1128)
M6 x 25 mm (4)
(520-1208)
M8 x 12 mm (4)
(520-9571)
3 of 9
M8 x 25 mm (4)
(520-1031)
ISSUED: 08-05-11 SHEET #: 009-9054-4 07-25-12
.75" spacer (4)
(540-1059)
Multi-washer (4)
(580-1398)
Attach upright (B) to base (A) with three 3/8-16 x 2.5" socket screws (F) and three M10 washers (K) as shown in
1
gure 1.1. Tighten screws using 7/32" allen wrench (J). Run cords through upright (B) using cord management holes as shown in fi gure 1.2.
CORD
MANAGEMENT HOLE
B
A
B
CORD
MANAGEMENT HOLE
g. 1.1
Loosely attach six 1/4-20 x 12 mm screws (H) and
2
1/4-20 nuts (G) to display mounting bracket (C).
F
K
G
g. 1.2
Slide display mounting bracket (C) onto upright (B)
3
so that 1/4-20 nuts (G) slide into slots of upright (B) as shown in fi gure 3.1 and detail 1. Slide display mounting bracket to desired position, level, then tighten 1/4-20 x 12 mm screws (H) using 4 mm allen wrench (I).
g. 3.1
C
G
H
B
H
C
4 of 9
DETAIL 1
SLOT
B
ISSUED: 08-05-11 SHEET #: 009-9054-4 07-25-12
Snap top cover (E) onto upright (B).
4
E
B
Insert two 1/4-20 x 12 mm screws (H) into display mounting bracket (C), leaving 1/8" of exposed thread as shown
5
in fi gure 5.1 and detail 2.
g. 5.1
H
1/8"
C
DETAIL 2
5 of 9
ISSUED: 08-05-11 SHEET #: 009-9054-4 07-25-12
Installing Adapter Plate
WARNING
• Tighten screws so adapter plate is fi rmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and adapter plate is still not tightly secured, damage may occur to display or product may fail.
To prevent scratching the display, set a cloth on a fl at, level surface that will support the weight of the display. Place
6
display face side down. If display has knobs on the back, remove them to allow the adapter plates to be attached. Place adapter plate (D) on back of display, align to holes, and center on back of display as shown below. Attach the adapter plates to the back of the display using the appropriate combination of screws, multi-washers, and spacers as shown in fi gure 6.1 or 6.2.
NOTE: Top and bottom mounting holes on display must be used for attaching brackets. NOTE: Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.
X
D
X
NOTE: "X" dimensions should be equal.
MULTI-WASHER
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
NOTE: For fl at back displays proceed to step 6-1. For bump-out or recessed back display skip to step 6-2.
NOTES:
• The number of fasteners used will vary, depending upon the type of display.
• Multi-washers and spacers may not be used, depending upon the type of display.
• Use the corresponding hole in the multi-washer that matches your screw size as shown.
6 of 9
ISSUED: 08-05-11 SHEET #: 009-9054-4 07-25-12
Attaching Display using VESA 100, 200 or VESA 300 Mounting Pattern
WARNING
• If screws don't get three complete turns in the display inserts or if screws bottom out and adapter plate is still not tightly secured, damage may occur to display or product may fail.
For Flat Back Display
Select the screws from the baffl ed fastener pack that best fi t your display. Begin with the shortest length screw,
6-1
hand thread through multi-washer and three full turns into the mounting hole and fi t snug into place. Do not overtighten. If screw cannot make three full turns into the display, select a longer length screw from the baffl ed fastener pack. Repeat for remaining mounting holes and tighten screws.
NOTE: Spacers may not be used, depending upon the type of display.
adapter plate (D) into display as shown below. Screw must make at least
DISPLAY
If you have any questions, please call Peerless customer care at 1-800-865-2112.
For Bump-out or Recessed Back Display
6-2
Select the screws from the baffl ed fastener pack that best fi t your display. Begin with longer length screw, hand thread through multi-washer, adapter plate (D) and spacer in that order into display as shown below. Screw must make at least three full turns into the mounting hole and fi t snug into place. Do not overtighten. If screw cannot make three full turns into the display, select a longer length screw from the baffl ed fastener pack. Repeat for remaining mounting holes and tighten screws.
g. 6.1
MULTI-WASHER
SCREW
D
DISPLAY
SPACER
MULTI-WASHER
SCREW
D
If you have any questions, please call Peerless customer care at 1-800-865-2112.
g. 6.2
7 of 9
ISSUED: 08-05-11 SHEET #: 009-9054-4 07-25-12
Attach adapter plate (D) to display mounting
7
bracket (C).
D
C
Insert two 1/4-20 x 12 mm screws (H) into holes indicated below for desired display orientation. Tighten all screws
8
using 4 mm allen wrench (I).
H
H
No Tilt
2° Backward Tilt
5° Forward Tilt
H
8 of 9
All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 08-05-11 SHEET #: 009-9054-4 07-25-12
© 2011, Peerless Industries, Inc. All rights reserved.
LIMITED FIVE-YEAR WARRANTY
Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and workmanship, under normal
use, for a period of fi ve years from the date of purchase by the original end-user (but in no case longer than six years after the date of the product’s manufacture).
In no event shall the duration of any implied warranty of merchantability or fi tness for a particular purpose be longer than the period of the applicable
express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless,
(b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings when installing,
In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured
by a security device which may be included with the Peerless® product. Some states do not allow the exclusion or limitation of incidental or consequential
This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other
person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product.
At its option, Peerless will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third party actions and force majeure.
damages, so the above limitation or exclusion may not apply to you.
This warranty gives specifi c legal rights, and you may also have other rights which vary from state to state.
www.peerlessmounts.com
© 2011 Peerless Industries, Inc.
9 of 9
ISSUED: 08-05-11 SHEET #: 009-9054-4 07-25-12
Loading...