Peerless Industries SP 850P, SP 850, SP 850-S, SP 850P-S User Manual
Installation and Assembly:
Flat Panel Pull-out Swiv el W all Mount f or 26" - 58"
Screens
Models: SP 850, SP 850P, SP 850-S, SP 850P-S
This product is intended for use with UL
R
Max Load Capacity: 150 lb (68 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
Listed products and must be installed by a
qualified professional installer.
Note: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer care at 1-800-729-0307.
• This product should only be installed by a qualified professional.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum UL Load Capacity of 150 lb (68 kg).
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edge to edge" stud finder is highly recommended.
• Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely
handle placement of the screen.
• Tighten screws firmly , but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product was designed and intended to be mounted to the following supporting surfaces checked below with the
hardware included in this product as specified in the installation sheet. To mount this product to an alternative supporting surface, contact Peerless customer care at 1 800 865-21 12.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED
x Wood Stud None
x Wood Beam None
x Solid Concrete None
x Cinder Block None
Metal Stud Do not attach except with Peerless accessory kit for metal studs;
Contact Customer Service for Peerless accessory kit for metal studs.
Brick Contact Customer Service
Other or unsure? Contact Customer Service
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended) • 3/8" socket wrench (3/8" extended driver is recommended)
• phillips screwdriver • drill • 1/4" bit for concrete and cinder block wall • 5/32" bit for wood stud wall
• level • 6 mm allen wrench (if attaching to PLP models)
Table of Contents
Parts List..............................................................................................................................................................................3
Installation to Wood Stud Wall .............................................................................................................................................4
Installation to Solid Concrete and Cinder Block ....................................................................................................................5
Mounting Flat Panel Screen with VESA hole pattern .........................................................................................................6,7
Mounting Flat Panel Screen with Peerless PLP model adapter plate (PLP adapter plates are not UL listed) .......................7
Screen Compatibility Chart .................................................................................................................................................10
For customer care call (800) 729-0307 or (708) 865-8870.
2 of 10
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
Parts List
De scri ption Qty. Part # Part # Part # Part #
wall mount assem bl y 1 201-0385 201-0386 201-0383 201-0384
A
loc k i ng t ab 1 200-1871 200-1871 200-4871 200-4871
B
.219 ID x . 5 OD x . 125H s pacer 1 540-1032 540-1032 540-1032 540-1032
C
#14 x 2. 5" hex head wood sc rew 4 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03
D
All i gat or® anchor 4 590-0097 590-0097 590-0097 590-0097
E
18" polyester mesh sleeve 2 600-1014 600-1014 600-1014 600-1014
F
cabl e t ie 4 560-9711 560-9711 560-9711 560-9711
G
M10 x 15 mm socket head s crew 4 520-9262 520-9262 520-9262 520-9262
K
.198 x .313 x . 437H retai ning spacer 4 590-5005 590-5005 590-5005 590-5005
L
4 mm securit y allen wrenc h 1 560-1146 n/a 560-1146 n/a
M
M5 x 10 mm screw 5 520-1063 520-1233 520-1063 520-1233
AA
M4 x 12 mm screw 4 510-1079 504-9013 510-1079 504-9013
BB
M4 x 20 mm screw 4 510-1061 504-9020 510-1061 504-9020
CC
M5 x 40 mm screw 1 510-1001 520-1199 510-1001 520-1199
DD
Some parts may appear slightly different than illustrated.
A
K
SP850 SP850P SP850-S SP850P-S
Security Phillips Security Phillips
(not shown) (not shown)
G
L
BB
M
B
E
C
Snap installation tab off of wall mount assembly (A).
1
A
CC
DD
AA
D
F
INSTALLATION TAB
3 of 10
ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07
Loading...