Peerless-Premier PLP UN-1 User Manual

Installation and Assembly -
Solid•Point™ Universal Adapter bracket for Large Flat Panel Screens
PARTS LIST
Parts List
AA 200-0333 1 adapter bracket BB 200-1302 2 vertical bracket CC 520-1151 4 10-32 x 3/8" serrated head socket pin screw DD 540-9440 6 1/4" washer EE 520-1050 6 M6 x 1 x 12 mm socket pin screw FF 520-1064 8 M5 x .8 x 12 mm socket pin screw GG 520-1156 8 M4 x .7 x 10 mm serrated socket pin screw HH 520-1068 6 M8 x 1.25 x 15mm socket pin screw II 520-1101 4 M8 x 25 mm socket pin screw JJ 540-9400 8 #10 washer KK 540-1015 4 1/2" spacer LL 560-9646 1 security allen wrench MM 520-1152 4 M8 x 40 mm socket pin screw
Some parts may appear slightly different than illustrated.
AA
KK
II
HH
EE
FF
GG
JJ
LL
Model: PLP UN-1
BB
CC
DD
MM
For easier reference during assembly all fasteners on this page are scaled 1:1
T o assemble the adapter bracket (AA) to your flat screen product, please refer to the compatibility chart and configurations table on accompanying screen compatibility chart. First, locate your flat screen product in the compatibility chart using the manufacturers name and model number. Next, note the configuration letter shown in the far right hand column. Finally, use the configurations table, which appears after the compatibility chart, to determine the correct mounting hardware for your flat screen product.
1 of 4
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
ISSUED: 09-09-02 SHEET #: 200-9432-12 07-14-05
Slide vertical brackets (BB) onto c-channels as shown below. Refer to the t able on the last page of the screen
1
compatibility chart to determine the proper assembly of the vertical bracket (BB). For standard bracket mounting, see figure 3. For reverse bracket mounting, see figure 4.
Example: For a Toshiba model 50 HP82 50" screen, assemble the vertical bracket (BB) as shown in figure 4 below
(reverse bracket mounting).
BB
c-channel
AA
BB
fig. 3 Bracket Mounting: Standard
c-channel
AA
fig. 4 Bracket Mounting: Reverse
2 of 4
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
ISSUED: 09-09-02 SHEET #: 200-9432-12 07-14-05
Set a cloth on the floor to prevent scratching the screen. Place the screen on the floor face down. If the screen has
2
knobs on the back, remove them. Place adapter bracket (AA) on the center of the screen. Slide the vertical brackets (BB) along the c-channels of the adapter bracket (AA) until the slots on the back of the vertical brackets (BB) are aligned to the holes on the back of the screen. Fasten vertical brackets (BB) to c-channels using four 10-32 x 3/8" serrated head socket pin screws (CC).
Note: Do not fully tighten the screws (CC) to allow the adapter bracket to slide along the vertical brackets (BB) freely .
BB
c-channel
CC
BB
3 of 4
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
ISSUED: 09-09-02 SHEET #: 200-9432-12 07-14-05
Slide the vertical brackets (BB) along the c-channels of the adapter bracket (AA) until the slots on the back of the
3
vertical brackets (BB) are aligned to the holes on the back of screen. Fully tighten the four 10-32 x 3/8" serrated head socket pin screws (CC) which hold the vertical brackets (BB) to the c-channels. Refer to the accompanying screen compatibility chart to determine the proper fasteners to use. Attach the assembled adapter bracket to the back of the screen using screws, upper and lower spacers as pictured. V erify that all holes are properly aligned, then use the security allen wrench (LL) to tighten the screws.
Note: See figure 5 below for slot sizes. Example: For a Toshiba model 50 HP82 50" screen, attach the vertical brackets (BB) to the screen using eight
M4 x 10 mm serrated socket pin screws (GG) or M5 x 12 mm socket pin screws (FF) through the small slots on the vertical brackets (BB). Please refer to the corresponding configuration note for more details. Upper spacers (JJ) are required for this configuration.
BB
SCREWS
UPPER SPACERS
LOWER SPACERS
C-CHANNNEL
AA
fig. 5 Mounting Slots
SMALL SLOTS ARE USED FOR M4 AND M5 SCREWS.
LARGE SLOTS ARE USED FOR M6 AND M8 SCREWS.
MOUNTING SLOTS: SMALL
MOUNTING SLOTS: LARGE
4 of 4
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
© 2004 Peerless Industries, Inc. All rights reserved. Peerless is a registered trademark and Solid•Point is a trademark of Peerless Industries, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 09-09-02 SHEET #: 200-9432-12 07-14-05
Loading...