Peerless-AV DSX200 Installation

Page 1
Installation and Assembly:
A
Shelf Bracket for Media Device
Model: DSX200
Parts List
Description Qty. Part #
shelf 1 124-1941 right vertical support 1 124-1944
B
left vertical support 1 124-1943
C
adjustment bracket 2 124-1945
D
M5 x 16 phillips screw 8 520-1189
E
M5 x 25 mm phillips screw 2 520-9543
F
1/4-20 x 1/2 round phillips screw 4 510-9108
G
safety belt 1 170-8039-1
H
C D
E F
G
Secure two adjustment brackets (D) to shelf (A) using four 1/4-20 x 1/2 round phillips screws (G).
1
USE BACK MOUNTING HOLES
USE BACK MOUNTING HOLES
G
G
High Shelf Position
1 of 5
Low Shelf Position
ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10
Page 2
Attaching to Wall Plate
Hook right and left vertical supports (B and C) onto wall plate (not supplied) and secure using two
2
M5 x 25 mm phillips screws (F). NOTE: Don’t fully tighten M5 x 25 mm phillips screws (F) until after Step 3
Wall Plate
(Not supplied)
F
Secure adjustment brackets (D) to right and left vertical supports (B and C) using eight M5 x 16 mm phillips screws (E).
3
Position right and left vertical supports (B and C) in desired location then tighten M5 x 25 mm phillips screws (F).
Wall Plate
(Not supplied)
E
F
F
Wall Plate
(Not supplied)
E
High Shelf Position
2 of 5
Low Shelf Position
ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10
Page 3
Attaching Safety Belt
Select slot in tray as shown in g 4.1.
4
Remove backing and attach one clear strip through slot and around edge of tray as shown in g. 4.2.
Repeat for other slot on other side of tray.
NOTE: This material prevents fraying or cutting of the belt.
Fig. 4.1
FRONT LIP
Take one belt and hold it so that the tri-bar belt clip is facing as illustrated. Feed belt up through the slot you have chosen.
5
Remember, belt only goes through outside slot. Now feed belt through belt clip as shown.
Repeat on other side of tray using other belt.
SLOT
Fig. 4.2
CLEAR STRIPS
1
Continue by sliding on one belt guide and tri-bar clip on each side of the buckle. Refer to drawing below.
TRI-BAR BELT CLIP
2
6
TOP
BOTTOM
NOTE: Teeth face down
3 of 5
ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10
3
Page 4
Pull end of safety belt (H) out of bottom buckle slot and back down through top buckle slot. NOTE: Do not tighten safety belt (H).
Bottom buckle slot
4
BELT GUIDE
NOTE: To attach screen to wall plate, spacers may be needed. Refer to wall mount instructions for use of spacers.
Tighten safety belt (H) by pulling on loose end of safety belt.
6
5
BELT GUIDE
Top buckle slot
4 of 5
ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10
Page 5
Make sure that attachment brackets (not included) are at
7
desired tilt before installing to wall plate (not included). Measure display hole pattern before securing display to wall plate (not included).
Large Mounting Hole Pattern
Vertical brackets Outside
If display mounting pattern is larger than distance between vertical supports of shelf mount brackets, position attachment brackets on outside with ratchet handles facing outward as shown in Fig 7.1.
RATCHET HANDLE
ATTACHMENT BRACKETS
Fig. 7.1
VERTICAL BRACKETS
Small Mounting Hole Pattern
Vertical brackets inside
If display mounting holes are smaller than distance between vertical supports of shelf mount brackets, position attachment brackets on inside with ratchet handles facing inward as shown in Fig 7.2.
RATCHET HANDLE
ATTACHMENT BRACKETS
VERTICAL BRACKETS
18.65"
Fig. 7.2
18.65"
Same Mounting Hole Pattern
Vertical brackets inside and Outside
NOTE: Shelf will be offset to the right or left in this orientation.
If display mounting holes are equal to distance between vertical supports of shelf mount brackets, position attachment brackets on right or left side of shelf mount brackets with ratchet handles facing outward as shown in Fig 7.3. NOTE: Vertical brackets can be mounted on right or left side of shelf as shown in light gray.
RATCHET HANDLE
ATTACHMENT BRACKETS
VERTICAL BRACKETS
5 of 5
Fig. 7.3
ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10
© 2010, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or
registered trademarks of their respective owners.
Loading...