DS-VWM770
46" - 70"
(1168 - 1778 cm)
MAX
125 lb
(56 kg)
ENG
1
2013-08-27 #:125-9465-3 2013-10-11
ENG
This page intentionally left blank.
2
2013-08-27 #:125-9465-3 2013-10-11
WARNING
ENG - This product is designed to be installed on wood stud, solid concrete or cinder block walls. Hardware is
included for wood stud, solid concrete and cinder block installation. Before installing make sure the supporting
surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do
not overtighten screws or damage can occur and product may fail. Never exceed the Maximum Load Capacity.
Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This product is
intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury. Be
careful not to pinch ngers when operating the mount. For support please call customer care at 1-800-865-2112.
ENG
Symbols
ENG
WARNING
x3
Screws must get at least three
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
full turns and t snug.
ENG
1
#
ENG
Skip to step.
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
5/32"
(4mm)
3/8"
(10mm)
5/16"
(8mm)
2
3
+1/2
4
3
2013-08-27 #:125-9465-3 2013-10-11
ENG
Parts (Before beginning, make sure you have all parts shown below).
Parts List
Part Description Qty. Part #
A
wall plate 1 201-0387
B
concrete anchor 4 590-0320
C
wood screw 4 5S1-015-C03
D
locking tab 1 200-1871
E
.219" spacer 1 540-1032
F
polyester sleeve 2 600-1014
G
cable tie 4 560-9711
H
M5 x 10mm screw 5 520-1063
I
M4 x 12mm screw 4 510-1079
J
M5 x 40mm screw 1 510-1001
K
4mm allen wrench 1 560-9646
L
adapter bracket 2 145-1779
M
plate assembly 1 145-1784
N
M10 x 15mm 4 520-9262
O
M5 x 8mm 4 520-1167
P
M6 x 12mm 4 520-1050
Q
shoulder washer 4 590-2233
R
M8 x 15mm 4 520-1068
(1)
A
wall plate
D (1)
locking tab
E (1)
.219" spacer
(4)
B
concrete anchor
(4)
C
wood screw
F (2)
polyester sleeve
4
2013-08-27 #:125-9465-3 2013-10-11
G (4)
cable tie
4mm allen wrench
K (1)
H (5)
M5 x 10mm
I (4)
M4 x 12mm
J (1)
M5 x 40mm
L (2)
adapter bracket
Q (4)
shoulder washer
R (4)
M8 x 15mm
M (1)
plate assembly
N (4)
M10 x 15mm
O (4)
M5 x 8mm
P (4)
M6 x 12mm
5
2013-08-27 #:125-9465-3 2013-10-11
1
2
ENG
Remove
ENG
A
Wood stud wall.
ENG
Concrete/Cinder block.
2a
2a
WARNING
ENG - When installing Peerless wall mounts on a
wood stud wall covered with gypsum board (drywall),
verify that the woods studs are a minimum of 2" x 4"
nominal size. When installing to more than one stud,
ensure the spacing between studs is at least 16"
but does not exceed 24". Do not install over gypsum
board thicker than 5/8".
2a-2
2a-1
2b
ENG
Use stud nder to locate
and mark stud center lines.
ENG
ENG
Level wallplate.
Mark mounting holes on stud centerlines.
A
6
2013-08-27 #:125-9465-3 2013-10-11
2a-3
2.5"
(64mm)
5/32"
(4mm)
ENG
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
2a-4
Level wallplate. Install using wood screws provided.
ENG
C (4)
5/32"
(4mm)
ENG
Mounting hole must center on stud.
A
Maximum 80 in. • lb (9 N.M.).
ENG
3
7
2013-08-27 #:125-9465-3 2013-10-11
2b
WARNING
ENG • When installing Peerless wall mounts on a concrete wall, the wall must be at least 8" thick with a minimum
compressive strength of 2000 psi.
• When installing Peerless wall mounts on a cinder block wall, the cinder blocks must meet ASTM C-90
specications and have a minimum nominal width of 8". Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" (25 mm) minimum from the side of the block. It is suggested that a standard electric
drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole
when entering a void or cavity.
• Never attach expansion anchors to concrete or cinder block covered with plaster, drywall or other nishing
material.
2b-1
ENG
Level wallplate. Mark mounting holes.
2b-2
5/16"
(8mm)
ENG
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
A
ENG
Do not drill into mortar joints.
5/16"
(8mm)
2.5"
(64mm)
8
2013-08-27 #:125-9465-3 2013-10-11
2b-32b-3
B (4)
1b-42b-4
Insert anchor ush to concrete.
ENG
B
Level wallplate. Install using concrete
ENG
anchors and wood screws provided.
ENG
Maximum 80 in. • lb (9 N.M.).
A
C (4)
9
2013-08-27 #:125-9465-3 2013-10-11
3
A
10
2013-08-27 #:125-9465-3 2013-10-11
4
ENG
Setting the angle of the display.
4-1
ENG
The viewport is used to reveal notches indicating the view of the display.
Rotating Plate
ENG
ENG
Notch
ENG
Viewport
4-2
ENG
Line up the viewpor t with the desired view.
ENG
Viewport
Rotating Plate
ENG
ENG
Rotation Guide
Each notch rotates display
clo ck wise 15°
ENG
Landscape
Each notch rotates display
counter-clockwise 15°
EACH MARK
ROTATES TV
CLOCKWISE
EACH MARK ROTATES TV
COUNTER-CLOCKWISE
M
M
ENG
Portrait
90°
90°
75°
60°
45°
30°
15°
0°
-15°
-30°
-45°
-60°
-75°
90°
-90°
11
ENG
Portrait
2013-08-27 #:125-9465-3 2013-10-11
5
Leaving ¼", thread two M10 x 15mm (N) screws through plate assembly (M) and rotating plate.
ENG
ENG
M
N
6
ENG
Slide plate assembly (M) into adapter bracket (L) slots.
L
M
Rotating Plate
12
2013-08-27 #:125-9465-3 2013-10-11
6-1
Determine VESA mounting pattern.
ENG
300mm x 300mm
400mm x 400mm
400mm x 300mm
400mm x 200mm
500mm x 400mm
600mm x 400mm
13
2013-08-27 #:125-9465-3 2013-10-11
6-2
L
Q
P, R
6-3
ENG
Secure plate assembly (M) to adapter bracket (L) with four M5 x 8mm screws (O).
L
M
O
ENG
Do not use screws on inner adapter bracket
opening.
14
2013-08-27 #:125-9465-3 2013-10-11
7
ENG
Slide M10 x 15mm screws (N) of plate assembly (M) into top two key holes of wall plate (A).
A
7-1
8
N
A
M
N
M
F
G
15
2013-08-27 #:125-9465-3 2013-10-11
9
ENG
Display adjustment.
9-1
9-2
9-3
16
2013-08-27 #:125-9465-3 2013-10-11
10
ENG
Use legend below to determine position of display.
NOTE: Each knob can be adjusted independently for ne tuning adjustments.
Turn knob CLOCKWISE to move corner toward the wall.
Turn knob COUNTER-CLOCKWISE to move c orner away from the wall.
17
2013-08-27 #:125-9465-3 2013-10-11
11
ENG
OPTIONAL: Alternative wall plate (A) lock-down positions.
11-1
ENG
Wall plate (A) lock-down in retracted position.
A
11-2
ENG
Wall plate (A) lock-down one arm in place.
A
J (1)
H (1)
D (1)
E (1)
18
2013-08-27 #:125-9465-3 2013-10-11
Peerless Industries, Inc. (“Peerless”) warrants to original end-users of Peerless® products will be free from defects in material and
LIMITED FIVE-YEAR WARRANTY
workmanship, under normal use, for a period of ve years from the date of purchase by the original end-user (but in no case longer than
six years after the date of the product's manufacture). At its option, Peerless will repair or replace, or refund the purchase price of, any
product which fails to conform with this warranty.
In no event shall the duration of any implied warranty of merchantability or tness for a particular purpose be longer than the
period of the applicable express warranty set forth above. Some states do not allow limitations on how long a implied warranty lasts,
so the above limitation may not apply to you.
This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service
or repairs by Peerless, (b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow
Peerless' instructions or warnings when installing, using or storing the product, or (d) misuse or accident, in transit or otherwise, including
in cases of third party actions and force majeure.
In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product,
whether or not secured by a security device which may be included with the Peerless
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No dealer,
distributor, installer or other person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless in
connection with the sale of any Peerless
This warranty gives specic legal rights, and you may also have other rights which vary from state to state.
®
product.
Patented. Utility Patent No. 8,517,322
®
product. Some states do not allow the
19
2013-08-27 #:125-9465-3 2013-10-11
Peerless-AV
2300 White Oak Circle
Aurora, IL 60502
Email: tech@peerlessmounts.com
Ph: (800) 865-2112
Fax: (800) 359-6500
www.peerless-av.com
© 2013, Peerless Industries, Inc.
20
2013-08-27 #:125-9465-3 2013-10-11
Loading...