DS-LEDIF Series
For Samsung IF015H, IF020H, IF025H
ENG
*Actual conguration may vary
1
2018-03-14 #:146-9020-4 (2019-05-16)
WARNING
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.
Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to
product failure or personal injury. Be careful not to pinch ngers when operating the mount. For support please
call customer care at 1-800-865-2112.
ENG
ENG
Symbols
Tools Needed for Assembly.
#
ENG
WARNING
ENG
Do not overtighten screws.
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
ENG
Skip to step.
1
2
3
+1/2
5/32"
(4mm)
3/8"
(10mm)
4
2
2018-03-14 #:146-9020-4 (2019-05-16)
ENG
This page intentionally left blank.
3
2018-03-14 #:146-9020-4 (2019-05-16)
ENG
Parts (Before beginning, make sure you have all parts shown below).
Parts List
Description
A left column
B right column
C inside vertical column
D top horizontal asy
E bottom horizontal asy
F top vertical spacer
G horizontal spacer
H M5 x 8mm socket screw
I #14 x 2.5" wood screw
J M5 square nut (spare)
K 3mm allen wrench two-tip T-handle
L wall plate shim
M connector plate
N M5 x 5mm set screw
O bottom vertical spacer
A
left column
B
right column
ENG
Refer to parts list included for your specic model.
C
inside vertical column
top horizontal assembly
bottom horizontal assembly
D
E
4
2018-03-14 #:146-9020-4 (2019-05-16)
F
top vertical
spacer
O
bottom vertical
spacer
G
horizontal
spacer
H
M5 x 8mm
L
wall plate
shim
J
M5 square nut
M
connector
plate
#14 x 2.5" wood screw
I
3mm allen wrench
two-tip T-handle
M5 x 5mm
set screw
K
N
5
2018-03-14 #:146-9020-4 (2019-05-16)
1
ENG
Refer to layout drawing included for your
specic model.
6
2018-03-14 #:146-9020-4 (2019-05-16)
2-1
ENG
Optional: If connecting two top horizontal extrusions,
rst remove inner hook-on brackets.
D
M5 x 16mm
K
ENG
Remove and save hardware.
2-2
ENG
Use extrusion connectors to connect top horizontal
extrusions.
M (4)
D
D
K
N (8)
D
7
2018-03-14 #:146-9020-4 (2019-05-16)
2-3
ENG
Replace one hook-on bracket in between connected
extrusions.
D
H (2)
K
ENG
Use saved hardware.
2-4
ENG
Optional: If connecting two bottom horizontal
extrusions, rst remove inner hook-on brackets
E
ENG
Remove and save hardware.
D
K
E
8
2018-03-14 #:146-9020-4 (2019-05-16)
2-5
ENG
Use extrusion connectors to connect bottom
horizontal extrusions.
M (3)
E
2-6
ENG
Replace one hook-on bracket in between connected
extrusions.
K
N (6)
E
K
E
ENG
Use saved hardware.
H
E
9
2018-03-14 #:146-9020-4 (2019-05-16)
3
WARNING
ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood
studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood
may be covered by gypsum board (drywall) up to 5/8" thick.
3-1
ENG
Level top horizontal extrusion and mark
mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
2.24"
(57mm)
display tile
10
D
2018-03-14 #:146-9020-4 (2019-05-16)
3-2
ENG
Use a laser level to keep mounting holes
level.
11
2018-03-14 #:146-9020-4 (2019-05-16)
3-3
2.5"
(64mm)
5/32"
(4mm)
ENG
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
3-4
ENG
Level extrusion. Install using wood screws
provided.
I (6)
5/32"
(4mm)
3/8"
(10mm)
ENG
Maximum 80 in. • lb (9 N.M.).
12
D
2018-03-14 #:146-9020-4 (2019-05-16)
3-5
ENG
Secure vertical spacers to the wall ush with the
horizontal extrusion.
3/8"
(10mm)
F
ENG
Edges must be ush.
D
F
I
13
F
2018-03-14 #:146-9020-4 (2019-05-16)
3-6
ENG
Use third vertical spacer to align bottom
horizontal extrusion ush with vertical spacer,
then mark mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
F
ENG
Edges must be ush.
F
E
14
E
2018-03-14 #:146-9020-4 (2019-05-16)
3-7
2.5"
(64mm)
5/32"
(4mm)
ENG
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
3-8
ENG
Use third vertical spacer to align bottom
horizontal extrusion ush with vertical
spacer, then install using wood screws
provided.
5/32"
(4mm)
3/8"
(10mm)
I (6)
ENG
Maximum 80 in. • lb (9 N.M.).
15
E
2018-03-14 #:146-9020-4 (2019-05-16)
4
ENG
Refer to layout drawing included for your
specic model.
5
16
4-1
2018-03-14 #:146-9020-4 (2019-05-16)
4-1
ENG
For larger congurations only; Secure vertical spacer
to the wall ush with the horizontal extrusion.
3/8"
(10mm)
E
ENG
Edges must be ush.
E
O
I
O
17
I (2)
O
2018-03-14 #:146-9020-4 (2019-05-16)
4-2
ENG
Use third vertical spacer to align bottom
horizontal extrusion ush with vertical spacer,
then mark mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
O
ENG
Edges must be ush.
O
E
18
E
2018-03-14 #:146-9020-4 (2019-05-16)
4-3
2.5"
(64mm)
5/32"
(4mm)
ENG
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
4-4
ENG
Use third vertical spacer to align bottom
horizontal extrusion ush with vertical
spacer, then install using wood screws
provided.
5/32"
(4mm)
3/8"
(10mm)
I (6)
ENG
Maximum 80 in. • lb (9 N.M.).
19
2018-03-14 #:146-9020-4 (2019-05-16)
5
ENG
Remove vertical spacers.
3/8"
(10mm)
F (2)
O (2)
20
2018-03-14 #:146-9020-4 (2019-05-16)
6
ENG
Loosen, adjust, tighten.
K
A
B
C
1
2
3
21
2018-03-14 #:146-9020-4 (2019-05-16)
7-1
ENG
Hook on and secure outer vertical columns.
"L" and "R" markings designate left and right
column.
A
ENG
Tighten hardware.
K
H (8)
22
B
2018-03-14 #:146-9020-4 (2019-05-16)
7-2
ENG
Hook on and secure all inside vertical
columns.
ENG
Tighten hardware.
K
H (20)
23
C (5)
2018-03-14 #:146-9020-4 (2019-05-16)
8-1
ENG
Loosen hardware on vertical columns.
K
24
2018-03-14 #:146-9020-4 (2019-05-16)
8-2
ENG
Plumb and level outer columns, then tighten
hardware. Tighten hardware on four corner wall
plates
ENG
K
Tighten.
25
ENG
Tighten.
2018-03-14 #:146-9020-4 (2019-05-16)
8-3
ENG
Tie a string between top slots on outer
columns in order to level the depth of each
vertical column.
ENG
Loosen, adjust, tighten.
K
ENG
Optional leveling for bowed walls
ENG
Loosen.
ENG
Insert.
L
ENG
Tighten.
26
2018-03-14 #:146-9020-4 (2019-05-16)
8-4
ENG
Tie a string between bottom slots on outer columns
in order to level the depth of each vertical column.
K
ENG
Loosen, adjust, tighten.
ENG
Optional leveling for bowed walls
ENG
Loosen.
ENG
Insert.
L
ENG
Tighten.
27
2018-03-14 #:146-9020-4 (2019-05-16)
8-5
ENG
With the string still attached, level the height of
each column
K
ENG
Tighten or loosen to adjust height.
28
2018-03-14 #:146-9020-4 (2019-05-16)
8-6
ENG
Adjust inner columns to t horizontal spacers.
Tighten column hardware after spacing. Start
from the left column.
K
G
29
2018-03-14 #:146-9020-4 (2019-05-16)
8-7
ENG
Continue adjusting inner columns to t horizontal
spacers until all are level. Tighten column hardware
after spacing
K
G
30
2018-03-14 #:146-9020-4 (2019-05-16)
8-8
ENG
Remove all spacers.
31
2018-03-14 #:146-9020-4 (2019-05-16)
9-1
ENG
Level L brackets and mark mounting holes
on plywood (must be minimum Grade BC,
1/2" (13mm) thick.)
9-2
5/32"
(4mm)
ENG
Drill mounting holes into supporting surface
(2.5" (64mm) minimum depth required).
32
2.5"
(64mm)
5/32"
(4mm)
2018-03-14 #:146-9020-4 (2019-05-16)
9-3
ENG
Level L brackets. Install using wood
screws provided.
ENG
Maximum 80 in. • lb (9 N.M.).
I (12)
3/8"
(10mm)
33
2018-03-14 #:146-9020-4 (2019-05-16)
9-4
ENG
Tie a string between center slots on outer column
in order to level the depth of each vertical column.
K
34
2018-03-14 #:146-9020-4 (2019-05-16)
9-5
ENG
Adjust depth, then remove string.
K
ENG
Loosen, adjust, tighten.
35
2018-03-14 #:146-9020-4 (2019-05-16)
10-1
ENG
Attach display, tighten connecting hardware, and run
cables one at a time starting from the bottom left.
1
2
3
4
36
5
6
2018-03-14 #:146-9020-4 (2019-05-16)
10-2
13
14
7
8
15
9
16
10
17
18
11
12
37
2018-03-14 #:146-9020-4 (2019-05-16)
11
ENG
To remove, start from the top right.
6
5
4
3
2
1
38
7
2018-03-14 #:146-9020-4 (2019-05-16)
ENG
This page intentionally left blank.
39
2018-03-14 #:146-9020-4 (2019-05-16)
Peerless Industries, Inc. (“Peerless-AV”) warrants to original end-users that each Peerless-AV® mounting product will be free from defects
LIMITED FIVE-YEAR WARRANTY
in material and workmanship, under normal use, for the applicable warranty period (from date of the original installation of the product).
At its option, Peerless-AV will repair or replace, or refund the purchase price of, any product which fails to conform with this warranty.
Any implied warranty of merchantability or tness for a particular purpose shall be limited to the period of the
express warranty set forth below.
In no event shall Peerless-AV be liable for incidental or consequential damages, whether or not secured by a
security device which may be included with the product.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of incidental or consequential damages, so
the above limitation and/or the above exclusion may not apply to you.
This warranty does not cover damage caused by incorrect selection, installation or the failure to follow Peerless-AV instructions or
warnings when installing, using or storing the product.
This warranty gives specic legal rights, and you may also have other rights which vary from state to state. To make a warranty claim in
North America, contact Peerless-AV customer care at 1-800-865-2112. See complete global warranty information for regions outside North
America at www.peerless-av.com/en-uk/customer-care/warranties-returns.
Peerless-AV
2300 White Oak Circle
Aurora, IL 60502
Email: tech@peerlessmounts.com
Ph: (800) 865-2112
Fax: (800) 359-6500
www.peerless-av.com
© 2019, Peerless Industries, Inc.
Peerless-AV Europe
Unit 3 Watford Interchange,
Colonial Way, Watford, Herts,
WD24 4WP, United Kingdom
Customer Care
44 (0) 1923 200 100
www.peerless-av.com
© 2019, Peerless Industries, Inc.
Peerless-AV de Mexico
Ave de las Industrias 413
Parque Industrial Escobedo
Escobedo N.L Mexico 66062
Servicio al Cliente
01-800-849-65-77
www.peerless-av.com
© 2019, Peerless Industries, Inc.
Loading...