Peerless-AV DS-C560-1X3 Installation
DS-C560-1X3
46" - 60"
(117 - 152 cm)
MAX
500 lb
(227 kg)
ENG
1
2015-06-30 #:009-9119-3 (2016-05-16)
This page intentionally left blank.
2
2015-06-30 #:009-9119-3 (2016-05-16)
WARNING
Do not begin to install product until you have read and understood the instructions and warnings contained in
this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
This product must be installed onto fl at, hard, level surface to prevent tipping. The cart or stand is not affi xed or
secured to the fl oor, and may therefore tip over and/or fall if screen and/or stand is shaken or hit. Displays must
be removed before moving cart. Not recommended for use in areas with heavy traffi c. This product is intended
for indoor use only. Use of this product outdoors could lead to product failure or personal injury. Screws must
be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the
Maximum Load Capacity. Be careful not to pinch fi ngers when operating the mount. For support please call
customer care at 1-800-865-2112.
ENG
Symbols
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
ENG
WARNING
Screws must get at
ENG
least three full turns
and fi t snug.
x3
2
ENG
Heavy
Display center.
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
3
+1/2
4
(13mm)
3
2015-06-30 #:009-9119-3 (2016-05-16)
Parts (Before beginning, make sure you have all parts shown below).
Parts List
A caster, 5" swivel 4 600-0026
B caster support 4 145-T1799
C cover 6 145-T1809
D base support tube 2 145-T1812
E base support 8 560-T1261
F left adaptor bracket 3 146-1609
G right adaptor bracket 3 146-1608
H base leg 2 145-T1767
I horizontal leg support 1 146-T1340
J vertical leg support 2 145-T1777
K extension 2 145-T1778
L vertical support bracket 6 145-T1806
M cross support 3 145-T1816
N computer cover 1 145-T1930
O computer shelf 1 145-T1931
P extension adaptor 2 145-T1935
Q cord bracket 4 146-T1321
R knurled knob 4 560-1160
S M8 x 16mm socket button screw 120 520-9527
T M8 square nut 40 530-1066
U cover clip 24 590-0317
V M5 x 10mm type-f, socket pin screw 8 520-1164
W bar nut 20 146-1319
X nylon shoulder washer 12 590-2233
Y M6 x 12mm socket pin screw 12 520-1050
Z 1/4" power bit 1 560-0263
AA 5mm allen wrench 1 560-9640
BB 4mm allen wrench 1 560-9646
A
(4)
caster
(4)
B
caster support
C
(6)
cover
(2)
D
base support
tube
(8)
E
base support
Part #Description Qty
(3)
F
left adaptor
bracket
(3)
G
right adaptor
bracket
(2)
J
vertical leg
support
(2)
H
base leg
K
extension
(2)
(1)
I
horizontal leg
support
4
(6)
L
vertical support
bracket
2015-06-30 #:009-9119-3 (2016-05-16)
Q
cord
bracket
(4)
(3)
M
cross support
R
knurled
knob
(4)
(1)
N
computer cover
(
120
S
M8 x 16mm
(1)
O
computer shelf
)
(40)
T
M8 square nut
P
extension
adaptor
(24)
U
cover clip
(2)
(8)
V
M5 x 10mm
W
(20)
bar nut
AA
5mm allen
wrench
(1)
(12)
X
nylon shoulder
washer
5
(12)
Y
M6 x 12mm
(1)
BB
4mm allen
wrench
2015-06-30 #:009-9119-3 (2016-05-16)
(1)
Z
1/4" power
bit
1-1
B
x4
S (4)
1-2
AA
A
(5mm)
Do not fully tighten hardware
x4
S (2)
T (2)
SIDE VIEW
6
2015-06-30 #:009-9119-3 (2016-05-16)
2
x2
S (4)
D
AA
(5mm)
T (2)
H
T (2)
T (2)
T (2)
7
D
S (4)
2015-06-30 #:009-9119-3 (2016-05-16)
3
x3
TIGHTEN
CONNECTING
HARDWARE
ENG
FLUSH
EDGES
Casters must be fl ush to end of horizontal leg support.
ENG
4
x8
S (4)
W (2)
E
SIDE VIEW
Do not fully tighten hardware
8
2015-06-30 #:009-9119-3 (2016-05-16)
Loading...