Peerless-AV DS-C555-3X2 Installation
DS-C555-3X2
46" - 55"
(117 - 140 cm)
MAX
600 lb
(272 kg)
ENG
1
2014-05-30 #:009-9084-6 (2016-04-20)
This page intentionally left blank.
2
2014-05-30 #:009-9084-6 (2016-04-20)
WARNING
Do not begin to install product until you have read and understood the instructions and warnings contained in
this user guide. Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
This product must be installed onto fl at, hard, level surface to prevent tipping. The cart or stand is not affi xed or
secured to the fl oor, and may therefore tip over and/or fall if screen and/or stand is shaken or hit. Displays must
be removed before moving cart. Not recommended for use in areas with heavy traffi c. This product is intended
for indoor use only. Use of this product outdoors could lead to product failure or personal injury. Screws must
be tightly secured. Do not overtighten screws or damage can occur and product may fail. Never exceed the
Maximum Load Capacity. Be careful not to pinch fi ngers when operating the mount. For support please call
customer care at 1-800-865-2112.
ENG
Symbols
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
ENG
WARNING
Screws must get at
ENG
least three full turns
and fi t snug.
x3
2
ENG
Heavy
Display center.
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
3
+1/2
4
(13mm)
3
2014-05-30 #:009-9084-6 (2016-04-20)
Parts (Before beginning, make sure you have all parts shown below).
Parts List
A caster, 5" swivel 4 600-0026
B caster support 4 145-T1799
C cover 6 145-T1809
D base leg 2 145-T1767
E horizontal leg support 1 145-T1785
F base support tube 2 145-T1812
G base support 8 560-T1261
H vertical leg support 2 145-T1777
I left adaptor bracket 6 145-T1609
J right adaptor bracket 6 145-T1608
K side support bracket 2 145-T1807
L vertical support bracket 4 145-T1806
M computer cover 1 145-T1930
N computer shelf 1 145-T1931
O dual cross support 2 145-T1924
P cord bracket 4 146-T1321
Q knurled knob 4 560-1160
R cross support 2 145-T1816
S plate connections 4 145-T1821
T M8 x 16mm socket button screw 128 520-9527
U M8 square nut 44 530-1066
V cover clip 24 590-0317
W M5 x 10mm type-f, socket pin screw 14 520-1164
X 1/4" power bit 1 560-0263
Y 5mm allen wrench 1 560-9640
Z bar nut 16 146-1319
AA nylon shoulder washer 24 590-2233
BB M6 x 12mm socket pin screw 24 520-1050
CC 4mm allen wrench 1 560-9646
A
(4)
caster
(4)
B
caster support
C
(6)
cover
(2)
F
base support
tube
(8)
G
base support
(6)
I
left adaptor
bracket
Part #Description Qty
J
right adaptor
bracket
(6)
D
base leg
(2)
H
vertical leg
support
(2)
(1)
E
horizontal leg
support
L
vertical support
bracket
4
(2)
K
side support
bracket
(4)
2014-05-30 #:009-9084-6 (2016-04-20)
(2)
O
dual cross
support
(1)
M
computer cover
(1)
N
computer shelf
(24)
V
cover clip
(2)
R
cross support
W
M5 x 10mm
(14)
connections
(1)
X
1/4" power bit
S
(4)
plate
(
128
T
M8 x 16mm
(1)
Y
5mm allen
wrench
P
cord
bracket
(4)
)
(4)
Q
knurled
knob
(44)
U
M8 square nut
(16)
Z
bar nut
AA (24)
nylon shoulder
washer
BB (24)
M6 x 12mm
CC (1)
4mm allen
wrench
5
2014-05-30 #:009-9084-6 (2016-04-20)
1
x4
T (4)
(5mm)
Y
B
A
Do not fully tighten hardware
T (2)
U (2)
SIDE VIEW
6
2014-05-30 #:009-9084-6 (2016-04-20)
2
x2
T (4)
F
Y
(5mm)
U (2)
D
U (2)
U (2)
U (2)
T (4)
7
F
2014-05-30 #:009-9084-6 (2016-04-20)
3
Repeat for each base leg assembly.
TIGHTEN
CONNECTING
HARDWARE
ENG
FLUSH
EDGES
Casters must be fl ush to end of horizontal leg support.
ENG
4
T (4)
Z (2)
x8
G
SIDE VIEW
Do not fully tighten hardware
8
2014-05-30 #:009-9084-6 (2016-04-20)
Loading...