How it Works
Pedigo
Loading...
P-2030

Pedigo P-2010, P-2020, P-2055, P-2030, P-2040 Operation & Care Instructions Manual

...
Download
OPERATION & CARE
MANUAL FOR
P-2010
P-2020
P-2030
P-2040
P-2050
P-2055
LANKET
B
WARMING
CABINETS
BLANKET WARMING CABINET
TRANSPORT AND STORAGE
Transport and Storage Environmental Conditions (not to exceed 15 days)
• Ambient temperature range of -40° to +159°F (-40° to +70°C)
• Relative humidity range of 10% to 100%, including condensation
• Atmospheric pressure range of 50KPa to 106KPa
UNPACKING AND SET-UP
DELIVERY
The Pedigo Warming Cabinet has been thoroughly
tested and inspected to insure only the highest
quality unit is provided. Upon receipt, check for
any possible shipping damage and report it at
once to the delivering carrier. See
Transportation Damage and Claims section
located in this manual.
This appliance, complete with unattached items
and accessories, may have been delivered in one
or more packages. Check to ensure that all
standard items and options have been received
with each model as ordered.
Save all the information and instructions packed
with the appliance. Complete and return the
warranty card to the factory as soon as possible
to assure prompt service in the event of a
warranty parts and labor claim.
This manual must be read and understood by all
people using or installing the equipment model.
Contact the Pedigo service department if you
have any questions concerning installation,
operation, or maintenance.
UNPACKING
1. Carefully remove the
appliance from the carton
or crate.
NOTE: Do not discard the
carton and other
packaging material
until you have
inspected the unit
for hidden damage
and tested it for
proper operation.
2. Read all instructions in this manual carefully
before initiating the installation of this
appliance.
DO NOT DISCARD THIS MANUAL.
This manual is considered to be part of the
appliance and is to be provided to the owner
or manager of the business or to the person
responsible for training operators.
Additional manuals are available from the
Pedigo service department.
3. Remove all protective plastic film, packaging
materials, and accessories from the appliance
before connecting electrical power.
NOTE: All claims for warranty must include the
full model number and serial number of
the unit.
1
SAFETY PROCEDURES AND PRECAUTIONS
Knowledge of proper procedures is essential to the safe operation of electrically and/or gas energized equipment. In accordance with generally accepted product safety labeling guidelines for potential hazards, the following signal words and symbols may be used throughout this manual.
Used to indicate the presence of a hazard that will cause severe personal injury, death, or substantial property damage if the warning included with this symbol is ignored.
Used to indicate the presence of a hazard that can cause personal injury, possible death, or major property damage if the warning included with this symbol is ignored.
Used to indicate the presence of a hazard that can or will cause minor or moderate personal injury or property damage if the warning included with this symbol is ignored.
Used to indicate the presence of a hazard that can or will cause minor personal injury, property damage, or a potential unsafe practice if the warning included with this symbol is ignored.
1. Pedigo blanket warmers are intended for warming cotton blankets ONLY. No other use for this device is authorized or recommended.
Pedigo fluid warmers are ONLY intended for warming medical solutions for irrigation and injection. The IRRIGATION MODE should be selected for warming irrigation fluids, and the INJECTION MODE should be selected for warming injection fluids. Please refer to the labeling of the manufacturer of the products to be warmed regarding the recommended temperature and the duration of warming. No other use for this device is authorized or recommended.
2. This device is intended for use in commercial establishments where all operators are familiar with the purpose, limitations, and associated hazards of this device. Operating instructions and warnings must be read and understood by all operators and users.
3. Any troubleshooting guides, component views, and parts lists included in this manual are for general reference only and are intended for use by qualified technical personnel.
4. This manual should be considered a permanent part of this device. This manual and all supplied instructions, diagrams, schematics, parts lists, notices, and labels must remain with the device if the item is sold or moved to another location.
Used to notify personnel of
NOTE:
installation, operation, or maintenance information that is important but not hazard related.
Pedigo warmers should not be left unattended for
Enthermics warmers should not be left unattended for
periods of more than 24 hours. In case of absences
periods of more than 24 hours. In case of absences
longer than 24 hours, disconnect the wamrer from
longer than 24 hours, disconnect the warmer from its
its power source.
power source.
2
PREPARATION
Before operating the cabinet, clean both the interior and exterior of the unit with a damp cloth and mild soap
solution. Rinse carefully. Wipe with an appropriate disinfectant. Clean and install the blanket support assembly.
Environmental conditions for operation: Maximum room ambient temperature of 89°F (32°C).
ELECTRICAL INFORMATION
The power specifications are located on the unit identification nameplate. This nameplate is
permanently attached to the unit and must be located to verify power requirements.
POWER REQUIREMENTS - P-2010
120 V.A.C. — 50/60 Hz, 1 ph 600 Watts, 5.5 Amps
Safety Class I Equipment
POWER REQUIREMENTS - P-2020
120 V.A.C. — 50/60 Hz, 1 ph 700 Watts, 6.0 Amps
Safety Class I Equipment
NEMA 5-15P 15A - 125V Plug Hospital Grade
NEMA 5-15P 15A - 125V Plug Hospital Grade
POWER REQUIREMENTS - P-2030
120 V.A.C. — 50/60 Hz, 1 ph 1000 Watts, 8.0 Amps
Safety Class I Equipment
Grounding reliability can only be achieved when equipment is
connected to an equivalent receptacle marked “Hospital Grade.”
Medical Equipment classified by Underwriters
Protective Earth Ground Symbol
Laboratories with Respect to Electrical Shock, Fire and Mechanical Hazards only, in Accordance with UL 60601-1 and CAN/CSA C22.2 No. 601.1.
NEMA 5-15P 15A - 125V Plug Hospital Grade
UL File No.
E201645
POWER REQUIREMENTS - P-2040
120 V.A.C. — 50/60 Hz, 1 ph 2000 Watts, 16.0 Amps
Safety Class I Equipment
NEMA 5-20P 20A - 125V Plug Hospital Grade
POWER REQUIREMENTS - P-2050
120 V.A.C. — 50/60 Hz, 1 ph 1600 Watts, 13.0 Amps
Safety Class I Equipment
POWER REQUIREMENTS - P-2055
120 V.A.C. — 50/60 Hz, 1 ph 1700 Watts, 14.2 Amps
Safety Class I Equipment
To prevent an electrical shock hazard between the appliance and other appliances or metal parts in close vicinity, an equalization-bonding stud is provided. An equalization bonding lead must be connected to this stud and the other appliances / metal parts to provide sufficient protection against potential difference. The terminal is marked with the following symbol.
NEMA 5-20P 20A - 125V Plug Hospital Grade
NEMA 5-20P 20A - 125V Plug Hospital Grade
DANGER
AT NO TIME SHOULD THE INTERIOR OR EXTERIOR BE STEAM CLEANED, HOSED DOWN, OR FLOODED WITH WATER OR LIQUID SOLUTION OF ANY KIND. DO NOT USE WATER JET TO CLEAN.
SEVERE DAMAGE OR
ELECTRICAL HAZARD
COULD RESULT.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
Hazardous
Voltage Present
DANGER
ENSURE POWER SOURCE MA TCHES VOLT A GE ST AMPED ON APPLIANCE NAMEPLATE.
3
GENERAL INFORMATION
This warming cabinet is designed to elevate blanket temperatures to a level which will increase patient comfort.
The warming cabinet is constructed with 20 gauge stainless steel exterior casing and door with handle and hinges designed to withstand heavy usage. A door with window allows observation of inventory with the door closed. The cabinet is warmed using the patented Halo Heat® low-heat-density electrothermal cable array. The electrothermal cable is positioned in the floor and two sides of the warming cabinet, providing even heating of the interior chamber. The interior chamber temperature is regulated by an electronic control. The design and operational characteristics of the cabinet eliminate the need for a heat circulating fan.
The electronic control consists of a 4 digit L.E.D. display, ON/OFF key, INCREASE and DECREASE keys, integrated LOCK feature and a series of prompt sequence indicators. The electronic control has an adjustable temperature range of 37° to 94°C (98° to 200°F). A warming shut-off system, separate from the electronic control, prevents overheating.
The TIMER key allows the user to program the control to automatically turn on and turn off once during a 24 hour period at selected times. The electronic control can easily be set to operate in Fahrenheit or Celsius. After a power failure, the cabinet will remember its programming and begin to operate as before. The ON/OFF indicator will blink to indicate a failure occurred; pressing the ON/OFF key once will eliminate this blinking.
P-2010 INFORMATION
The P-2010 warming cabinet is equipped with one (1) white, epoxy-coated blanket support assembly. The cabinet is furnished with four (4) 1-1/4" (31mm) non-skid rubber feet.
P-2020 INFORMATION
The P-2020 warming cabinet is equipped with one (1) white, epoxy-coated blanket support assembly and one (1) center shelf. The cabinet is furnished with one (1) set of 5" (127mm) heavy duty casters, two with locking brake.
P-2030 INFORMATION
The P-2030 warming cabinet is equipped with one (1) white, epoxy-coated blanket support assembly and one (1) center shelf. The cabinet is furnished with one (1) set of 5" (127mm) heavy duty casters, two with locking brake.
P-2040 INFORMATION
Each P-2040 chamber is equipped with one (1) white, epoxy­coated blanket support assembly and one (1) center shelf. The cabinet is furnished with one (1) set of 5" (127mm) heavy duty casters, two with locking brake.
P-2055 INFORMATION
Each P-2055 chamber is equipped with a white epoxy­coated blanket support assembly and two (2) center shelves. The cabinet is furnished with one (1) set of 5" (127mm) heavy duty casters, two with locking brake.
P-2050 INFORMATION
Each P-2050 chamber is equipped with a white epoxy­coated blanket support assembly. The cabinet is furnished with one (1) transport handle on each end of the cabinet, and a full-perimeter rubber bumper assembly with 5" (127mm) heavy duty casters, two with locking brake.
DANGER
AT NO TIME SHOULD THE INTERIOR OR EXTERIOR BE STEAM CLEANED, HOSED DOWN, OR FLOODED WITH WATER OR LIQUID SOLUTION OF ANY KIND. DO NOT USE WATER JET TO CLEAN.
SEVERE DAMAGE OR
ELECTRICAL HAZARD
COULD RESULT.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
DANGER
DO NOT use this warming cabinet in
the presence of flammable
anesthetic mixture (with air or with
oxygen or nitrous oxide).
THIS COULD RISK AN EXPLOSION!
4
P-2010 DIMENSIONS
17.63" (447.0mm)
6.00" (152.9mm)
27.57" (700.4mm)
33.63" (853.3mm)
OFF
ON
TIMER
TIME START STOP
LOCK
28.00" (711.2mm)
2.19" (55.4mm)
ELECTRICAL CONNECTION
20.07" (509.9mm)
39.63" (1005.9mm)
42.25" (1073.2mm)
8.82" (223.5mm) ELECTRICAL CONNECTION
TIME START STOP
ON
OFF
CAVITY
19.38" (492.8mm)
13.82" (351.4mm)
13.13" (333.2mm)
16.13" (409.0mm)
LOCK
TIMER
CAVITY
40.88" (988.0mm)
21.50" (546.7mm)
27.44" (696.9mm)
22.19" (580.1mm)
CAVITY
C
L
8.07" (204.5mm)
ELECTRICAL
18.69" (474.2mm)
ELECTRICAL CONNECTION
1.25" (31.4mm)
P-2020 DIMENSIONS
5
P-2030 DIMENSIONS
51.40" (1304.7mm)
22.10" (560.5mm)
REACH IN
31.70" (804.6mm)
28.80" (730.9mm)
(276.9mm)
10.90"
28.15" (714.9mm)
ON
OFF
10.90" (276.9mm)
24.24"
(616.4mm)
PASS THRU
72.75" (1847.7mm)
53.04" (1347.2mm)
28.80" (730.9mm)
21.48" (545.4mm)
53.05" (1347.6mm)
10.34"
(262.6mm)
2.19" (55.6mm)
Cavity
33.50" (851.7mm)
39.70" (1009.5mm)
26.8" (680.7mm)
18.80" (477.5mm)
Cavity
2.20" (55.6mm)
6.20" (157.9mm)
22.10" (560.5mm)
Cavity
33.50" (851.7mm)
26.80" (680.7mm)
39.70" (1009.5mm)
18.80" (477.5mm)
Cavity
33.35" (847.1mm)
6.20" (157.9mm)
6
REACH IN
22.10" (560.5mm)
P-2040 DIMENSIONS
51.30" (1304.2mm)
31.70" (803.9mm)
28.80" (730.9mm)
10.90 (276.6mm)
(276.9mm)
10.90"
ON
OFF
Cavity
26.80" (680.7mm)
66.40" (1686.2mm)
73.20" (1858.4mm)
Cavity
26.80" (680.7mm)
18.80"
(477.5mm)
Cavity
6.80" (172.2mm)
61.40" (1560.3mm)
PASS THRU
22.10" (560.5mm)
2.20" (56.4mm)
53.00" (1347.3mm)
72.70" (1847.5mm)
53.04" (1347.2mm)
33.35" (847.1mm)
28.78" (730.9mm)
7.3"
(184.15mm)
ON
OFF
Cavity
26.8" (680.66mm)
66.40" (1686.2mm)
73.20" (1858.4mm)
Cavity
26.80" (680.7mm)
18.80" (477.4mm)
2.20" (56.4mm)
6.80" (172.2mm)
Cavity
7
P-2050 DIMENSIONS
C
L
Electrical Connection
2.21" (56.0mm) from top
P-2055 DIMENSIONS
4.01"
(101.6mm)
4.11"
(104.2mm)
30.07" (763.6mm)
31.29" (794.5mm)
1.63" (41.3mm)
58.82" (1493.9mm)
66.29" (1683.7mm)
30.21" (767.1mm)
Cavity
56.71" (1440.2mm)
1.22" (30.8mm)
54.33" (1381.1mm)
27.22" (691.2mm)
24.01" (609.6mm)
64.09" (1627.8mm)
70.82" (1798.7mm)
37.88" (962.0mm)
6.38" (161.9mm)
(170.9mm)
6.73"
26.53" (673.8mm)
Cavity
8
BLANKET CONTROL FEATURES
ON
OFF
LOCK
TIME START
STOP
L.E.D.
DISPLAY
STATUS INDICATOR L.E.D. UP ARROW
DOWN ARROW AUTO TIMER
KEY
ON / OFF
KEY
L.E.D. = LIGHT EMITTING DIODE
TIMER
THERMOSTAT CONTROL AND L.E.D. DISPLAY
The following refers to features that are available when the control is powered on. When an audible alarm is referenced, the unit will only beep if the audible alarm feature is selected.
CONTROL PANEL KEYS
ON/OFF KEY
Press the ON/OFF key to power on the control. Press and hold the ON/OFF key for 2 seconds to power the control off. The control will beep for one second when turned on or off, and the status indicator light will illuminate according to the power state.
UP ARROW / DOWN ARROW KEYS
Used to increase or decrease the temperature set-point. Additionally used to set the current time, auto-start, and auto-stop times.
TIMER KEY
Blanket warmers have a timer key which is used to program the time of day, as well as the automated start and stop times. To set the start and stop times, press and hold the timer key for 2 seconds. See “Setting the Time” instructions on this page.
L.E.D. DIGITAL DISPLAY
The control has a four-digit L.E.D. display. When the control is activated, the display will show current temperature set-point. When programming the timer, the display will show hour and minutes.
L.E.D. DISPLAY STATUS INDICATORS
TIME
Illuminates while current time of day is displayed when programming the TIMER mode.
START
Illuminates while the start time is displayed when programming the TIMER mode.
STOP
Illuminates while the stop time is displayed when programming the TIMER mode.
LOCK
Illuminates when the lock feature is engaged.
POWER FAIL DETECTION
If the power were to fail for any reason while heating, the warmer will retain its current operating state in memory. When the power is restored, the control will resume operating, but several indicators will alert the operator that such an event has occurred:
A. The ON/OFF status indicator will flash.
B. Display will indicate ‘128’ (or another number)
alternating with the setting. Please see important note below if a number other than ‘128’ is displayed.
C. Control will beep until the power failure is
acknowledged.
Press the ON/OFF key once to acknowledge that the power has been restored. The ON/OFF status indicator will stop flashing and the “beep” will be silenced. The display will indicate the approximate time period of the outage, then return to the normal display and previously set mode.
NOTE: The display of ‘128’ is a normal Power-On Reset
for the control. Any other number displayed may indicate a problem. Make note of the number, and if the unit fails to operate properly, provide that number to service to assist them in troubleshooting the problem.
TEMPERATURE FORMAT SELECTION
While the controller is in the off mode, press and hold the UP ARROW key for 4 seconds to switch between Fahrenheit or Celsius.
AUDIBLE ALARM SELECTION
While the controller is in the off mode, press and hold the DOWN ARROW key for five seconds to switch between audible alarm “ON” and “OFF” modes. When the audible alarm is in the “OFF” mode, an audible alarm will still sound if there is an OVERTEMP error, the door is left open for more than 2 minutes, or in the event of power loss.
SETTING THE DATE AND TIME NOTES: If you do not wish to use the automated timer feature,
then you do not need to set the date and time and this section can be skipped. All times will be displayed in hours and minutes (HH:MM) in a 24-hour format. 1:00pm will display as 13:00. The clock will need to be manually reset for Daylight Saving Time.
While the unit is off, hold the TIMER button for 2 seconds to display the year (2000-2099). Adjust the year up or down using the arrow buttons. Press the TIMER button again to transition to the month and day (MM.DD). Adjust the month and day up or down. Press the TIMER button again to enter the time set mode. The current time of day will show on the display in 24-hour format (HH:MM). Adjust the time up or down. Press the TIMER button again to transition to the Auto-On Time. The
9
BLANKET CONTROL FEATURES (CONTINUED)
POWER
CIRCUIT BREAKER
SWITCH
currently programmed Auto-On time will show on the display in 24-hour format. This is the time that the control will automatically turn on when enabled. Adjust to desired time. Press the TIMER button again to transition to the Auto-Off Time. The currently programmed Auto-Off time will show on the display. This is the time the control will automatically turn off when enabled. Adjust to desired time. Press the TIMER button again to enable the Auto­Timer feature. The Time indicator light will turn on. To disable, press and hold the TIMER key for 2 seconds and the indicator light will turn off.
When adjusting the TIMER with the unit on, the year and date will not be adjustable, and will start the programming sequence with the current time of day.
BLANKET CHAMBER OPERATIONAL PROCEDURES
1. The appliance should be plugged into a hospital grade, NEMA 5-20P receptacle
receptacle for a 230V appliance.
2. Turn on the power circuit breaker switch, which is located at the back of the appliance. It is a rocker-type switch with international ON (I) and OFF (O) markings.
3. ACTIVATE CONTROL BY PRESSING THE ON/OFF KEY ON CONTROL PANEL ONCE. The ON/OFF indicator will illuminate and remain lit until the unit is turned off. The digital L.E.D. display will indicate last temperature set-point of compartment.
4. SET DESIRED TEMPERATURE. To set the blanket warming temperature, press and hold the UP or DOWN ARROW keys to change the value shown in the display. The temperature set-point range is 98 - 200°F (37 - 93°C).
5. LOAD THE CHAMBER WITH 100% COTTON
BLANKETS. DO NOT WARM SYNTHETIC BLEND FABRICS OR ITEMS CONTAINING PLASTIC, RUBBER OR METAL SNAPS, STUDS, HOOKS, ETC.
Check that the epoxy-coated blanket support assembly and shelf is in place. This blanket support assembly and shelf MUST be used to hold blankets. A full load of blankets will take 2-3 hours to reach optimum temperature. Make certain the cabinet door is securely closed after initial loading and following each blanket removal.
Note: Do not block sensor by overloading cabinet
with blankets.
6. ROTATE LOAD OF BLANKETS DAILY. Rotate the blankets at the bottom of the load to the top to ensure equal usage. Failure to rotate blankets can cause blankets to discolor.
Note: Avoid using flammable cabinet cleaning agents,
as well as blanket cleaning agents that cause fabric to become brittle over time.
(120V) or an appropriate
NOTE:
When the Auto-On Time and the Auto-Off Times are equal, the unit will recognize the Auto-Off time ONLY and the control will never turn on without user intervention.
USING THE CONTROL LOCK
The warmer control can be locked so that no changes can be made to the temperature set-point or the mode selection. Press the ON/OFF key and the UP arrow key at the same time. The LOCK indicator will illuminate. Attempts to operate the ON/OFF key, or to change the temperature set-point will be unsuccessful. To unlock the warmer control, press the ON/OFF key and the DOWN arrow button at the same time. The control will unlock and the LOCK indicator will extinguish.
or
POWER ON/OFF
ROCKER SWITCH
CAUTION
BLANKET SUPPORT ASSEMBLY AND SHELF
MUST BE USED WHEN WARMING BLANKETS.
CAUTION
DO NOT O VERLO AD CABINET.
BLANKETS MUST NOT EXCEED HEIGHT OF
SUPPORT ASSEMBLY . ALLOW 1" GAP BETWEEN
LOWER BLANKETS AND MIDDLE SHELF.
Load blankets only to the top of the
blanket support assembly.
10
CLEANING AND PREVENTIVE MAINTENANCE
PROTECTING STAINLESS STEEL SURFACES
It is important to guard against corrosion in the care of stainless steel surfaces. Harsh, corrosive, or inappropriate chemicals can completely destroy the protective surface layer of stainless steel. Abrasive pads, steel wool, or metal
implements will abrade surfaces causing damage to this protective coating and will eventually result in areas of corrosion. Even water, particularly hard water that contains high to moderate concentrations of chloride, will cause oxidation and pitting that result in rust and corrosion. In addition, many acidic spills left to remain on metal surfaces are contributing factors that will corrode surfaces.
Proper cleaning agents, materials, and methods are vital to maintaining the appearance and life of this appliance. Spilled items should be removed and the area wiped as soon as possible but at the very least, a minimum of once a day. Always thoroughly rinse surfaces after using a cleaning agent and wipe standing water as quickly as possible after rinsing.
CLEANING AGENTS
Use non-abrasive cleaning products designed for use on stainless steel surfaces. Cleaning agents must be chloride-free compounds and must not contain quaternary salts. Never use hydrochloric acid (muriatic acid) on stainless steel surfaces. Always use the proper cleaning agent at the manufacturer's recommended strength. Contact your local cleaning supplier for product recommendations.
CLEANING MATERIALS
The cleaning function can usually be accomplished with the proper cleaning agent and a soft, clean cloth. When more aggressive methods must be employed, use a non­abrasive scouring pad on difficult areas and make certain to scrub with the visible grain of surface metal to avoid surface scratches. Never use wire brushes, metal scouring pads, or scrapers to remove residue.
ANNUAL PREVENTATIVE MAINTENANCE
1. Ensure that the correct Operation and Care manual is available to all users.
2. Ensure that all users have been properly trained in unit’s operation.
3. Do not exceed the unit’s capacity.
4. Inspect condition of plug and cord. Replace if damaged.
5. Clean dust from outer vents surrounding the unit and around top of bonnet.
6. Check door gasket. Are there any tears? Is the gasket worn or loose? Make sure seal is tight to unit body. Replace gasket if integrity is compromised.
7. Check air temperature sensor mounted on the interior of chamber. Is the metal guard in place? Are the wires in good condition?
8. Check the blanket support assembly and shelf (if applicable) Is the assembly in place? Are any pieces missing?
9. Check basket and side rail condition (if applicable). Do baskets move smoothly and freely?
10. check caster or leg condition. Ensure mounting bolts and assembly is secure.
11. Check control panel overlay condition. Are there any tears or excessive wear on the graphic? Does control work properly when buttons are pushed?
12. Check that all control LEDs light up as applicable.
13. Is the Set Temperature comparable to the Actual temperature displayed? If not, control needs calibration. Call Service.
Contact Service for immediate repair if any of the above problems exist.
N
O
N
N
CAUTION
A
R
P
C
E
S
R
O
E
R
I
W
E
T
S
O
TO PROTECT STAINLESS STEEL
S
SURFACES, COMPLETELY AVOID THE USE OF ABRASIVE CLEANING COMPOUNDS, CHLORIDE BASED
B
R
U
S
H
CLEANERS, OR CLEANERS
E
S
CONTAINING QUATERNARY SALTS. NEVER USE HYDROCHLORIC ACID (MURIATIC ACID) ON STAINLESS
E
L
P
A
D
S
STEEL. NEVER USE WIRE BRUSHES, METAL SCOURING PADS OR SCRAPERS.
11
CARE AND CLEANING
The cleanliness and appearance of this equipment will contribute considerably to its operating efficiency. Make certain the cabinet and door gasket are kept free of any debris that may accumulate. Good equipment that is kept clean works better and lasts longer.
CLEAN THE UNIT REGULARLY:
1. Disconnect the cabinet from the power source.
2. Remove all detachable items such as the metal basket and basket rail supports. Clean these items separately.
NOTE: Avoid the use of abrasive cleaning compounds, chloride based cleaners, or cleaners containing quaternary salts. Never use hydrochloric acid (muriatic acid) on stainless steel.
3. Clean the interior metal surfaces of the cabinet with a damp cloth and any mild commercial detergent. Avoid the use of abrasive cleaning compounds. Rinse surfaces by wiping with sponge & clean warm water. Remove excess water with sponge and wipe dry with a clean cloth or air dry. Leave doors open until interior is completely dry.
4. Interior can be wiped with a sanitizing solution after cleaning and rinsing. This solution must be approved for use on stainless steel surfaces. Replace blanket support assembly.
5. To help maintain the protective film coating on polished stainless steel, clean the exterior of the cabinet with a cleaner recommended for stainless steel surfaces. Spray the cleaning agent on a clean cloth and wipe with the grain of the stainless steel.
6. Clean the window glass with a standard commercial glass cleaner.
7. Wipe control panel, door vents, door handles, and door gaskets thoroughly since these areas harbor debris.
8. Wipe door gaskets and control panel dry with a clean, soft cloth.
Always follow appropriate state or local health (hygiene) regulations regarding all applicable cleaning and sanitation requirements.
9. To help maintain the protective film coating on polished stainless steel, clean the exterior of the cabinet with a
cleaner recommended for stainless steel surfaces. Spray the cleaning agent on clean closth a wipe with grain of the stainless steel.
DANGER
AT NO TIME SHOULD THE INTERIOR OR EXTERIOR BE STEAM CLEANED, HOSED DOWN, OR FLOODED WITH WATER OR LIQUID SOLUTION OF ANY KIND. DO NOT USE WATER JET TO CLEAN.
DANGER
SEVERE DAMAGE OR
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
ELECTRICAL HAZARD
COULD RESULT.
WARRANTY BECOMES VOID IF
APPLIANCE IS FLOODED
(Listed as Ordinary Equipment.)
12
If your unit is not operating properly, check the following before calling your authorized service agent. Check the power applied to the unit. Is the plug in outlet? Is the power circuit breaker switch in rear of unit OK? Has the high limit manual reset tripped? If so, reset. (See “Manual Reset Instructions” below.)
If temperature calibration adjustment is required, call Enthermics Service for proper instruction.
Do not attempt to repair or service beyond this point. Contact manufacturer for nearest authorized service agent. Repairs made by any other service agent without prior authorization by manufacturer will void the warranty on the unit.
This chart is provided for the assistance of qualified technicians only and is not intended for use by untrained or unauthorized service personnel.
TROUBLE SHOOTING GUIDE
ERROR DESCRIPTION ACTION REQUIRED
E-10 Sensor Short • Detach the sensor from the terminal block. Use an Ohm meter to measure the resistance of
E-11 Sensor Open • Detach the sensor from the terminal block. Use an Ohm meter to measure the resistance of
E-30 Under Temp Error
(Blanket warmers only)
E-31 Over Temp • Unit may be overloaded. Redistribute inventory. Do not exceed height of basket assembly.
E-60 Real-Time Clock Checksum Error • Unit may have been unplugged for an extended period of time.
E-80 EPROM Data • Call Service. E-81 Calibration Values Out of
Expected Range E-82 Calibration Data Error • Call Service. E-99 Hardware Over Temp • Inspect connections and condition of high limit bimetal thermostat.
the sensor. Check sensor at 32°F (0°C) using a container of ice water. If Ohm reading is 100, replace display. If Ohm reading is ±10, replace sensor.
• Check wires for integrity. Check for proper and secure connections at the control and terminal block. If necessary, re-secure the faulty connections.
• If error continues call Service.
the sensor. Check sensor at 32°F (0°C) using a container of ice water. If Ohm reading is 100, replace display. If Ohm reading is ±10, replace sensor.
• Check wires for integrity. Check for proper and secure connections at the control and terminal block. If necessary, re-secure the faulty connections.
• If error continues call Service.
• Blanket chamber temperature has been lower than the set temperature for 90 minutes or longer.
• Check that door is closed.
• Verify that the high limit switch located at the rear of the unit has not been tripped. If it has been tripped, reset by pressing in the limit reset button. After resetting, the cause of the high limit trip must be corrected. If the high limit switch will not reset, the high limit switch is defective and must be replaced. This is a safety device and must not be jumped out or removed from the
circuit.
• Check sensor at 32°F (0°C) using a container of ice water. The sensor reading should be 100 ohms.
• Relay (solid state) may be defective.
• Control may have defective temperature circuit.
• If error continues call Service.
• To resolve, turn circuit breaker switch to ON position for 1 minute, then turn circuit breaker switch to the OFF position for 5 seconds, and then back to ON. The error message should no longer appear in the display.
• In order for the unit to fully recharge, it should remain plugged in and power circuit breaker switch turned ON for at least 24 hours after resetting.
• Upon resolving an E-60 error, check that the date and time are correct.
• Call Service.
• If error continues call Service.
NOTE: All error codes must be cleared using the circuit breaker switch or power cord on the rear of the unit.
Manual Reset Instructions: Locate the manual reset button on back of unit. Using a pen, screwdriver or other long, thin
implement, firmly push reset button. You will hear an audible click when the button is reset. If reset button trips again while unit is running, contact a qualified service technician.
DANGER
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING.
Manual reset button Circuit breaker
13
SH-25909
BLANKET SUPPORT
ASSEMBLY,
SIDES
Service Views of P-2010
PE-25687
CONTROL PANEL
OVERLAY
E5078
WINDOW DOOR
ASSEMBLY
HD-2007
DOOR
HANDLE
SH-25910
BLANKET SUPPORT
ASSEMBLY, BOTTOM
SN-
33541
SENSOR
BM-22606
BUMPER FEET
HG-2015
HINGE
E2132GS
DOOR GASKET
ASSEMBLY
15
TT-34350
THERMOSTAT,
HI-LIMIT
RL-34434
RELAY
Service Views of P-2010
4 PIN CONNECTOR
CC-34423
CONTROL ASSEMBLY
CR-33717
10 PIN CONNECTOR
CR-33763
CR-33718
9 PIN CONNECTOR
BP-3567
SOLID STATE
BEEPER
BA-34041
POWER SUPPLY
BOARD
BK-3019
TERMINAL
BLOCK
BU-3964
STRAIN RELIEF
BUSHING
E3025CD
HOSPITAL
GRADE
CORDSET
BK-33546
PORCELAIN
TERMINAL
BLOCK
SC-2190
GROUND
SCREW
SW-33826
CIRCUIT BREAKER
SWITCH
16
P-2010 Wiring Diagram
17
Service Views of P-2020
E2150PE
CONTROL PANEL OVERLAY
HG-22338
HINGE SET
E5056
WINDOW DOOR
ASSEMBLY, RH
SN-33541
SENSOR
SH-25912
CENTER SHELF
SH-25905
BLANKET SUPPORT
ASSEMBLY
CS-2025
CASTERS
5" (127mm), RIGID
CS-2026
CASTERS 5"(127mm),
SWIVEL W/ BRAKE
HD-24171
DOOR HANDLE
GS-22950
DOOR GASKET
ASSEMBLY
E2150PE
CONTROL PANEL
OVERLAY
SN-33541
SENSOR
SH-25905
BLANKET SUPPORT
ASSEMBLY
19
Service Views of P-2020
CC-34423
CONTROL ASSEMBLY
BA-34041
POWER SUPPLY BOARD
BK-3019
TERMINAL BLOCK
CR-33717
CONNECTOR, 10 PIN
CR-33763
CONNECTOR, 4 PIN
CR-33718
CONNECTOR, 9 PIN
BP-3567
BEEPER,
SOLID STATE
RL-34434
RELAY
SC-2190
GROUND SCREW
BU-3964
STRAIN RELIEF
BUSHING
E3025CD
CORDSET,
HOSPITAL GRADE
SW-33826
POWER CIRCUIT
BREAKER SWITCH
SW-33826
POWER CIRCUIT
BREAKER SWITCH
20
P-2020 Wiring Diagram
21
Service Views of P-2030
SN-33541
SENSOR
SH-25911
BLANKET SUPPORT
ASSEMBLY, SHELF
SH-25908
BLANKET SUPPORT
ASSEMBLY, SIDES
E2156PE
CONTROL PANEL OVERLAY
HG-22338
HINGE SET
5001253
WINDOW DOOR
ASSEMBLY, RH
HD-24171
DOOR
HANDLE
5” (127mm)
CASTERS, RIGID
E2156PE
CONTROL PANEL
OVERLAY
SN-
33541
SENSOR
CS-2025
CS-2026
5” (127mm) CASTERS,
SWIVEL W/ BRAKE
GS-23794
DOOR GASKET
ASSEMBLY
23
Service Views of P-2030
CC-34423
CONTROL ASSEMBLY
CR-33717
CONNECTOR, 10 PIN
CR-33763
CONNECTOR, 4 PIN
CR-33718
CONNECTOR, 9 PIN
BP-3567
BEEPER,
SOLID STATE
RL-34434
RELAY
BA-34041
POWER
SUPPLY BOARD
SC-2190
GROUND SCREW
SW-33826
POWER CIRCUIT
BREAKER SWITCH
BK-3019
TERMINAL BLOCK
24
P-2030 Wiring Diagram
25
Service Views of P-2040
CONTROL PANEL
SH-25911
CENTER SHELF
E3029CD
CORDSET,
HOSPITAL GRADE
SH-25908
BLANKET SUPPORT
ASSEMBLY
E2157PE
OVERLAY
SN-33541
SENSOR
5001253
WINDOW DOOR
ASSEMBLY, RH
HD-24171
DOOR HANDLE
GS-23794
DOOR GASKET
ASSEMBLY
CS-24983
5" (127mm) CASTER,
RIGID
E2157PE
CONTROL PANEL
OVERLAY
SN-33541
SENSOR
HG-22338
HINGE SET
CS-24984
5" (127mm) CASTERS,
SWIVEL W/BRAKE
27
Service Views of P-2040
CR-33717
CONNECTOR, 10 PIN
CC-34423
CONTROL ASSEMBLY
CR-33763
CONNECTOR, 4 PIN
CR-33718
CONNECTOR, 9 PIN
BP-3567
BEEPER,
SOLID STATE
RL-34434
RELAY, DPST, 25A,
12V DC COIL
BK-3019
TERMINAL BLOCK
E3029CD
CORDSET,
HOSPITAL GRADE
BU-3964
STRAIN RELIEF
BUSHING
BA-34041
POWER SUPPLY
BOARD
SW-33858
POWER CIRCUIT
BREAKER SWITCH
28
P-2040 Wiring Diagram
29
Service View of P-2050
PE-25578
CONTROL PANEL
OVERLAY
OP-26670
FALSE SIDES
HD-2861
UNIT HANDLE
OP-26671
CENTER SHELF
OP-26669
BLANKET
SUPPORT, UPPER
OP-26672
BLANKET
SUPPORT, LOWER
E5092
WINDOW DOOR
ASSEMBLY, RH
HD-24171
DOOR HANDLE
E2125GS
DOOR
GASKET
HD-24171
DOOR
HANDLE
CS-24984
CASTER, 5" (127mm),
SWIVEL W/ BRAKE
SN-33541
SENSOR
5001776
FULL-PERIMETER RUBBER
BUMPER ASSEMBLY
CS-24983
CASTER, 5" (127mm),
RIGID
31
Service View of P-2050
CR-33717
CONNECTOR, 10 PIN
CC-34423
CONTROL ASSEMBLY
CR-33763
CONNECTOR, 4 PIN
CR-33718
CONNECTOR, 9 PIN
RL-34434
RELAY, DPST, 25A,
12V DC COIL
GROUND SCREW
SC-2190
BP-3567
BEEPER,
SOLID STATE
BA-34041
POWER SUPPLY BOARD
BK-3019
TERMINAL BLOCK
SW-33858
CIRCUIT BREAKER SWITCH
BU-3964
STRAIN RELIEF
BUSHING
32
E3029CD
CORDSET,
HOSPITAL GRADE
P-2050 Wiring Diagram
33
Service View of P-2055
PE-26650
CONTROL PANEL
OVERLAY
5003587
BLANKET
SUPPORT, UPPER
1003115
CENTER SHELVES
5003586
BLANKET
SUPPORT, LOWER
HG-2015
DOOR HINGES
HD-24171
DOOR
HANDLE, TOP
5003583
WINDOW DOOR
ASSEMBLY, RH
GS-26634
DOOR
GASKET
HD-24171
DOOR HANDLE,
BOTTOM
CS-24874
CASTER,
5" (127mm), RIGID
SN-33540
SENSOR
CS-24875
CASTER, 5" (127mm),
SWIVEL W/ BRAKE
35
Service View of P-2055
BA-34041
POWER SUPPLY BOARD
CC-34423
CONTROL ASSEMBLY
CR-33717
CONNECTOR, 10 PIN
CONNECTOR, 4 PIN
CR-33763
CR-33718
CONNECTOR, 9 PIN
BP-3567
BEEPER,
SOLID STATE
RL-34434
RELAY, DPST, 25A,
12V DC COIL
SC-2190
GROUND SCREW
SW-33858
CIRCUIT
BREAKER SWITCH
BK-3019
TERMINAL BLOCK
36
SW-33858
CIRCUIT BREAKER SWITCH
E3029CD
CORDSET,
HOSPITAL GRADE
TRANSPORTATION
PEDIGO
DAMAGE AND CLAIMS
All Pedigo equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments become the property of the consignee.
Should damage occur in shipment, it is a matter between the carrier and the consignee. In such cases, the carrier is assumed to be responsible for the safe delivery of the merchandise, unless negligence can be established on the part of the shipper.
1. Make an immediate inspection while the equipment is still in the truck or immediately after it is moved to the receiving area. Do not wait until after the material is moved to a storage area.
2. Do not sign a delivery receipt or a freight bill until you have made a proper count and inspection of all merchandise received.
3. Note all damage to packages directly on the carrier’s delivery receipt.
4. Make certain the driver signs this receipt. If he refuses to sign, make a notation of this refusal on the receipt.
5. If the driver refuses to allow inspection, write the following on the delivery receipt:
Driver refuses to allow inspection of containers for visible damage.
6. Telephone the carrier’s office immediately upon finding damage, and request an inspection. Mail a written confirmation of the time, date, and the person called.
7. Save any packages and packing material for further inspection by the carrier.
8. Promptly file a written claim with the carrier and attach copies of all supporting paperwork.
LIMITED WARRANTY
Pedigo Products, Inc. warrants to the original purchaser that any original part that is found to be defective in material or workmanship will, at our option, subject to provisions hereinafter stated, be replaced with a new or rebuilt part.
The labor warranty remains in effect one (1) year from installation or fifteen (15) months from the shipping date, whichever occurs first.
The parts warranty for the cavity fan motor remains in effect one (1) year from installation or fifteen (15) months from the shipping date, whichever occurs first. The parts warranty on all other parts remains in effect three (3) years from installation or thirty-nine (39) months from the shipping date, whichever occurs first.
This warranty does not apply to:
1. Calibration
2. Equipment damage caused by accident, shipping, improper installation or alteration.
3. Equipment used under conditions of abuse, misuse, carelessness or abnormal conditions including equipment subjected to harsh or inappropriate chemicals including but not limited to compounds containing chloride or quaternary salts, poor water quality, or equipment with missing or altered serial numbers.
4. Any losses or damage resulting from malfunction, including loss of contents or consequential or incidental damages of any kind.
5. Equipment modified in any manner from original model, substitution of parts other than factory authorized parts, removal of any parts including legs, or addition of any parts.
6. Collateral or incidental damage as a direct result of servicing equipment built into a wall structure is not covered under warranty. It is the responsibility of the owner to bear all expense related to structural repairs including, but not limited to, external electrical connections and wiring, and the removal or replacement of caulk, grout, tile, or wall covering of any kind. A service access panel for built-in equipment installations is strongly recommended.
This warranty is exclusive and is in lieu of all other warranties, expressed or implied, including the implied warranties of merchantability and fitness for purpose. In no event shall the Company be liable for loss of use, loss of revenue, or loss of contents or revenue, or for indirect or consequential damages. This warranty is in lieu of all other warranties expressed or implied and Pedigo Products, Inc. neither assumes nor authorizes any persons to assume for it any other obligation or liability in connection with Pedigo Products, Inc. equipment.
We will continue our policy of assisting our customers in collecting claims which have been properly filed and actively pursued. We cannot, however, file any damage claims for you, assume the responsibility of any claims, or accept deductions in payment for such claims.
4000 SE COLUMBIA WAY VANCOUVER WA 98661
Record the model and serial numbers of the unit for easy reference. Always refer to both model and serial numbers in your correspondence regarding the unit.
Model: _____________________________________________________
Serial Number: _______________________________________________
Purchased From: ______________________________________________
Date Installed: _________________ Voltage: ____________________
ALL PEDIGO PRODUCTS ARE PROUDLY MADE IN THE USA
800.822.3501
4/09 MM-1069
FAX 360.696.1700 www.pedigo-usa.com
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use