Bass Guitar
Owner's Manual
Bass Guitar Configuration
4
5
6
3
8
7
9
3
1. Volume
2. Tone Controls
3. Strap Button
4. Bridge
2
1
5. Bridge Pickup
6. Neck Pickup
7. Position Markers
8. Fret
9. Fingerboard
10. Nut
11. Tuning Keys
12. String Retainer
10
12
11
Control Configuration
blend bass
treble
tone
volume
treble bridge volume tone neck volume neck volume bridge volume tone
Congratulations
So, you are the owner of a new Peavey Bass Guitar. Congratulations! Your
purchase proves your taste in musical instruments is superb. Peavey offers a wide
variety of bass guitars for beginners to professionals, each with unique qualities and
features. While our professional luthiers have carefully inspected your guitar, every
model requires some initial setup, and periodic maintenance is required for peak
performance.
To ensure proper care of your quality instrument, visit www.peavey.com/accessories
for Peavey-recommended accessories, parts and cleaning supplies.
When properly cared for, your Peavey bass will offer you years of pleasure.
Playing your bass means that you will need to perform regular, general
maintenance, such as cleaning and proper storage, to keep it looking and
sounding great.
Every time you play your bass, body oils and perspiration are transferred to the
body, back of the neck, headstock, ngerboards, strings, tuners, pickups and
bridge. After you nish performing, but before you put your bass away, take a
moment to remove these contaminants.
Cleaning & Care
Cleaning - Wood
To clean and care for the major wood parts of your bass guitar (body,
headstock and the back of the neck), Peavey recommends that you
use a clean, soft, lint-free, dry cotton cloth and the specially
formulated guitar polish available at www.peavey.com/acces-
sories. Use of an inappropriate rag or polish may result in
scratching the nish of your instrument.
WARNING: Peavey recommends that you do not
use abrasives or solvents on your instrument.
Cleaning - Fingerboard
Properly caring for your ngerboard requires special attention. Over time, a ngerboard may lose its
natural oils and shrink or exhibit a worn or faded appearance. Peavey recommends that you periodically
apply a small amount of Lemon Oil (available at www.peavey.com/accessories) to your ngerboard (after removing strings) using a clean, soft, lint-free, dry cotton cloth, taking the care to remove excess oil
immediately. A little goes a long way! How do you know when it is time to reapply? You can watch for a
change in the appearance of your wood, or set a routine calendar date. However, do not allow too much
time to pass as permanent damage may occur. If you allow the wood on the ngerboard to dry out and
shrink, the frets will “stand out” and feel rough to the touch.
Cleaning - Metal
To clean and lubricate the major metal parts of
your bass (strings, pickups, bridge, tuners), Peavey
recommends that you use a clean, soft, lint-free,
dry cotton cloth and the specially formulated guitar
string cleaner available at
www.peavey.com/accessories. Don’t just wipe down
the tops of your strings. Individually clean strings
by wrapping each one in a fold of cloth, running
it back and forth along the string’s entire length
until the cloth fails to pick up any more residue.
Failure to routinely clean and lubricate the
metal parts of your instrument, including
strings, may result in rusting.
WARNING: Peavey recommends that you
do not use abrasives or solvents on your
instrument.
Your bass is a piece of art that must be pro-
tected. When you are traveling with your instru-
ment, loosen the tuning knobs a turn or two to
take pressure off the neck, and protect it with
a gig bag or case. While a gig bag offers some
protection, mainly from dust, a hardshell case
offers the best protection. If you plan to store
your bass for a long period of time (we don’t
know why you would want to), remember to
slightly loosen your strings to relieve pressure
on the neck. As with any piece of art, don’t
throw it in your trunk and leave it in -10° or 110°
weather! Always keep you bass stored at room
temperature, and avoid extreme changes in
temperature or humidity.
Storage & Travel
Accessories
Add-on products like stands, hangers and straps that are made of plastic, rubber
or man-made materials may chemically or physically react with and damage the
nish of your Peavey bass. Peavey offers a full line of safe accessories at
www.peavey.com/accessories.
Every player needs a strap for peak performance; however, straps and strap
buttons are designed for “ordinary” use. If you anticipate “above ordinary” use,
Peavey recommends that you use Super Strap Locks to secure your strap to your
bass (see www.peavey.com/accessories).
REMEMBER: Peavey Care Kits offer the best
value for your money. Check them out at
www.peavey.com/accessories!
10
Old strings can produce dull, buzzing or dead notes, but a new set
of strings will ring clear and true. If you play often, you will need
to change your strings often. A good rule of thumb is that if you
play daily, you should change strings every two to three weeks.
Replace your strings as you notice them becoming dirty or discolored, before you experience a disappointing loss of performance.
See page 1 for detailed instructions on changing strings.
11
11
Strings
Changing Your Strings
Unless you are reconditioning your fretboard (see Cleaning &
Care, p.), strings should be changed one at a time to maintain
proper neck tension. New strings should be free of defects
(twists, kinks, bends) that can cause sound irregularities or
breakage. All strings must be stretched upon installation.
After your rst tuning, carefully pull each string away from the
fretboard, stretching it gently (too much force will break thinner
strings). Then, retune your guitar.
Peavey recommends that you replace strings in the same
gauges to maintain proper neck and/or bridge tension. If you
wish to change strings with different gauges, Peavey recommends that you enlist the services of a qualied technician to
make the required truss rod and/or bridge adjustments on your
instrument.
1
Standard Tuning
(thickest string to thinnest)
-String Bass Tuning
Open note E A D G
String 4 3 2 1
-String Standard Low B
Adds one lower-pitched string
Open note B E A D G
String 5 4 3 2 1
-String Alternative High C
Adds one higher-pitched string
Open note E A D G C
String 5 4 3 2 1
6-String Bass Tuning
Open note B E A D G C
String 6 5 4 3 2 1
Changing Your Strings
Changing strings on a Peavey bass guitar is a simple task that will bring new life to your instrument.
Tools Needed:
Wire cutters
Electronic tuner or pitch pipe (optional)
Note: Peavey recommends changing one string at a time to maintain proper tension on the neck and
bridge. Replace strings with the same gauges or you will need to make truss rod, spring tension and
intonation adjustments as described in this manual.
First, detune the thickest, top string (the 6th, th or th string, depending on your model) using the
machine head tuner—two or three full turns should remove the tension on the string. Remove the string
from the tuning peg; at the other end of the string, pull the ball end of the string and remove the string
from the instrument. (You may wish to cut off the portion of the string previously wound around the tuning peg to make this task easier.)
1
Changing Your Strings
Following the path of the string you just removed, insert the plain end of a new string through the hole
in the bridge and thread across the string saddle, up the ngerboard, across the nut, through the string
guide (if one is provided), and into the small hole in the corresponding machine head tuning post. (The
ball end of the string will secure the string to the bridge.) At the headstock, allow - inches of string
beyond the post for turning around the machine head post, then cut the excess string. Insert the freshly
cut string end into the hole in the center of the tuning post. Then, bend the string at a right angle at the
edge of the slot and begin winding the string onto the post. Note that the string path should be straight,
running from the fretboard, over the nut, through the string guides (if provided), to the post—without
angling off. To avoid slippage, wind strings tightly from top to bottom on each post, completing -
wraps around each post. Keep light pressure on the string with the ngers of your other hand while
tightening the string using the tuners. (An inexpensive peg winder makes winding much easier.) Tune
to pitch. Because new strings are prone to stretch when rst installed, you should gently stretch each
string by pulling it away from the neck and retune again.
1
Changing Your Strings
Note: Do not make saddle adjustments unless you are changing string gauges, which also requires
truss rod and intonation adjustments.
Repeat this procedure for the remaining strings, remembering to tune each to pitch before proceeding
to the next string. Hint: To prevent detuning from slippage, always tune UP to the correct pitch. Retune
each string until strings hold their relative pitch to one another.
1
Tuning Machine Adjustments
Over time, tuners can become loose. Get in the habit of checking the tension with every string change. If
you notice a change in the tension of a tuner, use a small athead or Phillips screwdriver (some require
an allen wrench) to tighten it (turn clockwise) or loosen it (turn counterclockwise) accordingly.
Warning: While the screw should be snug, do not overtighten, as you may strip the screw.
16
String action refers to the distance between the strings and
the frets on a stringed instrument. Peavey technicians carefully set optimal string action on each bass guitar before it
leaves our factory; however, changes in temperature and
moisture (humidity), changing string gauges, making neck
adjustments or tuning can alter string action enough to
require a height adjustment to restore your guitar to factory
specications. Undesirable low action causes buzzing, while
abnormally high action makes your bass difcult to play.
1
String Action
Pickup Adjustments
Factory settings place pickups at the same volume
level; however, many players change the height of one
or more neck or bridge pickups to create their own output levels. To keep your factory warranty intact, Peavey
suggests you take your bass to an Authorized Peavey
Service Center to have the pickup adjustments made.
1
A properly intoned bass guitar will sound in tune no matter where you play along
the fretboard. Intonation is determined by the length of each string as controlled by
the location of each string’s saddle. To check intonation, complete all adjustments
to the truss rod and string action, and tune your guitar. Then, compare the fretted
sound of the 1th fret to the open harmonic of the 1th fret. (Harmonics
are created by lightly placing a nger against a string—in this case, at the
1th fret—and striking normally with your picking hand. You’ve done it correctly if you hear a clear, loud, bell-like tone.) If the notes are the same, no
adjustment is required. If they do not match, you will need to ne-tune each
offending string using the adjustment screws to move the saddle location.
If the fretted 1th note is at, adjust the saddle toward the neck. If sharp,
move it away from the neck. Note that on some bass guitars, you will need
to loosen strings before making saddle adjustments. Repeat the process
until the fretted sound of the 1th fret matches the open harmonic of the
1th fret.
1
Intonation
Neck and Truss Rod
Every Peavey bass guitar features an adjustable truss rod inside the neck. Truss rods
allow for adjustments in the neck to accommodate changes in string tension caused
by humidity, changing string gauges or tuning. As the backbone of your instrument,
the truss rod should always be adjusted rst during instrument setup. (Peavey rec-
ommends that you enlist the services of a qualied technician to make the required
truss rod adjustments on your instrument. Improper adjustment may damage your
neck and void your Peavey warranty.) To gain access to the truss rod, look for a
mm or mm allen wrench adjustment screw either at the end of the neck near the
body or at the opposite end near the headstock. Note that some bass guitars may
require neck removal to gain access to the neck pocket truss rod. The goal of truss
rod adjustment is to create the correct amount of bow in your bass guitar’s neck to
facilitate optimal playability.
To check the neck’s bow, hold the guitar in normal playing position and follow
this procedure for both outside strings (highest and lowest strings). Fret and
hold the string at the rst fret, while fretting and holding the same string with
your picking-hand thumb (where the neck and body meet, typically around the
16th fret). Then, stretch your picking hand index nger as far as you can to fret
0
Neck and Truss Rod
the middle area of the neck, somewhere around frets --. The distance your string travels to meet
the fret is the bow. Peavey recommends a .mm to . mm (.010" to .00") bow, easily measured and
set with a steel rule. Too much bow leads to buzzing in the middle of the neck because the strings are
too far away from the frets, while too little bow (backbow) causes excessive buzzing on open notes and
notes near the nut.
To make adjustments for neck bow or relief (backbow), adjust the truss rod in 1/-turn increments,
and then recheck. If your neck is backbowed, loosen the truss rod by turning it counterclockwise. If it
has too much bow, tighten the truss rod by turning clockwise. Remember, a little truss rod adjustment
makes a big change in how your bass plays. Improper adjustment may damage your neck and void your
Peavey warranty.
1
Warranty
Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.
What This Warranty Does Not Cover
The Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental, product modication or neglect; () damage occurring during shipment; () damage caused by repair or service performed by persons not authorized
by Peavey; () products on which the serial number has been altered, defaced or removed; () products not purchased from an Authorized Peavey Dealer.
Who This Warranty Protects
This Warranty protects only the original purchaser of the product.
How Long This Warranty Lasts
The Warranty begins on the date of purchase by the original retail purchaser. The duration of the Warranty for guitars is years *(+
years). [* denotes additional warranty period applicable if optional Warranty Registration Card is completed and returned to Peavey by
original retail purchaser within 0 days of purchase.]
What Peavey Will Do
We will repair or replace (at Peavey's discretion) products covered by warranty at no charge for labor or materials. If the product or
component must be shipped to Peavey for warranty service, the consumer must pay initial shipping charges. If the repairs are covered by
warranty, Peavey will pay the return shipping charges.
How To Get Warranty Service
(1) Take the defective item and your sales receipt or other proof of date of purchase to your Authorized Peavey Dealer or Authorized
Peavey Service Center.
OR
() Ship the defective item, prepaid, to Peavey Electronics Corporation, International Service Center, 1 Highway 11 & 0 East, Meridian,
MS 01. Include a detailed description of the problem, together with a copy of your sales receipt or other proof of date of purchase as
evidence of warranty coverage. Also provide a complete return address.
Limitation of Implied Warranties
ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE LENGTH OF THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Exclusions of Damages
PEAVEY'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT, AT PEAVEY'S OPTION. IF WE ELECT TO REPLACE THE PRODUCT, THE REPLACEMENT MAY BE A RECONDITIONED UNIT. PEAVEY SHALL NOT BE LIABLE FOR
DAMAGES BASED ON INCONVENIENCE, LOSS OF USE, LOST PROFITS, LOST SAVINGS, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER
ITEMS AT THE SITE OF USE, OR ANY OTHER DAMAGES WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, EVEN IF PEAVEY HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to
you.
This Warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
If you have any questions about this warranty or services received or if you need assistance in locating an Authorized Service Center,
please contact the Peavey International Service Center at --1 (toll-free) or customerservice@peavey.com. Features and specications subject to change without notice.
Warranty
Peavey Electronics Corporation • 0 Hartley Peavey Drive • Meridian, MS 0
(601) -6 • FAX (601) 6-1 • www.peavey.com
© 006
EX0000
Loading...