Peavey HB 1 DATASHEET

HHBB

™™

-- 11 SStteerreeoo HHeeaaddpphhoonnee BBoooosstteerr

•• BBoooossttss WWeeaakk HHeeaaddpphhoonnee SSoouurrcceess TToo SSttuuddiioo LLeevveellss

•• LLeevveell CCoonnttrrooll

•• TTwwiinn SStteerreeoo PPhhoonnee OOuuttppuuttss

•• LLooww NNooiissee,, FFuullll BBaannddwwiiddtthh PPeerrffoorrmmaannccee

•• DDrriivveess 88 ΩΩ TToo 660000 ΩΩ HHeeaaddpphhoonneess

•• FFlleexxiibbllee TThhrreeee--WWaayy IInnppuutt,, ((SStteerreeoo,, MMoonnoo,, SStteerreeoo LLRR))

The HB

™

- 1 headphone booster can be used with tape recorders,
mixers or other equipment to provide additional
headphone outputs with increased output power. The HB - 1 can
also be used to add high quality headphone outputs to
equipment with line outputs only. Simply plug the line level
source into the HB - 1 and connect your headphones into the
output of the HB - 1.

EExxtteerrnnaall PPoowweerr SSuuppppllyy JJaacckk
Provided for connection of the external power supply. Insert the
power supply plug fully into the socket before making the AC
outlet connection.

CCaauuttiioonn::

Use only the power supply provided with this product. If
the original power supply must be replaced, consult your dealer
or the factory for assistance in obtaining the correct replacement.
Failure to use the correct power supply could result in fire or
shock hazard, circuit damage, decreased performance, or non­operation.

PPoowweerr LLEEDD
The red pilot light (LED) will illuminate to indicate that power is
being supplied to the unit.

IInnppuuttss
Mono - Plugging a (TS) Mono phone plug source into the jack
labeled MONO will result in a mono signal in the left and right
earcups.

Stereo - Plugging a (TRS) Stereo phone plug source into the jack
labeled STEREO will result in a stereo LR signal in the head­phones.

Stereo LR - Plugging a (TS) left phone plug source and a (TS)
right phone plug source into the appropriately labeled jacks will
result in a stereo LR signal in the headphones.

LLeevveell
Controls the output signal level. Maximum output level is
obtained by rotating this control fully clockwise.

SStteerreeoo OOuuttppuutt ((HHeeaaddpphhoonnee 11 ++ 22))
These output jacks are intended for use with 8 Ω to 600 Ω head­phones or the Peavey PD

™

-4 headphone distribution system.

DDiimmeennssiioonnss

5.75"W x 2"H x 4.375"D

WWeeiigghhtt

1.2 lbs.

5500ΩΩ 660000ΩΩ
Input for 1 Volt 1 Volt
max out 0 dBV=2 dBu 0 dBV=2 dBu

Output 300 mW 100 mW

Frequency 20 Hz - 20 kHz 20 Hz - 20 kHz
response +0, -1 dB +0, -1 dB

Distortion <.005%@ 1 kHz <.003% @ 1kHz

Signal to 102 dB 102 dB
noise

Crosstalk <-60 dB <-70 dB

SSPPEECCIIFFIICCAATTIIOONNSS HHBB™™11

SStteerreeoo HHeeaaddpphhoonnee BBoooosstteerr

Features and specifications subject to change without notice.

Peavey Electronics Corporation • 711 A Street • Meridian • MS • 39301 [phone] • FAX [phone] • www.peavey.com

©2003 Printed in the U.S.A. 8/03

80303104

SSPPEECCIIFFIICCAATTIIOONNSS