Peavey 18S User Manual

SPECIFICATIONS PM™18S
TTyyppee::
Back-electret condenser microphone
PPiicckkuupp ppaatttteerrnn::
Cardioid
FFrreeqquueennccyy rreessppoonnssee::
50 Hz to 20 kHz
SSeennssiittiivviittyy::
-39 dBV/Pa
RRaatteedd iimmppeeddaannccee::
250 Ohms
MMiinniimmuumm llooaadd iimmppeeddaannccee::
1k Ohms
SS//NN rraattiioo::
68 dB
DDyynnaammiicc rraannggee::
106 dB
PPoowweerr ssuuppppllyy::
9~52 VDC
CCuurrrreenntt ccoonnssuummppttiioonn:
3 mA
FFeeaattuurreess::
DDiimmeennssiioonnss:
Top diameter 0.5" (12.5 mm) x length 1 mm)
NNeett wweeiigghhtt:
7.75 oz. (220 g)
:
:
• Back-electret condenser element
:
8.1" (460
DDeessccrriippttiioon
The PM™18S is truly the ultimate podium microphone, unique combination of features to suit any formal speaking application.
tubing allows for practically infinite positioning choices while maintaining a clean appearance.
electret condenser capsule offers tailored, smooth frequency response with an excellent cardioid pickup pattern and high gai performance before feedback.
the PM 18S provides additional mechanical isolation from structure-born noise and mechanically coupled
locks the microphone in place to deter theft or improper removal.
the PM 18S may be plugged directly into an XLR-type receptacle or mounted to a microphone stan or boom microphone stand adapter
phantom po supplies DC voltage 9~52V. An LED located in the of the of the output module) indicates when the PM 18S is powered.
n
offering a
The
utilization of dual-flex
The specially
The collet mount supplied with
The
supplied clamp effectively
In addition to the collet mount
The PM 18S can operate on an
microphone (upper portion
designed back-
n
feedback.
with a conventional
.
wer source that
between
base
a
,
d
y
• Cardioid pickup pattern
• Specially tailored smooth frequency response
• High gain before feedback
• Collet-type mounting flange with mechanical isolation system
• Security locking system to prevent unauthorized removal
• Operational from 9~52 VDC phantom power source
• LED power indicator
MMaaxxiimmuumm SSPPLL::
132 dB
SPECIFICATIONS PM™18S
AARRCCHHIITTEECCTTUURRAALL && EENNGGIINNEEEERRIINNG SSPPEECCIIFFIICCAATTIIOONNS
The microphone shall be back­electret, condenser type with frequency response of 50 Hz to 20 kHz. The microphone shall have cardioid response pattern with a rear response that is typically -20 dB from the front response. The microphone shall have an output level of -39 dBV/pascal with a nominal impedance of 250 Ohms. The microphone shall have a low-gloss finish. Microphone dimensions shall be 0.5" (12.5 mm) i diameter at the element and 18.1" (460 mm) long. The output shall properly interface the microphone with any
Dual, flexible tubing shall be
supply. incorporated in the neck assembly to allow proper positioning of the microphone. The microphone shall be a
Peavey PM 18S.
S
9 to 52 Volt phantom power
CCOOLLLLEETT MMOOUUNNTT IINNSSTTAALLLLAATTIIOON
Remove template from carton. Position position on the upper right or left corner of the reading surface is most practical.
place while you mark center clearance and (3) mounting hole centers.
the template at the desired
the lectern. Placing it near
tape to hold the template in
Use
the location of
Remove the template and drill a 1"
G
a
a
N
pilot
attach
,
.
e
SSEECCUURRIITTYY LLOOCCKK PPRROOVVIISSIIOON
After the installation of the microphone, simply slip the security clamp around the microphone cabl and position around the end of the output module beneath the mounting surface. Engage the jaws of the clamp and tighten securely by squeezin with your fingers or pliers.
While the clamp is in place, the microphone cannot be removed. Thi prevents theft and protects the mechanical isolation system from damage likely to occur if the XLR on the microphone cable is pulled through the collet.
To remove the microphone, disconnect the microphone cable from the output module and remove the security clamp by sliding one ja downward until the teeth disengage.
22 YYEEAARR LLIIMMIITTEEDD WWAARRRRAANNTTY
NNOOTTEE::
For details, refer to the warranty statement. For copies of thi statement, contact Corporation, at P.O Box 2898, Meridian, Mississippi 39301-2898, or go online to www.peavey.com.
Peavey Electronics
N
e
g
s
w
Y
s
(25.4 mm) center clearance hole. Next drill (3) 3/32" (2.38 mm) screw holes.
After making sure the 1 1/2" (38.1 mm) suspension foam washer is in the base of the collet mount, the collet mount to the lectern using the three mounting screws provided.
Insert the connector end of the microphone into the mount and gently press down to the desired depth. The connector end must penetrate washer.
n
output module cap to rest on collar top. mechanical isolation system becomes ineffective.
tighten or counterclockwise to loosen the tension on the suspension system Optimal tension is only enough to prevent the downward on its own
microphone to prevent it from moving up, connect the microphone into the microphone output module.
vibration module nor the come in contact with the collet or th mounting surface of the
the lower suspension foam
CCAAUUTTIIOON
If this happens, the
Turn collet collar clockwise to
microphone from slipping
Holding
CCAAUUTTIIOON
the top portion of the
N
isolation, neither the output
top of the collet
N
: Do not allow the
the collet
weight.
cable firmly
: To preserve maximum
security clamp should
lectern.
2
SPECIFICATIONS PM™18S
Pickup Patterns
0
45 45
90 dB
135 13
125 H
45 45
90 dB
135 13
100 0 H
5 10
15
20
25
18
0
z
0
5 10
15
20
25
0
18
z
z
500 0 Hz
0
5 10
15
20
25
0
18
0
5 10
15
20
25
0
18
90
5
90
5
0
z
250 0 Hz
5 10
15
20
25
18
0
0
5 10
15
20
25
18
0
90
90
5
45 45
90
5
90
5
90 dB
135 135
250 H
45 45
90 dB
135 13
45 45
90 dB
135 13
500 H
45 45
90 dB
135 13
0
45 45
90 dB
135 13
100 00 Hz
5 10
15
20
25
0
18
90
5
3
+ 5 hidden pages