Peavey 10PM User Manual [en, de, es, fr]

EuroSys 10PM

Powered Monitor Enclosure

OPERATING INSTRUCTIONS

EuroSys 10PM

Powered Monitor Enclosure

OPERATING INSTRUCTIONS

WARNING! TO PREVENT SHOCK OR FIRE HAZARD DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE. DO NOT REMOVE FROM CASE. NO USER SERVICEABLE
PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL.
REPLACE FUSE ONLY WITH ONE OF THE SAME TYPE AND SPECIFICATION.

Thank you for choosing Peavey's Eurosys 10PM powered monitor enclosure as part of your sound
reinforcement system. We take great pride in the design and manufacture of our units and you can expect
top performance and reliability. Your Eurosys 10PM has been rigorously tested before packing and
despatch to your dealer. It has been designed to run from a nominal 230 Volt AC mains supply.

1. AMPLIFIER INPUTS

Use to connect line level signals from the monitor send of the mixer. Two sockets are provided to
allow connection to further Eurosys 10PM powered monitors. (Daisy chaining).

2. VOLUME

This slider controls the level or volume of the enclosure.

3. 4 BAND GRAPHIC EQUALISER

Four sliders allowing up to +/- 12dB of adjustment at the centre frequencies of: - 100Hz, 1KHz, 5KHz
and 10KHz. Use to assist with any feedback problems.

4. ~ PILOT LIGHT

Illuminates when AC mains power is being supplied to the amplifier.

5. EXTENSION SPEAKER SOCKET

Allows connection of a further unpowered monitor with an impedance of 8 ohms. The power
amplifier will develop full power into 4 ohms. (65 Watts).

6. POWER SWITCH

Use to turn the Eurosys 10PM ON or OFF

7. MAINS CONNECTOR & FUSE HOLDER

An IEC 320 combined mains connector and fuse holder is fitted. A separate 3-wire mains cord fitted
with a moulded plug is supplied.

8. 13 AMP PLUG REPLACEMENT

As the colours of the wires in the mains lead or cord of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:-

- the wire which is coloured green and yellow must be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol, or coloured green or green yellow.

- the wire which is coloured blue must be connected to the terminal which is marked with the letter
N or coloured black.

- the wire which is coloured brown must be connected to the terminal which is marked with the
letter L or coloured red.

WARNING - THIS APPARATUS MUST BE EARTHED

SPECIFICATIONS
POWER OUTPUT (TYPICALLY) POWER REQUIREMENTS

45 Watts into 8 ohms 185 Watts at 65 Watts output
65 Watts into 4 ohms

INPUT SENSITIVITY MAINS VOLTAGE REQUIREMENTS

0.4 volt for 45 Watts into 8 ohms 230 Volts AC (only) 50/60 Hz

FUSE RATING

0.8 ampere anti surge.

IN CASE OF DIFFICULTY CONSULT YOUR AUTHORISED PEAVEY DEALER
Due to our efforts for constant improvement, features and specifications are subject to change

without notice.

EuroSys 10PM

Enceinte de retour amplifiŽe

MANUEL DÕUTILISATION

ATTENTION, AFIN DE PREVENIR TOUT RISQUE DE CHOC ELECTRIQUE OU DE FEU, NE
PAS EXPOSER CE MATERIEL A LA PLUIE OU A LÕ HUMIDITE. NE PAS OUVRIR LE
CHASSIS, IL NE CONTIENT AUCUNE PIECE UTILISABLE. FAIRE EFFECTUER LES
REPARATIONS PAR UNE PERSONNE QUALIFIEE. REMPLACER LE FUSIBLE PAR UN
MODEL DU MEME TYPE.

Nous vous remercions dÕavoir choisi lÕenceinte de retour amplifiŽe Eurosys 10PM . Nous sommes trŽs fier
de la conception et de la rŽalisation de ces enceintes dÕun excellent rendement et dÕune grande fiabilitŽ.
Votre enceintes EuroSys 10PM a ŽtŽ soumise ˆ des essais rigoureux avant dÕ•tre conditionnŽe et expŽdiŽe ˆ
votre revendeur. Elle doit •tre alimentŽe en 230V AC.

1. ENTREES DE LÕAMPLIFICATEUR

Connectez la sortie au niveau ligne ÔmonitorÕ de votre table de mixage ˆ ces entrŽes. Deux prises en
parall•le sont proposŽes pour permettre le cha”nage dÕenceintes EuroSys 10PM.

2. VOLUME

Ceci contr™le le volume de lÕenceinte.

3. EQUALISEUR GRAPHIQUE 4 BANDES

4 faders autorisant une correction de + ou - 12 dB ˆ 100Hz, 1KHz, 5KHz, 10KHz. Employez ces
contr™les pour corriger tout probl•me de feedback.

4. DIODE DE MISE SOUS TENSION

Cette diode sÕallume lorsque lÕamplificateur est alimentŽ.

5. FICHE POUR EXTENSION

Elle permet la connection de lÕEuroSys 10PM ˆ dÕautres enceintes non amplifiŽes dÕune impŽdance
minimum de 8 Ohm tel lÕEuroSys 12M. LÕamplificateur de puissance developpera sa pleine
puissance (65 Watt) sous 4 Ohm.

6. INTERRUPTEUR DÕALIMENTATION

Met lÕEuroSys 10PM en et hors fonction.

7. PRISE DÕALIMENTATION ET FUSIBLE

Cette prise, accompagnŽe dÕun porte-fusible, permet la connection du cordon dÕalimentation IEC
fourni.

ATTENTION Ð CET APPAREIL DOIT ETRE RELIE A LA TERRE

SPECIFICATIONS

PUISSANCE NOMINALE PUISSANCE NECESSAIRE

45 Watt continus sous 8 Ohm 185 Watt pour une puissance de sortie de 65 Watt
65 Watt continus sous 4 Ohm

SENSIBILITE DÕENTREE ALIMENTATION

0,4V pour 45 Watt sous 8 Ohm 230V AC 50/60Hz uniquement

FUSIBLE

0,8 Amp•re, fusible retardŽ.

EN CAS DE DIFFICULTƒS, CONSULTEZ VOTRE REVENDEUR PEAVEY

Etant donnŽe notre politique de dŽveloppement continu, les caractŽristiques et spŽcifications sont sujets ˆ
des modifications sans prŽavis.