Page 1
Congratulations on your purchase!
To get optimum performance from your P-930 Drum Pedal,
please read this Instruction Manual before playing.
P-930
PEARL DRUM PEDAL
Instruction Manual
Beater Holder Link
Key Bolt
(for Beater Angle Adjustment)
Beater Angle Cam
Spring Assembly
Spring
Hoop Clamp
Wing Bolt
Upper Nut
Lower Nut
Footboard
DuoBeat Beater
(2-Surface Beater)
Key Bolt
(for Beater Setting)
Chain
Click Lock
Page 2
AB
Fig. 2
Beater Holder Link
DuoBeat Beater
Key Bolt
Tuning Key
Fig. 1
Fig. 3
Fig. 4-A
Fig. 4
Key Bolt
DuoBeat Beater
Beater Angle Cam
Upper Nut
Spring
Lower Nut
Click Lock
Surface Material
Felt Surface
Sound
Full,
Warm Sound
Surface Material
Plastic Surface
Sound
Sharper,
Punchier Sound
DuoBeat Beater (2-Surface Beater)
The DuoBeat Beater features a Felt Surface (A) for a full,
warm sound and a Plastic Surface (B) for a sharper,
punchier sound. Use the side that best suits your playing
style (Fig.1).
Beater Setting
Insert the shaft of the DuoBeat Beater into the Beater
Holder Link and tighten the Key Bolt with the provided
Tuning Key to secure the Beater at the desired height.
Experiment with different Beater heights to find the best
combination of power and speed (Fig.2).
Beater Angle Adjustment
Depending on your preference, the Beater can be
positioned closer or farther away from the Bass Drum Head.
This is accomplished by loosening the Key Bolt on the
Beater Angle Cam and swinging the Beater to the desired
angle. Re-tighten the Key Bolt to secure the angle (Fig.3).
Spring Tension Adjustment
The P-930 Drum Pedal features Peari’s patented Click
Lock spring tension retention system. To increase the
spring tension, disable the Click Lock by lifting the lever
upward, loosen the Upper Nut and press downwards.
Keep the position of the Upper Nut and tighten the Lower
Nut until the desired tension is achieved (Fig.4). To
decrease spring tension, disable the Click Lock by lifting
the lever upward, loosen the Upper Nut and loosen the
Lower Nut until the desired tension is achieved. When the
desired spring tension is achieved, tighten the Upper Nut
to keep the spring tension from loosening then press the
Click Lock lever down to engage the grooves around the
Lower Nut until you feel the lever "Click" (Fig.4-A). Before
playing, make sure that both Upper and Lower Nuts are
tight and the Click Lock lever is in a vertical position with
both sides of the lever engaged in the grooves around the
Lower Nut.
Page 3
http://www.pearldrum.com
Products and specifications are subject to change without notice.
Printed in China
-1212-
Fig. 6-A Fig. 6-B
Fig. 5
Hoop Clamp
Wing Bolt
Interchangeable Cam System
The P-930 Drum Pedal is equipped with Pearl's Patented
Interchangeable Cam system which allows you to change
the feel and action of the pedal. It comes from the factory
with the Orange Cam installed, which is an "Off-Centered"
cam design with light feel in the beginning that accelerates with power and speed at impact. Removing the
Orange Cam reveals Pearl's "Perfect Circle" Cam that's
known for its power and natural, balanced action.
To remove the Orange Cam, insert the provided Hex
Wrench into the center of the Orange Cam between the
gap of the Chain and loosen the Screw (Fig.6-A). Pull the
Orange Cam straight up and away from the Chain
(Fig.6-B). Reverse the steps to reattach the Orange Cam.
Orange Cam
Chain
Hexagonal Wrench
Screw
Hoop Clamp Wing Bolt
Place the Pedal on the Bass Drum Hoop and square the
Pedal to the floor. Tighten the Wing Bolt to clamp the
Pedal firmly in place (Fig.5).
NOTE
Make sure to remove the Pedal when moving the Bass Drum
to prevent damage to the Bass Drum and the Pedal.
TIP
The Orange Cam can be attached with either end up.
NOTE
Periodically apply lube to parts such as the Chain, Bolts and
Nuts, Footboard Hinge and Bearings.
Fig. 7-A Fig. 7-B
Footboard
Footboard
Base Plate
Flat Head
Screw
Base Plate
Flat Head
Screw
PowerShifter
The P-930 Drum Pedal is equipped with Pearl's patented
PowerShifter Function that changes the leverage of the
Footboard and thus the feel of your pedal. By default, it's
set to the (A) position (Fig.7-A). To change to the (B)
position, remove the two Flat Head Screws under the
Base Plate using the provided Hex Wrench. Move the
Footboard toward the front of the pedal and insert the
guides under the Heel into the appropriate holes in the
Base Plate. Make sure the Heel is flush with the Base
Plate and reattach the Flat Head Screws (Fig.7-B). Tighten
the Screws securely with the provided Hex Wrench.
A
Light Feel
B
Heavy Feel
Loading...